Panduit NetKey NKSPB Bruksanvisning
Panduit
ej kategoriserat
NetKey NKSPB
Läs gratis den bruksanvisning för Panduit NetKey NKSPB (2 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 3.8 stjärnor baserat på 2 recensioner. Har du en fråga om Panduit NetKey NKSPB eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2017
NK194D
Page 2 of 3
NetKey
Network Components
Keystone Cabling System
TERMINATION INSTRUCTIONS
Signal Ground
RCA Module
S-Video Module
Chrominance
Chrominance Ground
Luminance Ground
Luminance
Remove approximately 1" of cable jacket. (CAUTION: Do not damage conductors.) Fan out twisted pairs for
termination.
S-Video Module RCA Module
STEP 1
Use the PDT110 Single Wire Punchdown tool to punchdown conductors in the orientation shown.
Modules should appear as shown below when terminated.
Signal
STEP 2
Signal and Signal Ground use one twisted pair
Chrominance and Chrominance Ground use one twisted pair
Luminance and Luminance Ground use one twisted pair
NetKey RCA and S-Video
110 Style Punchdown Modules
Part Numbers: NKSPM**, NKRPM***, NKSPB
(UTP Cable)
White / Blue
Blue
White / Orange
Orange
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2017
NK194D
www.panduit.com
Page 3 of 3
Use the optional NKSPB NetKey 110PD Module Puck to align and hold the module for
termination to the connector block.
Set fully assembled module into puck, aligning flexible snap on module with screwdriver
slot on puck. Snap in place. Do not press on the connector to snap in place.
To remove module from puck, place index finger on the opposite side of the screwdriver
slot and thumb on the NetKey housing, not on the punch-down block, otherwise module
will be damaged. Apply pressure to module flexible snap, tilt module, and remove. Using
a small screwdriver to remove the module is optional.
Screwdriver is optional
to remove NetKey
module from puck.
OPTIONAL STEP
Install the P110RC2 wire retention cap onto the connector block.
Modules should appear as shown below when completed.
STEP 3
S-Video Module RCA Module
INSTALLATION TIPS:
1. Pan-Punch
product terminates most 22-26 AWG solid or stranded IWC wire with a 0.050" (1.27mm) max. o.d., either PVC or plenum rated.
2. Never install wire into a slot previously used for a larger gauge.
3. Be careful to strip back cable jacket only as required for termination.
4. Use care to maintain pair twists to within 0.50 inches (13mm) of the termination strip.
5. When stripping cable jacket, be careful not to cut the insulation on the individual wires.
6. Avoid sharp bends when routing cable.
NKSPB
Flexible
Screwdriver
snap
slot
Screwdriver
slot
MODULE INSTALLATION
MODULE REMOVAL
Produktspecifikationer
| Varumärke: | Panduit |
| Kategori: | ej kategoriserat |
| Modell: | NetKey NKSPB |
Behöver du hjälp?
Om du behöver hjälp med Panduit NetKey NKSPB ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Panduit Manualer
28 Juni 2025
ej kategoriserat Manualer
- AEG
- Curtis
- Antec
- Gamdias
- Lenovo
- IOGEAR
- Panasonic
- Axis
- Sommer
- Sony
- TCL
- Emko
- Audio-Technica
- LaCie
- Trotec
Nyaste ej kategoriserat Manualer
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025
29 Juni 2025