Oricom BC200 Bruksanvisning
Oricom
Batteriladdare
BC200
Läs gratis den bruksanvisning för Oricom BC200 (1 sidor) i kategorin Batteriladdare. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 13 recensioner. Har du en fråga om Oricom BC200 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
- 1 - - 2 - - 3 - - 4 -
Multi-View Display Description
Note:
1) Do not charge a lithium battery without a battery management system
(BMS) protection board incorporated in the lithium battery.
2) Charge batteries with a capacity of less than 20AH at the minimum
charging current setting.
Made in PRC
Multi-view display alternates between current battery voltage, charge current,
charge quantity, BC200 inside temperature, repair process status, and fully
charged status.
Symbols:
FUL battery fully charged
END repair process complete. To continue with trickle charge, press mode
button to select correct battery type.
OFF Standby mode, clamps are not connected.
Flt. The battery is defective, or unable to be charged. Check the battery at
your local battery supplier.
Winter temperature symbol <10
º
C. (ref. only)
Summer temperature symbol > 28
º
C. (ref. only)
Product Overview
1. Adjust and select the appropriate charging current for your battery.
2. Connect the red positive clamp to battery positive, then the black negative
clamp to battery negative.
3. Connect the charger to the mains power.
AC 220-240V 50~60Hz
Step 3 Step 4
3A/5A
20A/10A
10A/5A
Step 1 Step 2
Charging Your Battery
Repair Process Complete
Battery Fully ChargedStandby Low Voltage
Charge Current
Battery VoltageBattery Voltage
V
Charger Inside TemperatureSummer Mode
Winter Mode
Charge Quantity
Wrong polarity Check polarity of the battery clamps.
The battery is defective, or unable to be charged.
Check the battery at your local battery supplier.
Bad connection Check the connection between the
charger and the battery.
Repair Mode. An advanced battery recovery mode
for repairing and storing old, idle, damaged, stratified
and sulfated batteries. The maximum repair time is
24 hours. Only for lead-acid batteries. Can not repair
badly damaged batteries.
7-Stage Charging Process
Stage 1: Battery desulphation » this stage only for car mode
Stage 2: Soft start charging
Stage 3: Bulk charging
Stage 4: Absorption charging
Stage 5: Battery test
Stage 6: Recondition charging
Stage 7: Float & maintenance charging
Battery
Capacity
(Ah)
50(Ah)
120(Ah)
150(Ah)
400(Ah)
1000(Ah)
12V 5A
6.5 H 3.1 H / 10 H 6.5 H 3.1 H
7.5 H 4.2H 25 H 15 H 7.5 H
9.5 H 5.0 H 31.5 H 19 H 9.5 H
25 H 12.5 H / / 25 H
/ 38 H / / 76 H
15 H
19 H
200(Ah)
12.5 H 6.5 H / 25 H 12.5 H25 H
/
/
Charging Time(H)
12V 10A 12V 20A 24V 3A 24V 5A 24V 10A
Estimated Charging Time
Note: The estimated charging time is for reference only.
1. Supports Lithium,Lead-acid(AGM,GEL,SLA,Flooded,WET,EFB,etc.) and
LiFePo4 batteries.
2. Full automatic microprocessor control. 7-stage charging program
provides the most efficient battery charging.
3. Charging voltage automatically adapts to temperature to prevent over-or
under-charging.
4. Repair function to repair old, weak and idle batteries. For Lead-acid
batteries only.
5. Overcharge protection, reverse polarity protection, and short circuit
protection.
6. LCD screen showing voltage, current, battery power, temperature etc.
7. Selectable charge current.
8. Auto-memory function will return to the last mode when connected.
Features
12V,24VApplicable battery voltage:
2VMinimum Start Volt:
Lithium, LiFePO4, Lead-acid (AGM, GEL,
EFB,MF, FLOODED, VRLA, SLA, WET, etc.)
Applicable battery type:
Max 20A(12V),Max 10A(24V)
Charging Current:
Input Power with Load: Max 280W
Dimensions: 158*90*50mm
Net weight: 470g
220-240V~50/60HzAC Input Voltage:
BC200
Model:
Specifications
Typical Battery Voltages
12V Lead-acid (AGM, GEL, EFB,MF,
FLOODED, VRLA, SLA, WET, etc...)
