Ozito SCMS-8STANDU Bruksanvisning
Läs gratis den bruksanvisning för Ozito SCMS-8STANDU (2 sidor) i kategorin Sågmaskin. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 8 recensioner. Har du en fråga om Ozito SCMS-8STANDU eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
ASSEMBLY OF STAND
SLIDING
COMPOUND MITRE
SAW & STAND
210mm (8¼”)
ORIGINAL INSTRUCTIONS
STAND ASSEMBLY
STAND
FASTENERS
The stand is constructed by assembling each half of the structure and
then joining them together.
7 Bolt Small - 36 pc
8 Washer Small - 36 pc
9 Nut Small - 36 pc
10 Rubber Foot - 4 pc
11 Bolt Large with Rubber
Stopper - 4 pc
12 Saw Mounting Bolts - 4 pc
1 Short Upper Support - 2 pc
2 Short Lower Support - 2 pc
3 Long Upper Support - 2 pc
4 Long Lower Support - 2 pc
5 Upper Leg - 4 pc
6 Lower Leg - 4 pc
1197 10
16
2 3 4 5
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x4 x4
1 Remove the stand components
from the box and group matching
pieces together. Check that you
have all the contents listed to the
left.
Note: All upper members can be
identied by the 2 holes very close
together.
2 Lay two upper and lower legs on
the ground aligning 2 of the bolt
holes, parallel to each other.
The upper leg sits outside the
lower leg.
3 Place one long lower support
in between the legs and align
the bolt holes. The side support
should have its lip on the high side
(facing up) and should sit inside
the legs.
Ensure the lip with the lengthened
bolt holes is facing upwards.
4 Once aligned, insert small bolts
into the 2 aligned holes at both
sides of the lower support. Insert
the bolt from the outside and
screw a small washer and nut
onto each bolt to secure (only
hand tight at this initial stage).
5 Place one long upper support on
the of the legs at the top outside
(This will ensure the mounting
holes will align correctly once
assembled)
Insert a bolt from the outside into
the 2 aligned holes at either side
of the upper support and hand
tighten a small washer and nut
onto each.
6 At this stage your frame should
look like this.
128
SCMS-8STANDU
Art.-No.: 30.003.16 I.-No.: 11017
Produktspecifikationer
| Varumärke: | Ozito |
| Kategori: | Sågmaskin |
| Modell: | SCMS-8STANDU |
Behöver du hjälp?
Om du behöver hjälp med Ozito SCMS-8STANDU ställ en fråga nedan och andra användare kommer att svara dig
Sågmaskin Ozito Manualer
24 December 2024
6 Oktober 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
21 September 2024
10 September 2024
6 September 2024
Sågmaskin Manualer
- Challenge
- Hitachi
- Sterwins
- Kraftronic
- Einhell Bavaria
- Einhell
- Prowork
- Power Smart
- Workzone
- Proviel
- MTM
- Tacklife
- Fuxtec
- Huvema
- Troy-Bilt
Nyaste Sågmaskin Manualer
3 April 2025
3 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
29 Mars 2025
29 Mars 2025