Pyle Pro PIC6E Bruksanvisning

Pyle Pro högtalare PIC6E

Läs gratis den bruksanvisning för Pyle Pro PIC6E (1 sidor) i kategorin högtalare. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 6 recensioner. Har du en fråga om Pyle Pro PIC6E eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/1

1.Introduction

The Pyle Home PIC6E/PIC8E both feature adjustable silk dome

tweeters and adjustable treble contro, allowing you

to select + 3dB, 0dB, -3dB adjustments. These

speakers are optimized for the demands of home

theater applications, and incorporate a 2 Way

speaker design, with a Poly Cone woofer made from

UFLC (Urethane Film Laminated Cloth). This set

includes paint rings and installation hardware, and

pre-construction installation, and pre-construction

installation brackets are also available seperately.

Disclaimer: Make sure you are in compliance with local building codes before

installing this speaker, These Pyle Home In-Ceiling Speakers are suitable for

moisture rich environments such as bathrooms or saunas, but not outdoor

applications.

INSTRUCTION &

INSTALLATION SHEET

PIC6E/PIC8E

In-Ceiling Speaker

INSTRUCTION &

INSTALLATION SHEET

PIC6E/PIC8E

In-Ceiling Speaker

2.Description

The PIC6E/PIC8E are made from a durable, semi-flexible plastic material that feature

built in foam gaskets to minimize vibration and maximize the installation seal. They

also feature a perforated metal grill with an acoustically transparent scrim cloth to

enhance the speakers appearance once installed. Pyle Home In-Ceiling speakers are

paintable, and well suited for moisture rich environments. They also feature flip out

tabs for easy installation and removal.

3.Installation

Installation of this PIC6E/PIC8E In-Ceiling speakers can be easily accomplished at multiple

stages of the construction process, whether it be “Rough In” (before drywall) or “Trim-Out”

(after drywall is Installed and painted)

A. “Rough-in” steps:

NOTE: It is recommended that a minimum of 16 gauge, 4

conductor wire be used for most applications from the amplifier or

volume control to this speaker. Different gauges can, and should,

be used based upon the distance of the intended run or quality of

installation(see Figure2).

www.pyleaudio.com

Speaker Wire

Gauge Selection Chart

Distance

<10 Feet

10-50 Fe et

>50 Feet

Gau ge

Figure 2

Figure 1

(shown with grill removed)

1.Run x/4 conductor (x=gauge preference) stranded speaker wire

from the distribution/volume control to the speaker location (pre-

wiring).

2.If PYLEAUDIO Speaker Pre-Construction Bracket is to be used,

skip to Step “5”.

3.If pre-wiring without using the PYLEAUDIO Pre-Construction

Speaker Brackets, leave 4 to 6 feet of wire at the speaker's

intended location. Use a strip of cardboard stapled to the

joints/studs with a hole through it as a wire place holder for the

drywall installers if installation of the speakers is intended ( see

Figure 3).

4.After drywall and/or painting is complete, push wire though hole,

center template over hole, mark with a pencil and cut out with a

drywall knife.

5 When using the PYLEAUDIO Pre-Construction Bracket (see .

figure 4), leave a coil of speaker wire on top of the bracket coiled

around the speaker mounting hole. There are clips on the corner of

the bracket to secure the speaker wire. Leave enough speaker wire

to be able to pull the wire through the speaker after the drywall is

installed. Strip off 3 inches or so of the speaker cable jacket to

expose the positive and negative insulate wires. Strip 3/8-1/2 inch

of insulation off of these conductors.

6 It is recommended to place insulation behind the speaker to .

provide some damping for the woofer driver. This will yield the best

po s s i b l e s o u nd . P Y LE AU DI O r e c o m m e n ds u s i ng p o l y -

encapsulated insulation such as Johns Manville Comfort Therm. If

a defined, consistent sound is desired to yield the ideal cubic

footage for the driver. Insulation would then be put in this space

during speaker installation .Refer to blocking chart for details.

7 If installing the speaker in a space with an attic above it is .

recommended that the speaker be boxed in with 1/2 inch MDF

(medium density fiber board) or plywood with insulation installed.

This will provide a defined acoustic space and protect the speaker.

The best possible sound will be achieved by doing this. Refer to

the blocking chart for details.

www.pyleaudio.com

NOTE: Make sure you are in compliance with local building codes before installing this

speaker in an attic space.