24V Lead-acid (AGM, GEL, EFB,MF,
FLOODED, VRLA, SLA, WET, etc...)
Battery Type Voltage
12V LITHIUM
24V LITHIUM
Max 14.7V/ 12.6V
Max 29.4V/ 25.2V
12V LIFEPO4
24V LIFEPO4
Max 14.7V
Max 29.4V
Max 14.6V
Max 29.2V
- 5 - - 6 - - 7 -
Express Warranty (Australia)
This Express Warranty is provided by Oricom International
Pty Ltd ABN 46 086 116 369, Unit 1, 4 Sovereign Place, South Windsor
NSW 2756, herein after referred to as “Oricom”.
Oricom warrants that the product is free from defects in materials or
workmanship during the Express Warranty Period. This Express Warranty
does not extend to any product from which the serial number has been
removed or was purchased outside of Australia.
The benefits of this Express Warranty are in addition to other rights and
remedies you may have under the Australian Consumer Law. Our goods
come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure. In the event of a minor failure, Oricom reserves the right to
choose to repair or replace the product.
The Express Warranty Period will be a period of 3 Years beginning on the
date of purchase of the product evidenced by your dated sales receipt. You
are required to provide proof of purchase as a condition of receiving
Express Warranty services.
You are entitled to a replacement product or repair of the product at our
discretion according to the terms and conditions of this document if your
product is found to be faulty within the Express Warranty Period. This
Express Warranty extends to the original purchaser only and is not
transferable.
Products distributed by Oricom are manufactured using new materials or
new and used materials equivalent to new in performance and reliability.
Spare parts may be new or equivalent to new. Spare parts are warranted to
be free from defects in material or workmanship for thirty (30) days or for
the remainder of the Express Warranty Period of the Oricom branded
product in which they are installed, whichever is longer. During the Express
Warranty Period, Oricom will where possible repair and if not replace the
faulty product or part thereof. All component parts removed under this
Express Warranty become the property of Oricom. In the unlikely event that
your Oricom product has a recurring failure, Oricom may always, subject to
the Competition and Consumer Act 2010, at its discretion, elect to provide
you with a replacement product of its choosing that is at least equivalent to
your product in performance.
No change to the conditions of this Express Warranty is valid unless it is
made in writing and signed by an authorised representative of Oricom.
Oricom will not be liable under this Express Warranty, and to the extent
permitted by law will not be liable for any defect, loss, damage or injury
arising out of or in connection with a:
1. Failure by you to adhere to the warnings and follow the instructions set
out in this user guide for the proper installation and use of the product;
2. Wilful misconduct or deliberate misuse by you of the product;
3. Any external cause beyond our control, including but not limited to power
failure, lightning or over voltage; or
4. Modification to the product or services carried out on the product by
anyone other than Oricom or Oricom’s authorised service provider.
How to make a claim under your Express Warranty in
Australia
Oricom has a simple warranty process for you to follow:
· Please call or email our Customer Support Team, (02) 4574 8888 or
support@oricom.com.au.
· A Customer Support Team member will verify after troubleshooting with
you if your product qualifies under warranty. If so, they will give you a
Product Return Authorisation number.
· We will then email or fax a Return Authorisation form and a Repair Notice
(if necessary), together with instructions on how to return the goods for
warranty service.
Please note that if a Customer Support Team member advises that your
product does not qualify for return, this warranty does not apply to your
product. Products that are authorised to be returned to Oricom in Australia
must include all of the following:
· A completed Return Authorisation form
· A copy of your Proof of Purchase (please keep your original copy)
· The faulty product, including all accessories.
Send the approved returns to:
Oricom International Pty Ltd
Locked Bag 658
South Windsor NSW 2756 Australia
Please note that this Express Warranty excludes expenses incurred by you
in returning any faulty product to us. You must arrange and pay any
expenses incurred (including postage, delivery, freight, transportation or
insurance of the product) to return the faulty product to us, however, we will
arrange delivery of the repaired or replaced faulty product to you.
