Neets KNX Bruksanvisning
Läs gratis den bruksanvisning för Neets KNX (8 sidor) i kategorin Mjukvarulicens och förlängning. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 3.6 stjärnor baserat på 9 recensioner. Har du en fråga om Neets KNX eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
Doc#: - - KNX manual.docx 1 8 315 0001 002 of
KNX integration for Project
Designer
Introduction
With this KNX integration Project Designer possible control KNX devices like on/off, to it is to
dimming, blinds, scene control etc.
This implementation intended integration smaller installations, not larger residential is for in for
installations.
The interface the K bus achieved using a standard LAN KNX interface that to NX is by to IP
several KNX manufacturers make.
The integration license based, and bought licenses are added your company account is to at
Neets where your own user attached. This means that you need login Project Designer is to to to
be able use this integration. to
Requirements
Neets Control system that supports controlling LAN devices
One LAN connection the Project Designer project that should interface the KNX free in to
interface.
A KNX interface that supports KNXnet/IP / KNX tunneling. IP TP
Tested and verified:
o Gira KNX interface, PN: 216800/1 IP 00
o Weinzier, KNX Interface IP 730
o ABB i-bus® KNX Interface IPS/S 2 IP
Neets Project Designer version 1.12 newer .0 or
Basic knowledge KNX and KNX Group Addresses of
Internet connection
Doc#: - - KNX manual.docx 2 8 315 0001 002 of
What are the limitations and what not supported is
Due memory constraints our control systems only support creation to in we of 50
different group addresses large control systems like QueBec Pro, SieRRa II, Tango, AlFa on
II, DelTa and 10 group addresses small control systems like OsCar and EcHo Plus. on
Decimal numbers floating point values not supported, and rounding and precision in are of
values might not completely accurate. be
As most the interfaces only supports one incoming network connection, interface of IP an
is required Neets control system that needs access the KNX bus. Please note for each to
that an not the same interface. IP router is as an IP
This integration supports feedback a way where get a reply the same group in we on
address sending E.g. a blind set half way, then the KNX bus will as we are to. if is to go
tell what the current state which might different. the intention this is be If is to react on
kind feedback, then a new group address and then only use the feedback of can be created
part it. of
Normally when using level sequences Neets control systems, the default value in is
transmitted the device startup. This will not the case KNX level sequences to on be for as
it could cause unwanted behavior.
Only the following datatypes supported are
o DPT-1
o DPT-2
o DPT-5
o DPT-6 (except Data point sub type DPST-6- 20)
o DPT-9 (except decimals values) on
o DPT- 17
o DPT- 18
o DPT- 20
o DPT- 26
Doc#: - - KNX manual.docx 3 8 315 0001 002 of
Group addresses and ETS software
Three level structure
We working with group addresses the Three format. KNX recommends using the are in “ level”
three level structure smaller ojects. A three level group address can look something like for pr
“1/0/9”.
There some recommendations from KNX how setup group addresses the KNX devices are to on
but will not cover that here. Please see the we
KNX Project Design Guidelines
document.
ETS software
T group addresses might already configured the ETS software. However it not possible he be in is
to directly import ETS file into Project Designer, but the following steps will make a bit an it
easier prepare entering the group addresses Project Designer. to for in
1) Open your KNX configuration file the ETS software. in
2) Click the menu. on “Reports” in
3) Select Group Addresse s.
Project Designer
Group Address dialog
In the Group Address dialog all the group addresses and the corresponding data type should ir be
defined.
Optionally a name each item provided make easier distinguish the items when for can be to it to
used in the project. a name not provided a default one created. If is is
When selecting data types that generates level sequences, a minimum and maximum range can be
defined. This especially useful when operating with e.g. temperatures and the desired range is is
within something that the HVAC system handle, instead using negative temperatures. can of
Produktspecifikationer
| Varumärke: | Neets |
| Kategori: | Mjukvarulicens och förlängning |
| Modell: | KNX |
| Antal licenser: | - licens/-er |
| Typ av programvara: | Upgradera |
Behöver du hjälp?
Om du behöver hjälp med Neets KNX ställ en fråga nedan och andra användare kommer att svara dig
Mjukvarulicens och förlängning Neets Manualer
28 Augusti 2024
Mjukvarulicens och förlängning Manualer
- Adobe
- Acronis
- D-Link
- Canon
- Digi
- IRIS
- Zebra
- ABBYY
- Symantec
- Avaya
- Axis
- Trend Micro
- Telestream
- Panasonic
- Lancom
Nyaste Mjukvarulicens och förlängning Manualer
1 Januari 2025
1 Januari 2025
28 December 2024
15 December 2024
26 Oktober 2024
8 Oktober 2024
3 Oktober 2024
3 Oktober 2024
25 September 2024
25 September 2024