Pyle PSPTR19 Bruksanvisning

Pyle Sportklocka PSPTR19

Läs gratis den bruksanvisning för Pyle PSPTR19 (2 sidor) i kategorin Sportklocka. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 5 recensioner. Har du en fråga om Pyle PSPTR19 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

ACTIVITY MODE

Hold the ACT/EL button for 2 seconds to enter the activity mode.

PERSONAL TRAINER

Thank you for choosing X-Tracker as your personal trainer. We want you to

make the most out of your new gadget, so please read the instruction manual

carefully, and keep the manual for future reference.

Important:

Please note that the watch is NOT a medical device and is not to be used as such.

The X-Tracker requires one CR2032 lithium battery. Only the recommended

batteries are to be used.

When replacing the batteries, the following are to be strictly observed.

1. Only the recommended batteries are to be used.

2. Only adults should install and replace the batteries.

3. DO NOT use rechargeable batteries, and DO NOT recharge non-

rechargeable batteries.

INSTALLING THE BATTERY

1. The battery compartments are located at the back of the watch.

2. To install or replace the battery, unscrew the back cover carefully.

3. Take out the old batteries and dispose responsibly.

4. Gently place a new battery into the battery slot of the battery compartment,

making sure that the poles are correctly placed, and screw the back cover on.

3D SENSOR - MEASURES YOUR MOVEMENT ACCURATELY

The 3D technology uses an accelerometer sensor that detects and measures

only count steps after an initial detection of continuous steps.

CONT NTS

Getting Start ………………………………………………………………………

Important Battery Information …………………………………………………..

Installing the Battery…………………………………………….………….……

Using the watch function…………………………………………………...……

Symbol on LCD……………………………………………………………...……

Mode Flow Chart…………………………………………………………….……

Time Mode ………………………………………………………………….……

Setting Time ….……………………………….………………………........……

Alarm Mode………………………………………………………………….……

Setting Alarm …….………………………………………………………….……

Stopwatch Mode …………………………………………………………....……

Step Counting Mode ………………………………………………………..……

Sleeping Mode …..…………………………………………………….......……

Indication of the sleeping quality………………….…………………….....……

Memory Mode…………………………………………………..…………...……

User Setting Mode……………………………………………………….….……

Activity Mode.………………………………………………………………..……

Caution……………………………………………………………………….……

2 3 4

65 7 8

SCREW

BACKCOVER

ORing

CR2032

BATTERY

Multi-Function Wrist Watch

Press all 4 buttons at the same time to reset the watch.

SETTING TIME

1. Hold the MODE button for 3 seconds to enter setting mode.

2. Press ST/SP/+ button to toggle 12Hr or 24Hr.

3. Press MODE button to set seconds.

ALARM MODE

1. Press the MODE button to scroll through the menu until you locate the

alarm mode, “ ALARM ”.

2. Press ST/SP/+ button to activate or deactivate the alarm.

3. Press RE/ - button to activate or deactivate the hourly chime.

MODE FLOW CHART

Press MODE button to scroll through the dierent modes.

TIME MODE – ALARM MODE – STOPWATCH MODE – STEP COUNTING

MODE – SLEEPING MODE – MEMORY MODE – USER SETTING MODE

TIME MODE

1. Press the MODE button to scroll through the menu until you locate the time

mode, “ TIME ”.

2. Press ST/SP/+ button to view the Date.

3. Press RE/- button to toggle the Day and Seconds.

1 2 3

SETTING ALARM

1. Hold the MODE button for 3 seconds to set the alarm, and the minutes’

2. Press or hold either the ST/SP/+ button to increment the minutes’ digit

or RE/ - button to decrement the value.

and the hours’

4. Press or hold either the ST/SP/+ button to increment.

the hours’ digit or RE/ - button to decrement the value.

5. To save and exit setting mode, hold the

MODE button for 3 seconds or alternatively,

one minute of inactivity will trigger the watch

to return to the default TIME mode.

Notes

- Any changes made in the alarm mode will automatically enable the alarm.

- If the watch is inactive for longer than 1 minute in any modes, the main

screen will automatically return to time mode.

STOPWATCH MODE

1. Press the MODE button to scroll through the menu until you locate the

stopwatch mode, “ STW ”.

2. Press ST/SP/+ button to start the stopwatch, and press again to stop the

stopwatch.

3. Hold the RE/ - button for 3 seconds to reset the stopwatch to zero.

USING THE WATCH

I PORTA T!

f for energy

saving purposes, and you can turn it on by pressing the MODE key.

 automatically at

midnight (00.00/12.00am). Press the MODE key to turn it on.

The watch comes with 2 major activity function:- PEDOMETER & SLEEPING

MONITOR. Only one function can be used at any one time. Normally, the

watch will operate under the pedometer mode, unless the sleeping monitor

has been activated. It will go back to pedometer function once the sleeping

monitor mode has been deactivated (Saved/Deleted).

There maybe a delay between the start of your walk and the counting of

steps. y, and exclude

movements outside of a normal walking motion. Once the watch has

recognized your walking activity, it will take into account the initial steps

taken during the delay.

screen will automatically return to time mode.

please wear the watch properly as shown in the diagram (strap of the watch

must fasten tightly around the wrist and it must not be loose; display must

also be perpendicular to the forearm and wrist; the watch must only be

worn on the left wrist and not the right to maximize the accuracy of step

counting) as the design and accuracy of the watch for step counting is

based on the positioning of the watch. By wearing the watch correctly, the

steps counted during the walk will be more accurate.

SHAKE IT TO WAKE IT!

Shake the watch to turn on the EL backlight. At default, this function will turn

ON automatically at 18:00 and o at 08:00, and you can hold the ST/SP/+

button for 2 seconds during Time Mode to activate or deactivate this function.

REMINDER

GETTING STARTED

Prior to your purchase of the watch, the watch is switched o for energy saving

purposes, and you can turn it on by pressing the MODE key.

For energy saving purposes, the watch unit will switch o automatically at

midnight. Press the MODE key to turn it on.

PEDOMETER & SLEEPING MONITOR

The watch comes with 2 major activity function:- PEDOMETER & SLEEPING

MONITOR. Only one function can be used at any one time. Normally, the

watch will operate under the pedometer mode unless the sleeping monitor

has been activated. It will return to pedometer function once the sleeping

monitor mode has been stopped.

There maybe a delay between the start of your walk and the counting of

steps. y, and exclude

movements outside of a normal walking motion. Once the watch has

recognized your walking activity, it will take into account the initial steps

taken during the delay.

NOTE

If the watch is inactive for longer than 1 minute in any modes, the main screen

will automatically return to time mode.

personal data in user settings mode.

- All functions with the exception of time mode, will be inactive, the sleeping

monitor data must be (saved/deleted), to resume access to all functions.

detection of continuous steps.

- Whilst the sleeping mode is on, all modes cannot be accessed with the

exception of time mode & alarm mode, or until the sleeping record has been

completed (saved/deleted).

SHAKE IT TO WAKE IT!

Shake the watch to turn on the EL backlight. At default, this function will turn

ON automatically at 18:00 and o at 08:00, hold the ST/SP/+ button for 3

seconds during Time Mode to activate or deactivate this function. Frequent

usage of the ‘SHAKE IT TO WAKE’ function, will shorten the battery life of

the product. We recommend all users to turn o this function whilst undergoing

exercise.

4. Press ST/SP/+ button to reset zero.

5. Press MODE button to set minutes.

6. Press or hold either the ST/SP/+ button to increment the minutes’ digits or