QSC AD-S402T Bruksanvisning

QSC högtalare AD-S402T

Läs gratis den bruksanvisning för QSC AD-S402T (4 sidor) i kategorin högtalare. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 4 recensioner. Har du en fråga om QSC AD-S402T eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/4

1TD-001597-01-A

AD-S402T

Quick Start Guide

NOTE:

The AD-S402T is UL listed (1480A) for indoor use only

Installation

AD-S402T passive column loudspeaker systems require ampliﬁed audio signals. A pass-through on each loudspeaker permits connection to multiple loudspeakers.

The pluggable “Eurostyle” connectors allow the installer to pre-wire the audio system on site before the loudspeakers are installed.

TD-001597-01-A

*TD-001597-01*

The loudspeaker comes with a weather cover for the input cup to protect the input connections and switches from

precipitation and other weather hazards (Figure 1). Use the weather cover for all non-UL outdoor installations or any

applications where the loudspeaker may be exposed to moisture. To ensure a good seal in the cable gland, use outdoor-rated

cable with a round jacket between 5.5 mm and 9.4 mm in diameter.

To use the weather cover:

1. Loosen the nut on the cable gland.

2. Pass the cable all the way through the nut and the rest of the gland.

3. Attach the input connector to the wires (see

Input Connector

, below).

4. Once the loudspeaker enclosure is installed, plug the input connector into the loudspeaker's input cup. Secure the

connector to the loudspeaker using the two captive retaining screws, one on each end.

5. Make sure that the transformer tap selection switch is set properly.

6. Place the cover onto the loudspeaker's input cup and attach it using the four screws, lock washers, and ﬂat washers

provided.

7. Dress the cable so there is no undue strain on it. Tighten the gland nut until the grommet inside the gland has made a

tight seal onto the cable jacket.

Input Connector

AD-S402T Weather Cover

Diameter

up to

0.37 in

9.4 mm

— Figure 1 –

Strip wire

¼ in

6.3 mm

Up to

10 GAW

6 mm²



Turn screw fully

counterclockwise.



Insert wire fully.



Turn screw clockwise

to clamp wire tightly.

— Figure 2 –

INPUT

THRU To other

loudspeaker(s),

if necessary

— Figure 3 –

The pluggable “Eurostyle” input connector (Figure 2) has four terminals to facilitate connection on a distributed

line. It also allows the installer to pre-wire the venue before the loudspeakers themselves are installed. The

connector accommodates wire up to 10 AWG or 6 mm2. Be sure of proper and consistent polarity at each connector

(Figure 3). If one or more loudspeakers is out of polarity with others, the acoustic performance will suffer. Always

secure the connector to the loudspeaker using the retaining screws at both ends.

Mounting

Tilt/Swivel Bracket

The bracket provided with the loudspeaker allows 0, 5,

10, 15, and 20 degrees of downward tilt (Figure 4), and

up to ±55 degrees of horizontal panning (Figure 5).

These angles may be constrained by the loudspeaker

enclosure and adjacent walls or other structural elements.

In addition, the bracket can be inverted, which allows the

loudspeaker to be tilted up.

— Figure 4 –

— Figure 5 –

Produktspecifikationer

Varumärke:	QSC
Kategori:	högtalare
Modell:	AD-S402T
Typ av operation:	Touch
Färg på produkten:	Wit
Förpackningens bredd:	260 mm
Djuppackning:	320 mm
Förpackningshöjd:	25 mm
Snäll:	Elektronische weegschaal
Automatisk avstängning:	Ja
Beeldscherm:	LCD
Typ av strömkälla:	Batterij/Accu
Noggrannhet:	100 g
Maximal viktkapacitet:	150 kg
Form:	Rechthoek
Material:	Glas
Indikation på lågt batteri:	Ja
Antal per paket:	1 stuk(s)
Överbelastningsindikator:	Ja