Philips SQM7842 Bruksanvisning

Philips Inte kategoriserad SQM7842

Läs gratis den bruksanvisning för Philips SQM7842 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 1.5 recensioner. Har du en fråga om Philips SQM7842 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Engli s h

1 Important safety instructions

Caution

• Read these instructions before you begin. If you are unsure of any

part of the process, contact a professional contractor or installer

for assistance. Improper installation can result in injury or damage.

• The wall or mounting surface must be capable of supporting

the combined weight of the mount and the display; if not, the

structure must be reinforced.

• Locate pipes, wires, or any other hazards in the wall where you

wish to install the mount before drilling.

• Safety gear and proper tools must be used. Failure to do so can

result in injury or damage.

• Two people are recommended for installation. Do not attempt to

lift a heavy display without assistance.

• Follow all instructions and recommendations regarding adequate

ventilation and suitable locations for mounting your display.

Consult the owner‘s manual for your particular display for more

information.

• This wall mount is intended for use only with the maximum

weight of 45 kg (100 lbs). Use with heavier than the maximum

weights indicated may result in instability causing possible injury.

2 Tilt wall mount (for LCD, Plasma, and LED displays)

What's in the box

Wall plate (x1)

Mount arm (x2)

User manual (x1)

Hardware kit (x1)

Hardward kit

M8 x 63 lag bolt (x4)

Lag bolt washer (x4)

Concrete anchor (x4)

M6 x 12 screw (x4)

M6 x 30 screw (x4)

M8 x 12 screw (x4)

M8 x 30 screw (x4)

M6 washer (x4)

M8 washer (x4)

Spacer (x8)

Tools required

• Phillips head screw driver

• Ratchet or driver with 13 mm (1/2”) socket

• Electric or portable drill

• 6 mm (1/4”) drill bit and stud nder for drywall installation

• 10 mm (3/8”) Masonry bit for concrete installation

3 Installation

Mount to the drywall

Caution

For safety reasons, this mount must be secured to at least two

wood studs no less than 16” apart. The studs must be capable of

supporting the combined weight of the mount and display.

1 Use a high quality stud nder to locate two adjacent

studs where you wish to install your mount. Mark both

edges of each stud to help identify the exact center.

Note

You must use the center of each stud to avoid cracking or splitting

the wood during installation.

2 Place the wall plate against the wall and level it using the

integrated bubble level.

3 While another person holds the wall plate in position,

mark four locations (two per stud) for securing the

mount to the wall (see Fig. 1).

4 Set the wall plate aside and drill a 6 mm (1/4”) pilot hole

at each marked location.

5 Place the wall plate back against the wall and attach it

using the lag bolts

and lag bolt washers

provided

(see Fig. 2). Do not over-tighten these bolts and do not

release the wall plate until all bolts are in place. Ensure

that the wall plate remains level after all bolts are secured.

Mount to the concrete wall

Caution

For safety reasons, the concrete wall must be capable of

supporting the combined weight of the mount and the display. The

manufacturer takes no responsibility for failure caused by walls of

insufcient strength.

1 Place the wall plate against the wall in the desired

location and level it using the integrated bubble level.

2 While another person holds the wall plate in place, mark

four evenly spaced locations on the wall for securing the

mount (see Fig. 3).

3 Set the wall plate aside and drill a 10 mm (3/8”) hole at

each marked location. Remove any excess dust from the

holes.

4 Insert a concrete anchor

into each hole so that it is

ush with the concrete surface (see Fig. 4). A hammer can

be used to lightly tap the anchors into place if necessary.

1 2

8 9

2015 © Gibson Innovations Limited.

This product has been manufactured by, and is sold

under the responsibility of Gibson Innovations Ltd., and

Gibson Innovations Ltd. is the warrantor in relation to

this product.

Philips and the Philips Shield Emblem are registered

trademarks of Koninklijke Philips N.V. and are used

under license from Koninklijke Philips N.V.

UM_SQM7842

27_EN_V1.0

WK15314

SQM7842

www.philips.com/support

User manual

Manual del usuario

sqm7842_27_2L_um_150730.indd 1-3 30/07/2015 18:00:58

Produktspecifikationer

Varumärke:	Philips
Kategori:	Inte kategoriserad
Modell:	SQM7842
Färg på produkten:	Aluminium
Förpackningens bredd:	1350 mm
Djuppackning:	170 mm
Förpackningshöjd:	863 mm
Användarmanual:	Ja
Typ av förpackning:	Doos
Skärm diagonal:	55 "
Upplösning:	3840 x 2160 Pixels
Original bildförhållande:	16:9
Ethernet LAN:	Ja
Medföljande kablar:	AC
Skärmform:	Flat
Ljusstyrka:	- cd/m²
Snabbstartsguide:	Ja
Garantikort:	Ja
Antal USB 2.0-portar:	1
Antal HDMI-portar:	2
DVI-port:	Nee
Antal Ethernet LAN (RJ-45)-portar:	1
Smart TV:	Ja
Inbyggda högtalare:	Ja
Genomsnittlig effekt:	16 W
Strömförbrukning (i standby):	0.5 W
Antal batterier/batterier som stöds:	4
Analog signalformat:	NTSC, PAL
HDR-stöd:	Nee
HD typ:	4K Ultra HD
3D:	Nee
Displayteknik:	LED
Respons tid:	- ms
VESA montering:	Ja
Panelmonteringsgränssnitt:	200 x 200 mm
Djup (utan bas):	62.5 mm
Höjd (utan bas):	719.44 mm
Bredd (utan bas):	1231.6 mm
Vikt (utan bas):	13850 g
Common Interface Plus (CI+):	Nee
Typ av tuner:	Analoog & digitaal
Digitalt signalformat:	DTMB
Internet-TV:	Ja
Enhetsbredd (med stativ):	1231.6 mm
Djupenhet (med stativ):	250.48 mm
Enhetshöjd (med stativ):	753.62 mm
Vikt (med stativ):	14070 g
Skrivbordsställ:	Ja
Möjlighet att justera skärmmått:	4:3, 16:9
Text-TV:	Ja
Elektronisk TV-guide:	Ja
Gemensamt gränssnitt (CI):	Nee
Antal RF-portar:	1
Programmeringsperiod:	8 dag(en)
Firmware-uppgradering möjlig:	Ja
Firmware kan uppgraderas via:	Auto upgrade wizard, Network, USB
RF-anslutningstyp:	IEC
Digitalt ljud, koaxialutgång:	1
Fjärrkontroll ingår:	Ja
Wifi:	Ja
AC-ingångsspänning:	176 - 264 V
AC-ingångsfrekvens:	50 Hz
Strömförbrukning (typiskt):	150 W
Drifttemperatur (TT):	5 - 45 °C
Batterier-ingår:	Ja
Batterityp:	AAA