NUVO Terrace 60/7747 Bruksanvisning
Läs gratis den bruksanvisning för NUVO Terrace 60/7747 (2 sidor) i kategorin Lättnad. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 3.7 stjärnor baserat på 10.5 recensioner. Har du en fråga om NUVO Terrace 60/7747 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS
REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should
a xture be hung on house electrical wires, nor should a swag
type xture be installed on a ceiling which contains a radiant type
heating system. Read instructions carefully. If you are unclear as to
how to proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this
xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all
parts are included as shown in gure. Be careful not to misplace
any of the screws or parts, which are needed to install this xture.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Fasten the cross bar onto the outlet box with the outlet
box screws.
STEP 2: Tie ground wire from outlet box and from xture to the
ground screw on the cross bar. Connect white wire from xture
to white wire (neutral wire) from supply circuit. Connect black
wire from xture to black wire (live wire) from supply circuit. Cover
connections using provided wire connectors.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground wire from
the xture (if supplied) around the green grounding screw, then
connect it to ground wire from the outlet box (if not xed on the
outlet box) using a wire connector (not supplied). If ground wire
from the xture is not supplied, wrap the ground wire (if not xed
on the outlet box) from the outlet box around the green grounding
screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture.
Identify which group your xture wire(s) falls into and connect the
wires according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire
is square shaped or ridged and the less tracer wire is round in
shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT twist wires
together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4 as above, and
check again for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside
outlet box. Place the xture body to the wall by aligning the
protruding mounting screws all the way through the wall plate and
tighten nial to the mounting screws until the xture body is held
rmly against the wall.
STEP 2: Secure the glass to the xture using the socket ring.
STEP 3: Install lamp (not included). Do not exceed the maximum
capacity recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-7747, 60-7748, 60-7749
ARTÍCULO Nº: 60-7747, 60-7748, 60-7749
ARTICLE N°: 60-7747, 60-7748, 60-7749
© Copyright 2023 Satco Products, Inc. 4/23 v1.0
Produktspecifikationer
| Varumärke: | NUVO |
| Kategori: | Lättnad |
| Modell: | Terrace 60/7747 |
Behöver du hjälp?
Om du behöver hjälp med NUVO Terrace 60/7747 ställ en fråga nedan och andra användare kommer att svara dig
Lättnad NUVO Manualer
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
4 April 2025
Lättnad Manualer
- Hoftronic
- Stairville
- SilverStone
- Ledino
- Envivo
- Maxcom
- Light & Motion
- Nexa
- Halo
- Steinhauer
- SIIG
- Golden Lighting
- Temde
- Stanley
- Gingko
Nyaste Lättnad Manualer
9 April 2025
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
5 April 2025
5 April 2025
5 April 2025