Radial Engineering DiNET DAN-TX Bruksanvisning
Radial Engineering
Inte kategoriserad
DiNET DAN-TX
Läs gratis den bruksanvisning för Radial Engineering DiNET DAN-TX (9 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 5 recensioner. Har du en fråga om Radial Engineering DiNET DAN-TX eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
www.radialeng.com
True to the Music™
®
User Guide
DAN-TX™
2-Chan Dante® Transmitter
Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam
British Columbia, Canada, V3C 5M5
Tel: 604-942-1001 • Fax: 604-942-1010
Email: info@radialeng.com
Note: This device has been tested and found to comply with the limits
for a Class A digital device, according to Part 15 of the FCC Rules and
EN55022. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a commercial environ-
ment. This device generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the user manual, may cause harmful
interference to radio communications. Operation of this device in a residential area
is likely to cause harmful interference, in which case the user will be required to
correct the interference at their own expense.
Radial Engineering Ltd. DiNET DAN-TX™
True to the Music
®
1
OVERVIEW
The DiNET DAN-TX is an analog to digital converter that is designed to
take the signal from instruments or line level audio sources and transmit
them over an existing Dante-enabled network.
A typical direct box is a device that converts an unbalanced high-
impedance instrument or consumer line level audio output to a balanced
low-impedance signal that can easily interface with a professional audio
system. The Radial DiNet DAN-TX provides the same input options of a
multi-media direct box, but converts the audio to a digital stream that is
suitable for direct connection to a Dante network over Ethernet.
The DAN-TX is equipped with a variety of connection options to make
it easy to connect with any type of audio equipment. The included
stereo 3.5mm, RCA and ¼” connectors are wired in parallel to allow
for immediate hookup of instruments, tablets, smartphones, consumer
audio devices, broadcast and professional audio equipment without the
need for adapter cables. When additional signal handling is required, the
switching ¼” jacks adapt to both unbalanced (TS) and balanced (TRS)
connectors to accommodate +4dBu sources, with a maximum input of
up to +28dBu.
The inputs of the DAN-TX are processed using high quality 24 bit/ 96kHz
analog-to-digital converters, providing two channels of Dante digital
outputs over a single Ethernet connector, and allowing easy integration
of analog audio devices with an existing Dante network.
Computer running
Dante Controller
for setup
Dante Network
Produktspecifikationer
| Varumärke: | Radial Engineering |
| Kategori: | Inte kategoriserad |
| Modell: | DiNET DAN-TX |
Behöver du hjälp?
Om du behöver hjälp med Radial Engineering DiNET DAN-TX ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Radial Engineering Manualer
2 April 2025
25 Februari 2025
25 Februari 2025
11 Februari 2025
11 Februari 2025
11 Februari 2025
11 Februari 2025
11 Februari 2025
11 Februari 2025
11 Februari 2025
Inte kategoriserad Manualer
- DoughXpress
- ZeeVee
- Playtive
- Rosieres
- Alto
- Arlec
- Uvex
- Innovative
- Balay
- Petzl
- Sabrent
- Vivitar
- Sikkens
- Bauknecht
- Ufesa
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025