PAC RadioPRO 3 RP3-GM11 Bruksanvisning

PAC Inte kategoriserad RadioPRO 3 RP3-GM11

Läs gratis den bruksanvisning för PAC RadioPRO 3 RP3-GM11 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 6.5 recensioner. Har du en fråga om PAC RadioPRO 3 RP3-GM11 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

RP3-GM11

Radio Replacement Interface for General Motors Vehicles

Paciﬁ c Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 120513

P ifi A C ti

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP3-GM11 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios. Using

this interface will retain factory features such as Warning Chimes and BOSE® ampliﬁ er (Standard or Premium) when the original

radio is removed. The RP3-GM11 provides data bus driven outputs such as retained accessory power (RAP), vehicle speed

sensor (VSS), illumination, reverse trigger and parking brake. The RP3-GM11 also provides a secondary output for adding an

optional PAC Steering Wheel Control (SWC) retention interface (SWI-RC, SWI-PS, SWI-JACK, SWI-ECL2 or SWI-X). Rear Seat

Controls (RSC) if equipped will also be retained with the SWI interface.

1. When used in Non-BOSE® applications simply cut off the RCA connectors and connect the remaining wires to the aftermarket

radios high level speaker outputs.

2. For BOSE® systems, the recommended line level input is between 2-4 volts from the aftermarket radio.

3. RSC buttons that are identical to the SWC will mimic the SWC one for one

4. To prevent over driven audio when installing the interface into a vehicle with a BOSE® system, and the aftermarket radio does

not have low level outputs, then an LOC (part # SOEM-4 or LP3-4) is recommended to match the input voltage or you can create

an audio attenuation circuit (see diagram 2 below for audio attenuation wiring).

5. Use the 4 position selector switch located on the side of the interface to select the best chime output volume for your speciﬁ c

installation .

Red / White Parking Brake

Output (-)*

Purple / White Vehicle Speed

Output*

Blue / White Amp Turn On Input

Red Accessory Output

(10 amp)

Orange / White Illumination Output

(+)*

Green Reverse Output (+)*

Interface Connector

Yellow Battery +12v

Black Ground

Blue Antenna On Input

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

Vehicle Connector

Audio Attenuation Circuit for RP3-GM11

One channel shown

*Not all radios will have these

connections. Please insulate

these wires when not used.

Diagram 1

Chime Volume Adjustment

Cut for Non-Bose systems

Aftermarket Radio

Connections

To Vehicle

Connector

Connect to SWC

Interface. Program

for Version 2.

To optional SWC interface

Acc On

LED

Produktspecifikationer

Varumärke:	PAC
Kategori:	Inte kategoriserad
Modell:	RadioPRO 3 RP3-GM11
Enhetsplacering:	Vrijstaand
Typ av operation:	Rotary, Touch
Färg på produkten:	Wit
Dörrgångjärn:	Rechts
Inbyggd display:	Ja
Värmekälla:	Electrisch
Bredd:	598 mm
Djup:	599 mm
Höjd:	842 mm
Typ av laddare:	Voorbelading
Torksystem:	Condensatie
Fördröjd starttimer:	Ja
Startfördröjning:	24 uur
Barnlås:	Ja
Torkningsklass:	B
Cykelns längd:	126 min
Ljudnivå:	64 dB
Anti-veck funktion:	Ja
Energie-efficiëntieklasse:	B
Årlig-energiförbrukning:	557 kWu
Strömförbrukning (i standby):	0.5 W
Strömförbrukning (när avstängd):	0.1 W
Belysning i trumma:	Ja
Inbyggt kondensavlopp:	Ja
Anti-veck cykel:	120 min
Nominell kapacitet:	8 kg
Type beeldscherm:	LED
Torkprogram:	Wool, Mix, Sport, Quick