NUVO NV-SUBAMP500-NA Bruksanvisning
Läs gratis den bruksanvisning för NUVO NV-SUBAMP500-NA (14 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 9 recensioner. Har du en fråga om NUVO NV-SUBAMP500-NA eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/14
Part Numbers
NV-SUBAMP100-xx
NV-SUBAMP200-xx
NV-SUBAMP500-xx
AMPLIFIER FEATURES
NV-SUBAMP100-xx
1 13 10
514 6 15 127
Fig. 1
NV-SUBAMP200-xx
19
5 12 11102071617
8
6 21415
Fig. 2
NV-SUBAMP500-xx
NOTE: Power mode, Volume control, Phase control, and Crossover control are accessed on the LCD display menu using the control knob.
19 2 3
219
12 111817 108 1020
Fig. 3
Installation Instructions
Nuvo In-Wall / In Ceiling Subwoofer Amplifiers
1507315 Rev A 20190328
2
1Status light
2LCD display
3Control knob
4Power mode switch
5Volume control
6Phase control
7Crossover control
8Low-level RCA input/
output jacks
9USB port
10 Voltage selector switch
11 Master power switch
12 Power cord inlet
13 WLS
14 High-level input
15
EQ selection:
A - NV-SUBIC8
B - NV-SUBIW8
C - SUBIWDUAL8
16 EQ mode
17 12 V DC trigger input/
output
18 IR
19 Power button
20 Sub terminal screws
21 Fuse
This instruction sheet covers the installation of the Nuvo In-Wall/In-Ceiling Subwoofer Amplifiers. These amplifiers offer a substantial amount of dynamic
power to increase the quality of your audio system.
UNDERSTANDING THE LCD PANEL FEATURES (FOR NV-SUBAMP500-XX MODELS)
Power Up Screen
Shows a message that the system is powering up.
Home Screen/Volume
Option for adjusting volume level.
Audio Mode Screen/Status
This setting has presets to put the amplifier into a mode that supports
your favorite listening environment. Choose one of the following options:
• Music
• Movie
• Bypass
Night Mode Status
This setting places a low sound threshold on the system for evening use.
• Off
• On
Speaker EQ Screen
Select one of the following modes:
• NVSUBIC8 1
• NVSUBIW8 2
• NVSUBIWDUAL8 3
• Flat
3
Crossover Main Screen
Crossover provides an option for a low pass filter for the amplifier. Choose
from one of the following options:
• LFE (Default setting)
• 40 - 250 HZ
Phase Screen
• 0-180
Lock Control Main Screen
Locks the menu for the amplifier controls to prevent accidental changes.
• Off
• On
Factory Reset
• Yes: Resets all amplifier controls to the default settings.
• No
Power Options Screen
This setting sets the power state. Choose from one of the following options:
• The amplifier is always on. This is the default setting.Switch:
• 12 V Trigger: The amplifier turns on automatically upon receiving a 12 V
input signal. When the 12 V signal is removed, the amplifier automatically
goes into standby mode.
• The amplifier turns on automatically upon receiving an Audio Sensor:
audio input signal. When the amplifier no longer receives a signal, it
automatically moves into a standby state after 15 minutes.
IR - Device ID
Assigns an IR ID between 1 and 4 to the amplifiers in the system.
• 1
• 2
• 3
• 4
Exit Menu Screen
• Press the knob to exit the menu for the controls and bring up the Home/
Volume screen.
Produktspecifikationer
| Varumärke: | NUVO |
| Kategori: | mottagare |
| Modell: | NV-SUBAMP500-NA |
Behöver du hjälp?
Om du behöver hjälp med NUVO NV-SUBAMP500-NA ställ en fråga nedan och andra användare kommer att svara dig
mottagare NUVO Manualer
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
mottagare Manualer
- Megasat
- Hirschmann
- SureCall
- Fender
- Shinybow
- Xoro
- Akg
- Oculus VR
- Creek
- Seco-Larm
- Jensen
- Glemm
- Soundstream
- Naim
- DAP
Nyaste mottagare Manualer
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025