Figure 4

Figure 3

Plea se P ul l Thr u Dr y- Wall He re

Ins ul ati on

Bat ting

2 x 10 Joists

16” on Center

Blo ck ing

Dis ta nce

B. “Trim-out steps:

1 After drywall and/or painting is complete, push the speaker wire .

through hole, center template over hole, mark with a pencil and cut

out with a dry-wall knife.

2 Hold the speaker with one hand,(if speaker grill is off, pay careful .

attention to push on the woofer's cone, this can cause not

permanent distortion of the voice coil, thus producing a mechanical

rubbing sound or speaker failure),push in the speaker terminal

connectors and insert wires; remove speaker grill. Be sure to have

the positive wires in the RED terminals and the negative wires in

the BLACK terminals.

NOTE: Wiring both drivers of this speaker identically as the

above instruction states will yield a speaker whose drivers are

“in phase”. If one speaker driver is wired opposite of the other,

the speaker drivers will be “out of phase” with one another. If

the speaker drivers are “out of phase” the sound might appear

smeared (canned) and a significant loss of bass might be

noticeable due to phase cancellation. Make sure every

installed speaker is correctly phased.

3 Rotate the speaker driver towards the listening area and use one .

hand to push the speaker into the cut out (again, pay careful

attention to push on the woofer's cone this can cause not

permanent distortion of the voice coil, thus producing mechanical

rubbing sound or speaker failure) and the other to turn the screws

that engage the installation tabs (see ). Tighten the tabs in Figure5

a cross or X-pattern until “snug”. Be careful not to over tighten the

tabs or damage could result. The speaker should appear flush to

the surface.

NOTE: If using a cordless drill/screwdriver, it is suggested that

the screws be turned until almost tight, then finish tightening

via a hand screwdriver.

www.pyleaudio.com

NOTE:A strip of grill adhesive is provided to more securely attach the speaker grills on

final installation. Simply insert several short strips evenly around the grill slot prior to

installing the grill cover. Prior to final installation of the grill, adjust the tweeter for

optimum sound at the listening area.

6.5” Speak er (0.7 CuFt) Blocking Distance

16” on Center, 2x4

16” on Center, 2x6

16” on Center, 2x8

16” on Center, 2x10

16” on Center, 2x12

24” on Center, 2x4

24” on Center, 2x6

24.00”

15.25”

11.50”

9.00”

7.50”

15.50”

10.00”

8” Speak er (2.1 CuFt) Blocking Distanc e

16” on Center, 2x4

16” on Center, 2x6

16” on Center, 2x8

16” on Center, 2x10

16” on Center, 2x12

24” on Center, 2x4

24” on Center, 2x6

71.5”

45.50”

34.50”

27.00”

22.25”

46.00”

29.50”

PYLEAUDIO Speaker Blocking

Chart

Speaker

Specifications

Figure 5

Size/Type

Efficiency

Power(RMS/Peak)

Frequency Response

Woofer Type

Tweeter Type

Impedance

6.5” In-Ceiling 8” In-Ceiling

88dB 88dB

125W/250W 150W/300W

45-20KHz 35-20K

Polypropylene Polypropylene

UFLC Adjustable UFLC Adjustable

4-8 Ohm 4-8 Ohm

PIC6E PIC8E

INSTRUCTION &

INSTALLATION SHEET

PIC6E/PIC8E

In-Ceiling Speaker

3260100333,PIC6E/PIC8E通用说明书：A3纸，

105G铜版纸单色印刷说明书,A版

Produktspecifikationer

Varumärke:	Pyle Pro
Kategori:	högtalare
Modell:	PIC6E
Färg på produkten:	Silver, White
Förpackningens bredd:	144 mm
Djuppackning:	101 mm
Förpackningshöjd:	58 mm
Typ lampa:	LED
Strömlampa:	3 W
Typ av förpackning:	Geschenkdoos
Medföljande kablar:	DC
Material:	Kunststof
Antal per paket:	2 stuk(s)
Lichtstroom:	150 lm
Lampans livslängd:	25000 uur
Färg ljus:	Warm wit
Färgtemperatur:	2700 K
Färgåtergivningsindex (CRI):	80
Strålvinkel:	120 °
Antal lysdioder:	25
Spänningslampa:	12 V
Energieffektivitetsklass ingår lampa (gammal):	A