Panduit TGJT Bruksanvisning

Panduit Inte kategoriserad TGJT

Läs gratis den bruksanvisning för Panduit TGJT (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 9.5 recensioner. Har du en fråga om Panduit TGJT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

FIGURE 1:

1. Operator should manually

wire the required TG style

Jack Wire Cap for the desired

application. Wires must be

separated and slightly down

over the individual pocket

divider wedges. Depress

strain relief collar to secure

cable.

MADE IN COSTA RICA

TGJT PA25217A01

Rev. 03 2-2016

OPERATING INSTRUCTIONS

Page: 1 of 2

FIGURE 2:

2. Insert the prepared Wire Cap

into the Wire Seating/Cutting

side of the TGJT Tool. This

side pocket properly aligns

and holds the prepared Wire

Cap in place. Make sure all

twisted pairs of wires are out

to the sides of the Wire Cap

for proper cutting (refer to

Figure 1). The ramp of the

Wire Cap must be pointing

upward and be inserted

into the groove in the upper

Cutter Blade Anvil.

FIGURE 3:

3. Pull the handle and the mechanism seats the conductors into

the Wire Cap. At the same time, the Cutter Blades trim the

wires nearly flush with the side faces of the Wire Cap.

4. Keeping the handles closed, slide the Wire Cap up and out of

the tool. All wires should cut cleanly.

www.panduit.com

Technical Support: Panduit USA

888-506-5400, Ext. 86914

E-mail: techsupport@panduit.com

NOTE: STRIPPED WIRES MUST BE LONG ENOUGH TO

STICK OUT OF THE SIDES OF THE WIRE CAP.

Refer to product installation instructions listed above

for recommended wire strip lengths.

RAMP

ANVIL GROOVE

NOTE: IF THE WIRES DO NOT CUT CLEANLY OR THE WIRE

CAP DOES NOT WANT TO COME OUT, EXAMINE THE

CUTTER BLADE EDGE SURFACES AT THE NEXT

OPENING CYCLE. IF BLADES ARE NICKED OR

APPEAR WORN, REPLACE THEM WITH THE BLADE

REPLACEMENT KIT.

TGJT TOOL

DIVIDER

WEDGES

Refer to product installation instructions for

TX6 PLUS and TX5e UTP Jack Modules: PN403M

and TX6A 10Gig UTP Jack Modules: PN511E

for wiring instructions.

STRAIN

RELIEF

COLLAR

TG STYLE JACK TERMINATION TOOL

FOR INSTALLING ALL

TG STYLE COPPER JACK MODULES

Part No.: TGJT

Produktspecifikationer

Varumärke:	Panduit
Kategori:	Inte kategoriserad
Modell:	TGJT
Vikt:	785 g
Bredd:	244 mm
Djup:	244 mm
Höjd:	51 mm
Ethernet LAN:	Ja
Antal HDMI-portar:	1
Antal Ethernet LAN (RJ-45)-portar:	1
DVI-D-portar:	1
Stöder Windows:	Windows 10
Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ A:	4
Processoruttag:	Socket AM4
Processorfabrikant:	AMD
Maximalt internminne:	128 GB
Ljudutgångskanaler:	- kanalen
Chipset moderkort:	AMD B550
Antal portar USB 3.2 Gen 2 (3.1 Gen 2) Typ A:	2
Typ av minnesplats:	DIMM
PCI Express x1 (Gen 3.x)-platser:	2
Gränssnitt för lagringsenheter som stöds:	M.2, SATA
PS/2-port(ar):	1
LAN-kontroller:	Realtek RTL8111H
Kompatibla processorer:	AMD Ryzen 3 3rd Gen, AMD Ryzen 5 3rd Gen, AMD Ryzen 7 3rd Gen, AMD Ryzen 9 3rd Gen
Minnestyper som stöds:	DDR4-SDRAM
Wifi:	Nee
Harmoniserad systemkod (HS):	84733020
Moderkort chipset familj:	AMD
Moderkorts formfaktor:	micro ATX
Antal minnesplatser:	4
Minnesklockhastigheter som stöds:	2133,2400,2666,2800,3000,3200,3333,3466,3600,3733,3866,4000,4133,4266,4400,4600 MHz
BIOS-typ:	UEFI AMI
BIOS-minnesstorlek:	256 Mbit
ATX-strömkontakt (24-stift):	Ja
USB 2.0-anslutningar:	2
USB 3.2 Gen 1 (3.1 Gen 1) anslutningar:	1
Antal M.2 (M) platser:	2
PCI Express x16 (Gen 4.x)-platser:	1