Panduit CT-200 Bruksanvisning
Panduit
Inte kategoriserad
CT-200
Läs gratis den bruksanvisning för Panduit CT-200 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 5 recensioner. Har du en fråga om Panduit CT-200 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
CT-200
CRIMPING TOOL
OPERATION INSTRUCTIONS
Page: 1 of 1
PA24428A01
REV.: 02 6-2018
OPERATION INSTRUCTIONS
© Panduit Corp. 2018
CT-200
Technical Support:
1-800-777-3300
E-mail:
techsupport@panduit.com
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CRIMP POCKET for Pan-Term non-
insulated terminals, disconnects,
splices and wire joints.
The 12-10 pocket is for No. 12 to No. 10
solid or stranded wire; the 22-14 pocket
is for No. 22 to No. 14 solid or stranded
wire. The crimp should be centrally
located on the barrel with the indenter
on the seam, and the dies fully closed
for best results.
This tool is made of hardened steel and
is protected with a light coat of oil.
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combination.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
CRIMP POCKET
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of the
metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
CAUTION:
Verify power is “OFF” before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
www.panduit.com
Produktspecifikationer
| Varumärke: | Panduit |
| Kategori: | Inte kategoriserad |
| Modell: | CT-200 |
Behöver du hjälp?
Om du behöver hjälp med Panduit CT-200 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Panduit Manualer
1 Januari 2025
1 Januari 2025
1 Januari 2025
1 Januari 2025
30 December 2025
30 December 2025
30 December 2025
30 December 2025
15 December 2024
15 December 2024
Inte kategoriserad Manualer
- Egnater
- Brentwood
- Fujitsu
- Friedland
- QUIO
- OK
- META
- IQAir
- Bestar
- Alpen Kreuzer
- Constructa
- Mobicool
- Blomberg
- Deutz
- TEF
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025