NAKS 20D-DBFF-900 Bruksanvisning
NAKS
ventilationskåpa
20D-DBFF-900
Läs gratis den bruksanvisning för NAKS 20D-DBFF-900 (6 sidor) i kategorin ventilationskåpa. Guiden har ansetts hjälpsam av 26 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 13.5 recensioner. Har du en fråga om NAKS 20D-DBFF-900 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
RECEIVING AND INSPECTION
Immediately upon receipt of a shipment, carefully inspect for
damage and shortage. Turn the impeller by hand to see that it
turns freely and does not bind. If any damage and/or shortage is
detected or suspected, the carrier must be asked to conduct an
inspection. The consignee’s representative should not accept a
shipment without a notation on the delivery receipt indicating items
not delivered or the apparent extent of damage.
When a shipment is opened and damage is found which was not
evident externally (concealed damage), it is mandatory that the
consignee request an immediate inspection by the carrier. Report
any damage to the carrier within 15 days. Failure to report damage
within the above time limit will result in rejection of a claim.
HANDLING
When handling fans and their accessories, always use equipment
and methods that will not cause damage. Fans should be lifted
using slings and padding or spreaders to avoid damage.
CAUTION! Always make sure that all lifting and handling
equipment and techniques conform to current safety standards.
Avoid lifting fans in a way that will bend or distort fan parts. Never
pass slings or timbers through the orices of fan.
CAUTION! Do not lift by the fan hood. Fans with special coatings
or paints must be protected in handling to prevent damage.
STORAGE
Fans are protected against damage during shipment. If they
cannot be installed and put into operation immediately upon receipt
certain precautions are necessary to prevent deterioration during
storage. Responsibility for integrity of fans and accessories during
storage must be assumed by the user. The manufacturer will not
be responsible for damage during storage. These suggestions are
provided solely as a convenience to the user, who shall make his
own decision as to whether to use any or all of them.
INDOOR: The ideal storage environment for fans and accessories
is indoors, above grade, in a low humidity atmosphere which
is sealed to prevent the entry of blowing dust, rain, or snow.
Temperatures should be evenly maintained at between 70°F and
105°F (wide temperature swings may cause condensation and
“sweating” of metal parts). Windows should be covered to prevent
temperature variations caused by sunlight. Provide thermometers
and humidity indicators at several points and maintain the
atmosphere at 40% relative humidity, or lower.
It may be necessary to use trays of renewable desiccant or
portable dehumidier to remove moisture from the air in the
storage enclosure.
Thermostatically controlled portable heaters (vented to outdoors)
may be required to maintain even temperatures inside the
enclosure.
CAUTION! Provide re extinguishers, or re alarms, or emergency
response communication to protect building and equipment
against re damage. Be sure that building and storage practices
meet all local, state and federal re and safety codes.
The following fans or accessories must be stored indoors, in a
clean dry atmosphere:
a. Propeller wall fans not in wall housings.
b. Any fan is protected by a cardboard carton.
c. Motors dismounted from fans.
d. Spare wheels or propellers.
e. Belts, sheaves, bushings and other parts when not
mounted on fan.
f. Boxes, bags or cartons of hardware.
g. Curbs
h. Dampers
Remove any accumulations of dirt, water, ice or snow and wipe
dry before moving indoor storage. Allow cold parts to reach room
temperature to avoid “sweating” of metal parts. Open boxes
or cartons. Remove any accumulated moisture; if necessary
use portable electric heaters to dry parts and packages. Leave
coverings loose to permit air circulation and to permit periodic
inspection.
Rotate wheels or propellers by hand to distribute bearing grease
over the entire bearing surfaces.
Store at least 3 ½” off the oor on wooden blocks covered with
moisture proof paper or polyethylene sheathing. Provide aisles
between parts and along all walls, to permit air circulation and
space for inspection.
OUTDOOR: Fans designed for outdoor use may be stored
outdoors, if absolutely necessary. The storage area should be
reasonably level and drained or ditched to prevent accumulation
of water. Fencing and lighting for security are desirable. Roads
or aisles for portable cranes and hauling equipment are needed.
Consider the use of drift fencing to minimize accumulation of
blowing snow or dirt.
The following fans may be stored outdoors, if dry indoor storage
space is not available:
a. Fans intended for outdoor use that are crated in wood.
b. Wall fans installed in wall housings.
INSTALLATION & MAINTENANCE INSTRUCTIONS
Models 08D-DB, 10D-DB, 20D-DB, 28D-DB, 36D-DB
Read and Save These Instructions
NAKS Form 613161
_________________________________________________________________________________________________________________________
2017 © North American Kitchen Solutions
172 Reaser Court, Elyria, OH 44035
Toll Free: (800) 715-1014
customerservice@naksinc.com
Page 1 of 6
Produktspecifikationer
| Varumärke: | NAKS |
| Kategori: | ventilationskåpa |
| Modell: | 20D-DBFF-900 |
Behöver du hjälp?
Om du behöver hjälp med NAKS 20D-DBFF-900 ställ en fråga nedan och andra användare kommer att svara dig
ventilationskåpa NAKS Manualer
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
21 September 2025
ventilationskåpa Manualer
- Infiniton
- Balay
- IKEA
- Giles
- Continental Edison
- Tesy
- Amica
- Svan
- Mora
- Viking
- Berbel
- Witt
- Honeywell
- Franke
- Inventum
Nyaste ventilationskåpa Manualer
23 Oktober 2025
21 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
17 Oktober 2025
16 Oktober 2025