PAC AVS-21 Bruksanvisning
PAC
Inte kategoriserad
AVS-21
Läs gratis den bruksanvisning för PAC AVS-21 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 9.5 recensioner. Har du en fråga om PAC AVS-21 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
Rev. 040815
AVS-21
Two-Way Audio/Video Switcher
P ifi A C ti
AVS-21
Two-Way Audio/Video Switcher
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
Rev. 040815
P ifi A C ti
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
The AVS-21 is a two way A/V switcher designed for use with any of the PAC BCI interfaces. The AVS-21
can also be used as a stand alone unit for any application requiring a two way A/V switch.
Introduction & Features
Important Notes
1. The A/V output will pass the A/V 1 input at all times until the module is triggered.
2. The module can be triggered by either a positive or negative trigger, however when used with a BCI module it will always be a positive
trigger.
1. The black and red wires in the 2-pin plug are the trigger wires. If you are using the AVS-21 with a BCI interface you will connect the black wire
to ground and the red wie to the red programmable output wire on the BCI interface. If you are using the AVS-21 in any other application,
you can connect the red and black trigger wires to best suite your needs.
2. Connect the RCAs labeled “A/V1 IN” to the primary A/V source.
3. Connect the RCAs labeled “A/V2 IN” to the secondary A/V source.
4. Connect the RCAs labeled “A/V OUT” to the screen/head unit.
Installation Steps
The AVS-21 is a two way A/V switcher designed for use with any of the PAC BCI interfaces. The AVS-21
can also be used as a stand alone unit for any application requiring a two way A/V switch.
Introduction & Features
Important Notes
1. The A/V output will pass the A/V 1 input at all times until the module is triggered.
2. The module can be triggered by either a positive or negative trigger, however when used with a BCI module it will always be a positive
trigger.
1. The black and red wires in the 2-pin plug are the trigger wires. If you are using the AVS-21 with a BCI interface you will connect the black wire
to ground and the red wie to the red programmable output wire on the BCI interface. If you are using the AVS-21 in any other application,
you can connect the red and black trigger wires to best suite your needs.
2. Connect the RCAs labeled “A/V1 IN” to the primary A/V source.
3. Connect the RCAs labeled “A/V2 IN” to the secondary A/V source.
4. Connect the RCAs labeled “A/V OUT” to the screen/head unit.
Installation Steps
Produktspecifikationer
| Varumärke: | PAC |
| Kategori: | Inte kategoriserad |
| Modell: | AVS-21 |
Behöver du hjälp?
Om du behöver hjälp med PAC AVS-21 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad PAC Manualer
10 Mars 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
12 Februari 2025
12 Februari 2025
Inte kategoriserad Manualer
- Etna
- Ankarsrum
- Hanseatic
- Pattfield
- Jungle Gym
- Eminent
- Dynaudio
- Cosori
- Foster
- Metapace
- Empress Effects
- Peerless-AV
- Reltech
- Champion
- Vipack
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025