Netgear RPS4000v2 Bruksanvisning

Netgear Inte kategoriserad RPS4000v2

Läs gratis den bruksanvisning för Netgear RPS4000v2 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 5.5 recensioner. Har du en fråga om Netgear RPS4000v2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Installation Guide

Check the LEDs

Power system indicators are listed in the following table:

Label Color Activity Description

PWR

(Power)

Green On Power is being provided to the RPS4000v2.

Power

Module

Status

Green On An APS1000W is present and working properly.

Yellow On An APS1000W is present but is not working

properly.

Off Off There is no APS1000W present.

RPS Port

Status

Green On The switch supports dynamic power allocation, and

the APS1000W in the corresponding RPS port and

power module bay is supplying power to the switch.

Blinking The switch supports dynamic power allocation, but

the APS1000W in the corresponding RPS port and

power module bay is not supplying power to the

switch. Power is being supplied by the APS1000W in

a different power module bay.

Yellow On The switch does not support dynamic power

allocation, and the APS1000W is providing power to

the switch.

Blinking The switch does not support dynamic power

allocation, but the APS1000W is not supplying

power to the switch.

Off Off No power is being supplied to the switch, or the

switch is not recognized.

Redundant Power System and Power Bank

Model RPS4000v2

The Redundant Power System and Power Bank RPS4000v2 provides power

system redundancy to external devices such as NETGEAR chassis switches,

managed switches, or smart switches with an RPS capability.

Each RPS4000v2 includes four power module bays, and can provide a maximum

output of 4000W when four APS1000W power supply units (PSU) are installed.

The RPS4000v2 can supply power to devices that support dynamic power

allocation as well as to legacy devices. The RPS4000v2 acts as a redundant power

system in 12 VDC context and acts as a power bank in PoE (56 VDC) context.

Package Contents

This package includes:

• Redundant Power System and Power Bank RPS4000v2

• AC power cable

• RPS cable, 60 cm (23.6 in.),16 pin

RPS ports

Each RPS port on the RPS4000v2 can provide a maximum of 1440W at 56 VDC

and 200W at 11 VDC. Output power depends on the number of power supply

units (PSU) installed, and the settings of the Type selector and Current Share (CS)

selector on the back panel of the RPS4000v2.

To determine the RPS type for other switches, see the hardware installation guide

,which you can download by visiting netgear.com/support/download/.

Install the RPS4000v2

Install the RPS4000v2 in a standard 19-inch rack.

WARNING: Do not stack equipment, or place equipment in tight spaces or in

drawers. Be sure that your equipment is surrounded by at least 2 inches (5 cm) of

air space.

Insert a power supply unit

In models with more than one PSU, the PSUs are hot-pluggable.

1. If your switch functions with a single PSU only, disconnect the power cord

from the PSU and let the switch power down.

If your switch functions with more than one PSU, you do not need to power

down the switch and you can perform a hot swap.

2. Remove the PSU from the power module bay by moving the orange release

latch to the left and pulling the extraction handle.

3. Insert the replacement PSU into the power module bay, and gently push the

PSU into the bay until the latch locks.

CAUTION: When inserting the PSU, do not use unnecessary force. Doing so

can damage the connectors on the back of the PSU and on the midplane.

4. Connect the end of the power cord to the power receptacle on the PSU.

Produktspecifikationer

Varumärke:	Netgear
Kategori:	Inte kategoriserad
Modell:	RPS4000v2
Färg på produkten:	Antraciet
Bredd:	65 mm
Djup:	40 mm
Höjd:	120 mm
Kraftkälla:	Batterij/Accu
Anslutningsteknik:	Bedraad
Antal batterier/batterier som stöds:	3
Antal per paket:	1 stuk(s)
Trådlös teknik:	ZigBee
Batterityp:	AA
Uppmätta parametrar:	Light, Motion