Mtx Audio RT8PT Bruksanvisning

Mtx Audio mottagare RT8PT

Läs gratis den bruksanvisning för Mtx Audio RT8PT (24 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 10.5 recensioner. Har du en fråga om Mtx Audio RT8PT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/24

RT8PT

20cm (8") Powered Tube Enclosure

120W RMS

Designed in Phoenix - AZ, USA

www.mtx.eu.com

www.mtx.com

Line In

PWR

Gain

6V-0.1V 50Hz-200Hz

Rem.

Prot.

PWR

GND+12V

FUSE

LPF

EBC PortHLI

www.mtx.com - www.mtx.eu.com

Introduction

Thank you for purchasing an MTX Audio Hi-Performance powered tube. Proper installation matched with MTX

speakers and ampliers provide superior sound and performance for endless hours of waking the neighbors,

slammin' your friends or at out stomping wanna-be players. Congrats and enjoy the ultimate audio experience

with MTX !

Features

• Powered vented enclosure

• Subwoofer : 20cm (8")

• Amplier Max Power : 360W

• Amplier RMS Power : 120W

• EBC remote included

• High and low level inputs

• Dimensions : 25x25x54cm

Control Panel on the Amplier

Owner’s Manual - RT8PT

Speaker level inputs - This input will allow the amplier to operate from source units with speaker-level outputs.

Output speaker leads from the source unit should be tied directly to the wire harness provided with the amplier.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.

EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while

the EBC itself can be placed anywhere in the vehicle for on demand bass adjustments. EBC is included.

RCA Inputs - These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need

a minimum level of 100mV output for proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-

ated noise entering the system.

Gain Control - The gain control matches the input sensitivity of the amplier to the source unit being used. The

operating range varies from 100mv to 6V.

Adjusting the gain

1. Turn the gain control on the amplier all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the amplier until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The amplier is now calibrated to the output of the source unit.

Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is

adjustable from 50Hz to 200Hz..

Protection LED - When the amps is in thermal protection, the LED turns to red.

PowerOn LED - The LED illuminates red when the amp is switched on.

(+12V) Power Terminal - This is the main power input for the amplier and

must be connected directly to the positive terminal of the vehicles battery

for proper operation. Use caution when installing (+12V) power cable in

the vehicle. Avoid running this cable parallel with RCA cables, antennas, or

other sensitive equipment due to massive currents that can induce noise

into the audio system. It is also very important to have a tight, secure con-

nection for maximum performance. MTX recommends using a minimum of

6mm2 full copper power wire with the MTX RT8PT powered tube.

Remote Terminal – The powered tube can be turned on by applying 12 volts to this terminal. Typically this voltage is

supplied by a wire from the source unit marked “remote” or “power antenna”.

Ground Terminal – A proper ground is required for your amplier to operate at peak performance. A short ground

cable the same diameter as the power cable should be used to attach the ground terminal directly to the chassis of the

vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be attached.

Fuses - When the fuse blows, replace it with the same value. The RT8PT uses a 20A fuse.

Caution : Never use a higher rated fuse !

Installation & Mounting

MTX recommends your new RoadTHUNDER powered tube to be installed by an Authorized MTX retailer. Any deviation

from specied installation instructions can cause serious damage to the amplier, speakers and/or vehicles electrical

system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior

to turn on your system !

1. Disconnect the vehicle’s negative battery cable.

2. Determine the mounting place for your MTX powered enclosure. Hook it with the provided belts. Keep in mind there

should be sucient air ow for proper cooling.

3. Install a positive (+) power cable from the vehicle’s battery through the rewall using a grommet or rewall bushing

to avoid cable damage from sharp edges of the rewall. Run the cable through the interior of the vehicle and connect

it to the amplier’s (+12V) terminal (8). Do Not connect to the battery at this time.

Note : Use only proper gauge wire for both positive and negative connections.

4. Install a circuit breaker or fuse within 20cm of the battery. This eectively lowers the risk of severe damage to you

or your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched o or the fuse is taken

out of the fuse holder untill all connections are made. Now connect your positive power cable to the positive battery

terminal of the battery.

5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare

metal surface. Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the (GND)

terminal on the MTX amplier (10).

6. Connect a remote turn-on wire from the source unit to the powered tube remote terminal (9). If the source unit does

not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.

7. Connecting signal cables to the amplier : There are two ways to supply the signal to your MTX powered tube.

• To get maximum performance, we suggest connecting a high quality RCA to the corresponding outputs at the source

unit and inputs of the amplier.

• If a source unit is being used without RCA outputs, use the included high-level amplier’s speaker terminals (1) using

the right gauge speaker wire.

8. Double check all previous installation steps, in particular, wiring and component connections. Once veried, recon-

nect the vehicle’s negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.

Note : Gain Levels on the amplier should be turned all the way down (counter clockwise) before proceeding with

adjustments.

Produktspecifikationer

Varumärke:	Mtx Audio
Kategori:	mottagare
Modell:	RT8PT
Färg på produkten:	Meerkleurig
Förpackningens vikt:	357 g
Förpackningens bredd:	262 mm
Djuppackning:	191 mm
Förpackningshöjd:	61 mm
Rekommenderad ålder (max):	99 jaar
Rekommenderad ålder (min):	8 jaar
Typ av förpackning:	Doos
Ursprungsland:	Tsjechische Republiek
Material:	Kunststof
Antal per paket:	1 stuk(s)
Föreslaget kön:	Jongen/meisje
Batterier krävs:	Nee
Antal bitar:	327 stuk(s)
Ljudeffekter stöds:	Nee
Montering krävs:	Ja
Typ produkt:	Bouwpakket
Antal paket:	1
Antal (inre) fraktpaket per (yttre) huvudpaket:	6 stuk(s)
EU TSD-varning:	No warning applicable, Not for children under 36 months
Monteringstid:	60 min
EU TSD-språk:	English, German, French, Italian, Spanish, Swedish, Dutch
SALT:	B0BPCCKL5V