Oliveri LL117 Bruksanvisning
Läs gratis den bruksanvisning för Oliveri LL117 (4 sidor) i kategorin Sjunka. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 13 recensioner. Har du en fråga om Oliveri LL117 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
CUTTING THE BENCHTOP GENERAL INFORMATION
GRANITE SINK INSTALLATION INSTRUCTIONS
Please retain for consumer as care instructions are included
SEALANT
Oliveri recommends using the sealant strip (supplied with the sink), to seal between the sink and the bench
top. However, if silicone is used, it MUST be a “Neutral Cure” product – the use of “Acetic Cure” silicone
can damage or discolour the sink and will void warranty.
WASTE DISPOSAL UNITS
Waste disposal units can be fitted to Oliveri’s Granite Sinks. However, faulty or damaged waste disposal
units can cause vibration, which may lead to sink damage and will void warranty.
BASKET WASTE INSTALLATION
1 Fit the basket waste into the hole in the sink and then place the drain under the hole.
DO NOT USE SILICONE ADHESIVE.
2. Fasten the basket waste to the drain using a screw. Do not overtighten.
DRILLING THE TAP HOLE
Oliveri granite sinks with drainboards are provided with a pre-punched hole (picture A) placed on the front
and back of the sink in order to choose which side the bowls / drainer will sit. NOTE!
In order to avoid any possible damage to the sink, we strictly recommend to drill these pre-punched holes
using 35-37mm drill following the procedure shown in pictures B and C. We recommend using a diamond
coated drill to drill this hole.
Fig. A - Pre-punched tap holes Fig. B - Place the tool on the
pre-punched hole.
Fig. C - Drill the hole.
CHECK SPACE
Ensure there is adequate space for tapware (including a splashback if
specified). Check space for installation (underneath) and operation (above).
Particular care must be taken when a thick splash back is used (it may
interfere with tapware location and operation). Ensure the cabinet will not
foul the sink mounting flange or basins.
TEMPLATE
Cut out templates for your Oliveri sink are available online at oliveri.com.au.
Use the product model number to find the template. Some sink templates
apply to both left-hand and right-hand model sinks. Ensure template is
correct way around for your model.
MARK CUT OUT
Carefully mark out the template (or follow drawing instructions) making
allowance for any additional polishing back that is required after cutting.
Note: The template is the exact finished cut-out size required.
CUT & FINISH HOLE
Drill pilot holes to accept an appropriate cutting tool for the benchtop
material (wear suitable personal protection equipment). Cut inside the mark,
allowing sufficient room for any polishing back.
Note: Accuracy is essential to ensure the bowl / basin and accessories
fit correctly.
TRIAL FIT THE SINK
Carefully position the sink against benchtop to make sure it fits the cut out
correctly. If the fit is not correct, remove the sink and proceed with remedial
work. Perform another trial fit after corrections have been made.
IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING
Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in relation to goods
manufactured by it or their use and installation, is given in good faith and is believed by Tasman Sinkware to be
appropriate and reliable. However, any advice, recommendation, information, assistance or service is provided by
Tasman Sinkware without responsibility or liability.
Download cut out files (PDF, DWG or DXF) from oliveri.com.au
CHECK MODEL
The model number on the sink
packaging must match the model
of sink the customer ordered.
Do not install if incorrect.
AVOID CUTS
The perimeter and punch-outs on
the sink may contain sharp edges.
Handle the sink carefully to avoid
personal injury.
CHECK THE CONDITION
Inspect the sink for any visible
defects. Do not install the sink if
defects are found. Contact your
sink retailer / point of purchase.
AVOID BREAKAGES
Granite sinks can be broken if
proper care is not taken during
installation.
© Tasman Sinkware - TF158c Granite Sink Installation Instructions
Produktspecifikationer
| Varumärke: | Oliveri |
| Kategori: | Sjunka |
| Modell: | LL117 |
Behöver du hjälp?
Om du behöver hjälp med Oliveri LL117 ställ en fråga nedan och andra användare kommer att svara dig
Sjunka Oliveri Manualer
2 April 2025
4 Mars 2025
21 September 2024
21 September 2024
21 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
Sjunka Manualer
- Franke
- Kohler
- Saro
- Shaws
- CDA
- Eagle Group
- Schock
- Caple
- Hendi
- Artusi
- Tot Mate
- Seima
- Teka
- Rangemaster
- Bartscher
Nyaste Sjunka Manualer
9 April 2025
8 April 2025
8 April 2025
31 Mars 2025
30 Mars 2025
26 Mars 2025
3 Mars 2025
28 Januari 2025
27 Januari 2025
26 Januari 2025