Important Information
Repair Notice
Please be aware that the repair of your goods may result in the loss of any
user generated data (such as stored telephone numbers, text messages and
contact information). Please ensure that you have made a copy of any data
saved on your goods before sending for repair. Please also be aware that
goods presented for repair may be replaced by refurbished goods or parts
of the same type rather than being repaired.
Oricom have a trained and dedicated team of Customer Support
Representatives, each with the knowledge and resources to assist in
answering your questions quickly and efficiently.
Oricom Support - Australia
For all product enquiries, troubleshooting or to discuss the range of Oricom
products, feel free to contact Oricom or visit our website for answers to
frequently asked questions.
(02) 4574 8888
Monday - Friday 8am - 6pm AEST
Email: support@oricom.com.au
www.oricom.com.au
Oricom Support - New Zealand
0800 674 266
Monday - Friday 11am - 7pm NZST
Email: support@oricom.co.nz
- 8 -
ORICOM CUSTOMER SUPPORT
1. Do not charge a lithium battery without a battery management system
(BMS) protection board incorporated in the lithium battery. Before using
the BC200 to charge a lithium battery confirm a BMS is fitted to your
battery or a hazard may occur.
2. Batteries below 20AH should be charged with the minimum current
setting.
3. The charger is designed for 12V and 24V Lithium,Lead-acid and LiFePO4
batteries.
4. Check battery specifications before use.
5. Only use in well ventilated conditions to prevent flames and sparks.
6. Do not expose charger to the sun, or in a high temperature environment.
7. Battery acid is corrosive. Rinse immediately with water if acid comes into
contact with skin or eyes.
8. Do not charge a frozen or damaged battery.
9. Do not charge non-rechargeable batteries.
10. Do not place the charger on the battery while charging.
11. Be extra cautious to reduce risk of dropping a metal tool on the battery.
It might spark or short-circuit the battery that may cause explosion.
12. When working with a lead-acid battery, remove personal metal items.
13. In order to reduce risk of electric shock, unplug charger from AC outlet
before doing any maintenance or cleaning .
14. Keep away from children, this is not a toy.
Warnings and Safety Precautions
1
2
3
4
5
Charge current switch. 3 levels: 5A(12V)/3A(24V), 10A(12V)/5A(24V),
20A(12V)/10A(24V).
6
Used to select the charging mode
For charging 12V or 24V batteries or Lithium batteries with Battery
Management Systems (BMS).
For ordinary lead-acid batteries/maintenance-free batteries, including;
AGM, GEL, SLA, WET, DEEP CYCLE, EFB, Calcium, etc.
For charging 12V or 24V LiFePO4 batteries.
Lead-acid batteries only, for repair of old or heavily discharged
batteries. Can not repair severely damaged batteries.Note:
Auto-Memory: The charger has a memory function and will automatically
select the last mode.
BC200
5A/10A
3A/5A 10A/20A
Smart Charger
LITHIUM AGM/LEAD LiFePO4 REPAIR
12V 24V
10A20A
MODE
Battery Type
1
2 3 4 5
6
12V/24V Battery Charger and Maintainer
USER MANUAL
BC200
Battery Capacity
4. Select the corresponding mode according to the battery type. (The charger
automatically recognises the battery voltage and selects 12V or 24V.)
SAA-230820-EA
Recommended operating
temperature:
-25 to +60 °C
Produktspecifikationer
| Varumärke: | Oricom |
| Kategori: | Batteriladdare |
| Modell: | BC200 |
Behöver du hjälp?
Om du behöver hjälp med Oricom BC200 ställ en fråga nedan och andra användare kommer att svara dig
Batteriladdare Oricom Manualer
16 September 2024
Batteriladdare Manualer
- Targus
- IEB
- Inateck
- Mercury
- NOCO
- Venom
- Fronius
- Festool
- Terratec
- Goobay
- MIDAC
- Monacor
- Tecxus
- FlinQ
- Lindy
Nyaste Batteriladdare Manualer
15 September 2025
14 September 2025
12 September 2025
6 September 2025
5 September 2025
2 September 2025
2 September 2025
2 September 2025
2 September 2025
29 Augusti 2025