Panduit CT-1006 Bruksanvisning
Sidor 2 Engels Handverktyg
Läs bruksanvisningen för Panduit CT-1006 gratis online eller ladda ner PDF:en. 28 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
©
Panduit Corp. 2018
Page: 1of 2
CONTROLLED CYCLE FERRULE CRIMPING TOOLS
OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS
1. With the handles in
the open position,
insert the ferrule
into the opening at
the top of the tool.
Make sure that the
ferrule insulation or
flared end is up
(see Figure 2). Do
not allow insulation
to be inserted into
crimp die. Close
handles until dies
just slightly crimp
ferrule.
2. Insert the stripped wire into the ferrule until the wire
stops. Refer to product packaging for wire strip length.
3. Crimp the ferrule by closing the handles until the
controlled cycle mechanism releases. Upon release,
the handles will open automatically and the crimped
ferrule can be removed.
1. With the handles in
the open position,
insert the ferrule
into the crimp
pocket. Make sure
that the ferrule is
inserted fully into
the crimp die (see
Figure 4).
2. Insert the stripped
wire into the ferrule
until the wire stops.
Refer to product
packaging for wire
strip length.
3. Crimp the ferrule by closing the handles until the
controlled cycle mechanism releases. Upon release,
the handles will open automatically and the crimped
ferrule can be removed.
NOTE:Crimp entire uninsulated ferrule length. This may
require additional crimps.
CT-1002, CT-1003 and CT-1004 TOOLS
CT-1005 and CT-1006 TOOLS
Cushioned handle grips
CRIMP POCKET for Insulated
and Non-Insulated Ferrules. Part
usage dependent on wire range.
Refer to product packaging for
proper wire combination.
Controlled cycle mechanism
prevents tool from opening
before crimp cycle is complete.
Manual release lever, push
forward in the event that
controlled cycle mechanism
must be released.
Fig. 1
Fig. 3
Fig. 4
Fig. 2
Stripped
Wire
Crimp Die
Die Closure Alignment
(not a crimp pocket)
Controlled cycle mechanism pre-
vents tool from opening before
crimp cycle is completed.
Manual release lever, push
forward in the event that
controlled cycle mechanism
must be released.
Cushioned handle grips
Ferrule
Insulation
s
ection
Ferrule -
Metal crimp
section
S
tripped
Wire
CRIMP POCKETS for Ferrule
terminals. Refer to product
packaging for wire range and
proper crimp pocket. Crimp
pockets are identified with
applicable wire range.
Ferrule - Wire
crimp section
Ferrule Insulated
section
CT-1002, CT-1003, CT-1004,
CT-1005 and CT-1006
PA24073A01
REV: 04 2-2018
E-mail:
For Technical Support:
1-800-777-3300
www.panduit.com
CAUTION:
Verify power is “OFF” before working
on wiring with these tools.
The plastic grips are for the user’s
comfort, and are not intended
to insulate against electrical shock
while working on live electrical circuits.
Produktspecifikationer
| Varumärke: | Panduit |
| Kategori: | Handverktyg |
| Modell: | CT-1006 |
| Enhetsplacering: | Ingebouwd |
| Typ av operation: | Touch |
| Färg på produkten: | Black, Stainless steel |
| Inbyggd display: | Ja |
| Timer: | Ja |
| Bredd: | 870 mm |
| Djup: | 510 mm |
| Höjd: | 95 mm |
| Barnlås: | Ja |
| Förpackningens vikt: | 23600 g |
| Förpackningens bredd: | 950 mm |
| Djuppackning: | 580 mm |
| Förpackningshöjd: | 170 mm |
| Brännare/kokzonseffekt 2: | 2300 W |
| Brännare/kokzonseffekt 3: | 1400 W |
| Brännare/kokzonseffekt 1: | 2300 W |
| Antal brännare/kokzoner: | 3 zone(s) |
| Typ av häll: | Inductiekookplaat zones |
| Brännare/kokzon typ 1: | Regulier |
| Brännare/kokzon typ 2: | Groot |
| Typ av brännare/kokzon 3: | Sudderen |
| Lätt att städa: | Ja |
| Antal gasbrännare: | 0 zone(s) |
| Antal elektroniska kokzoner: | 3 zone(s) |
| Kontrollposition: | Boven voorzijde |
| Ansluten last (elektrisk): | 6700 W |
| Installationsfackets bredd: | 860 mm |
| Installationsfack djup: | 490 mm |
| Ansluten last (gas): | - W |
| Boost funktion: | Ja |
| Restvärmeindikator: | Ja |
| Ramtyp: | Full trim |
| Pansigenkänning: | Ja |
| Ramfärg: | Roestvrijstaal |
| Strömkälla brännare/kokzon 1: | Electrisch |
| Strömkälla brännare/kokzon 2: | Electrisch |
| Strömkälla brännare/kokzon 3: | Electrisch |
| Kookzone 1 boost: | 3000 W |
| Kookzone 2 boost: | 3000 W |
| Placera brännare/kokzon 1: | Links voor |
| Diameter brännare/kokzon 1: | 200 mm |
| Placera brännare/kokzon 2: | Midden achter |
| Brännare/kokzons diameter 2: | 250 mm |
| Placera brännare/kokzon 3: | Rechts voor |
| Brännare/kokzons diameter 3: | 160 mm |
| Kokzon 1 form: | Rechthoekig |
| Kokzon 2 form: | Rechthoekig |
| Kokzon 3 form: | Rechthoekig |
Behöver du hjälp?
Om du behöver hjälp med Panduit CT-1006 ställ en fråga nedan och andra användare kommer att svara dig
Handverktyg Panduit Manualer
Panduit CT-1004 Bruksanvisning Panduit CT-1090 Bruksanvisning Panduit CT-2600/LBT Bruksanvisning Panduit CT-3001/STBT Bruksanvisning Panduit CT-3001/CCPBT Bruksanvisning Panduit CT-2920/CCPBT Bruksanvisning Panduit CT-2940/STBT Bruksanvisning Panduit CT-3980/BT Bruksanvisning
Alla Panduit Handverktyg manualer
Populära i Handverktyg
Handverktyg Manualer
Nyaste Handverktyg Manualer
Bosch PTA 1000 Bruksanvisning Klein Tools VDV120-006 Bruksanvisning Klein Tools VDV110-295 Bruksanvisning Klein Tools VDV110-261 Bruksanvisning Klein Tools 89030 Bruksanvisning Klein Tools VDV110-061 Bruksanvisning Klein Tools VDV110-095 Bruksanvisning Klein Tools VDV120-005 Bruksanvisning Klein Tools T1710 Bruksanvisning Wera Bit-Check 12 Bruksanvisning