Perlick 3076 Bruksanvisning
Läs gratis den bruksanvisning för Perlick 3076 (6 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6.5 recensioner. Har du en fråga om Perlick 3076 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
Installation Instructions
Air-Cooled Wall Mount Beverage Dispenser
Form No. Z2507
Rev. 11.30.2022
Air Cooled Wall Mount Dispenser Installation Instructions
2
Installation of Air cooled Wall Mount Dispenser
1. Remove screws which
secure the back plate
to the dispenser.
3. Remove screws which
secure the bottom plate to
the dispenser.
Remove bottom plate and
set aside.
Parts Bag Included with Tower:
2. Remove back
plate and set aside.
Preparing for Installation:
Black Poly-tape Clear poly-tape
Elbow drain
tting with
barbed tailpiece
Straight drain
tting with
barbed tailpiece Spanner wrench
Parts bag contents include –
Included with Tower:
Wall Mount Dispenser
(Faucets and tap handles
shown are not included)
Mounting Bracket
Other Parts Needed for Installation: The parts required will vary depending on the installation.
PART NO. DESCRIPTION
C26609 Wall Mounted Air Shaft Connector, Cooler (1 required)
1655R Blower Kit, 134 CFM
C15365-1 3” Hose duct, blower to air shaft inside cooler - 12.5 feet
C15365-2 3” Hose duct, blower to air shaft inside cooler - 25 feet
C15366-1 Coupling Sleeve for 3” air shaft tube (1 required when joining two 12” sections)
C31573 Poly housing hanger strap kit
61082-1 Aluminum housing hanger
1390D 1/2” I.D. Vinyl Drain Tube – Anti-Microbial
Air Cooled Wall Mount Dispenser Installation Instructions
Form No. Z2507
Rev. 11.30.2022
3. Determine mounting location for dispensing
unit on wall.
Secure bracket to the wall.
Note: Align screws with as many wall studs
as possible to provide adequate support for
the dispenser.
After installing one screw, check to insure the
bracket is perfectly level before installing
remaining screws.
Note: Use mounting screws and anchors if
needed which are appropriate for the wall the
dispenser is to be installed on.
4. Hang back plate on the installed hanging track
making sure the plate is centered on the track.
Trace holes onto wall.
Remove back plate and set aside.
5. Measure to locate the exact center of each hole
location.
Mark centers.
6. Cut holes for air tube and beverage leads with
a 3-1/2” to 4” hole saw. The hole is larger than the
diameter of the air inlets on the dispensing units
to provide clearance when lowering the dispenser
into position.
Produktspecifikationer
| Varumärke: | Perlick |
| Kategori: | Inte kategoriserad |
| Modell: | 3076 |
Behöver du hjälp?
Om du behöver hjälp med Perlick 3076 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Perlick Manualer
10 December 2024
10 December 2024
10 December 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
Inte kategoriserad Manualer
- Brydge
- FontaFit
- JAR Systems
- Gardenline
- Hover-1
- Lindam
- Skullcandy
- FBT
- Asetek
- Envitec
- Hama
- Vakoss
- Bintec-elmeg
- Dux
- Porter-Cable
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025