Pulsar AWO452 Bruksanvisning


Läs gratis den bruksanvisning för Pulsar AWO452 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 6 recensioner. Har du en fråga om Pulsar AWO452 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
INSTRUKCJA MONTAŻU/ASSEMBLY
POLSKI/ENGLISH
Kod / Code: AWO 452
EXPANDER 1 Nazwa / Name:
Obudowa metalowa do: ekspanderów, modułów GSM/ISDN itp.
Metal casings for: expanders, GSM/ISDN module, etc.
IM452
Wydanie: 2 z dnia 20.11.2017
Zastępuje wydanie: 1 z dnia 12.01.2012
PL
1. Przeznaczenie:
Obudow zaprojektowana a jako element tp. a AWO452 został systemów SSWiN, KD, i
Przeznaczona jest : do montażu (w zależności od modelu)
ekspanderów (modułów) wejść/wyjść itp.
nadajnik GSM a, modułu
innych dedyko wanych urządzeń
2. Montaż:
Obudowa instalatora, odpowiednie przeznaczona jest do montażu przez wykwalifikowanego posiadającego
( wymagane i konieczne dla danego kraju) zezwolenia i uprawnienia do ingerencji w instalacje niskonapięciowe.
Obudowa (+PCB) powinna być montowana w pomieszczeniach zamkniętych, o normalnej wilgotności powietrza
(RH=90% maks. bez kondensacji) i temperaturze z zakresu - 010°C do +4 °C.
Urządzenia elektroniczne elementy elektroniczne wrażliwe na wyładowania zawiera
elektrostatycz ne. Przed montażem należy rozładować ładunki elektrostatyczne,
a w czasie montażu unikać dotykania elementów na płycie.
1. poprzez przepusty Zamontować obudowę w dedykowanym miejscu i doprowadzić przewody połączeniowe i sygnałowe
kablowe.
2 Z . amontować w obudowie urządzenie w odpowiednich otworach montażowych ( z użyciem: kołków dystansowych,
wkrętów montażowych itp.).
3 . Wykonać połączenia wymagane dla danego typu urządzenia/systemu.
Uwagi: zgodnie z wymaganiami i zaleceniami producenta.
4. uruchomienie, regulacje lub konfiguracje: producenta systemu. Wykonać zgodnie z procedurą
5. Po instalacji i . uruchomieniu systemu należy zamknąć obudowę
1. Destination: EN
The metal casings are designed as components in intruders alarms, access cont l systems, security AWO 452 ro
systems etc. There are intended for installation:
expander modules
GSM transmiter, ISDN module
other to dedicated devices, components etc.
2. Installation:
The metal casing must be installed by a qualified installer, holding the relevant certificates, required and
necessary in the particular country for connecting (interfering with) -voltage installations. low
The casing should be installed indoors, where air humidity is normal (RH=90% max. without condensation) and
temperature in the range of - 0 10°C do +4 °C.
Caution! Electronic devices contains electronic components sensitive to
electric charges. Prior to installation, these charges must be removed. During
installation, avoid touching any elements on the board.
1. Install metal casing in dedicated place and bring in the connecting and signal conductors through cables bushings.
2. Mount the device with dedicated holes (use: distance pins, bracket screw).
3. Make other connections required for the correct type of system / device.
Remarks: consistent with requirements and recommendation of the producer.
4. Start the system, adjust or configure: according to procedure of system. the producer’s
5 After installing and checking the proper operation of the system, close the casing. .


Produktspecifikationer

Varumärke: Pulsar
Kategori: Inte kategoriserad
Modell: AWO452

Behöver du hjälp?

Om du behöver hjälp med Pulsar AWO452 ställ en fråga nedan och andra användare kommer att svara dig