Randell BC-003UC Bruksanvisning
Läs gratis den bruksanvisning för Randell BC-003UC (16 sidor) i kategorin kylskåp. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 2 recensioner. Har du en fråga om Randell BC-003UC eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/16
OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR
PART NUMBER PP MNL2104, REV. B (02/24)
This manual provides information for:
BLAST CHILLERS
BC-918RI, BC-510WT, BC-003UC
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ,
UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED
IN THIS MANUAL.
FOR YOUR SAFETY Do not store or use gasoline or other ammable vapors
and liquids in the vicinity of this or any other appliance.
NOTIFY CARRIER OF DAMAGE AT ONCE It is the responsibility of the
consignee to inspect the container upon receipt of same and to determine
the possibility of any damage, including concealed damage. Randell suggests
that if you are suspicious of damage to make a notation on the delivery
receipt. It will be the responsibility of the consignee to le a claim with the
carrier. We recommend that you do so at once.
Manufacture Service/Questions 888-994-7636.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE: Due to a continuous program of product improvement, Randell reserves the
right to make changes in design and specications without prior notice.
NOTICE: Please read the entire manual carefully before installation. If certain
recommended procedures are not followed, warranty claims will be denied.
MODEL NUMBER _________________________
SERIAL NUMBER _________________________
INSTALLATION DATE ______________________
The serial number is located on the interior rear wall
of the Blast Chiller.
EQUIPMENT DESCRIPTION
888-994-7636, fax 888-864-7636
uniedbrands.net
Model No. Body Style Length Depth Height Pan Capacity
(12” x 20” x
2.5”)
Pan Capacity
(18” x 26”)
NEMA BTU
Requirements
for Remote
Installations
HP Approx.
Weight
BC-003UC Undercounter 27” 30” 35” 3 - 5-20P
5400 @ 20F
Evap Temp
1/2 320
BC-510WT Worktop 59" 34” 36” 10 5 5-20P
6050 @20F
Evap Temp
3/4 565
BC-918RI Upright 40” 38.7” 71" 18 9 L14-20P
12100 @ 20F
Evap Temp
1-1/2 858
BC-918RIBC-510WTBC-003UC
Information contained in this document is known to be current and accurate at the time of printing/creation. Reference our product line website for the most updated
product information and specications. © 2024 Electrolux Professional, Inc. All Rights Reserved.
2 OM-BLAST CHILLER
INSTALLATION
SELECTING A LOCATION FOR YOUR NEW UNIT
The following conditions should be considered when selecting a location for
your unit:
1. Floor Load: The area on which the unit will rest must be level, free of vibration,
and suitably strong enough to support the combined weights of the unit plus
the maximum product load weight. All casters or legs must be in contact with
the oor to support the weight. Legs have adjustable feet that can be raised
or lowered. Casters may require shims in order for the caster to be in contact
with the oor. NOTE: If there is a question pertaining to weight load limits,
consult the factory at 1-888-994-7636.
2. Ventilation: The air-cooled self-contained unit requires a sufcient amount
of cool clean air. Avoid surrounding your blast chiller around other heat
generating equipment and out of direct sunlight. Also, avoid locating in
an unheated room or where the room temperature may drop below 55° F
(13°C) or above 86°F (32°C).
3. Clearance: There must be a combined total of at least 3” clearance on all
sides of the unit.
INSTALLATION CHECKLIST
After the nal location has been determined, refer to the following checklist prior
to start-up:
1. Check all exposed refrigeration lines to ensure that they are not kinked,
dented, or rubbing together.
2. Check that the condenser and evaporator fans rotate freely without striking
any stationary members.
3. Turn on control once unit has been plugged in or properly wired direct (see
page 15)
4. Allow unit time to cool down to holding temperature. (See page 10 for Unit
Operation).
5. Refer to the front of this manual for serial number location. Please record
this information in your manual on page 3 now. It will be necessary when
ordering replacement parts or requesting warranty service.
6. Conrm that the unit is holding temperature.
7. Allow your unit to operate for approximately 30 minutes before putting in
food to allow interior of unit to cool down to storage temperature.
NOTE: All motors are oiled and sealed.
NOTE: FAILURE TO FOLLOW INSTALLATION GUIDELINES AND RECOMMENDATIONS
MAY VOID THE WARRANTY ON YOUR UNIT.
ELECTRICAL SUPPLY
The wiring should be done by a qualied electrician in accordance with local
electrical codes. A properly wired and grounded outlet will assure proper
operation. Please consult the data tag attached to the compressor to ascertain
the correct electrical requirements. Supply voltage and amperage requirements
are located on the serial number tag located on the rear interior wall.
NOTE: It is important that a voltage reading be made at the compressor
motor electrical connections, while the unit is in operation to verify the correct
voltage required by the compressor is being supplied. Low or high voltage can
detrimentally affect operation and thereby void its warranty.
NOTE: It is important that your unit has its own dedicated line. Condensing
units are designed to operate with a voltage uctuation of plus or minus 10% of
the voltage indicated on the unit data tag. Burn out of a condensing unit due to
exceeding voltage limits will void the warranty.
OPERATION
The Randell BC series blast chillers are designed for rapid chilling through the
danger zone down to 40°F or below in approximately 90 minutes. The exact chill
time will vary depending on product type. The door must be in closed position to
activate switch at top of door before any cooling cycle will begin.
INTRODUCTION
1. The control software for the BC Control Unit is based on a Real-Time Operating
System and is capable of simultaneously running a chiller operation while at
the same time accepting/displaying user information from the control panel
such as chiller preset adjustments. This document provides an overview of the
current controller features.
POWERING UP UNIT
1. Once the unit is connected to AC power the touch screen will display a loading
screen with a progress bar.
2. Once loaded the standby screen will be displayed. Depressing the power key
on initial power up will cause the unit to request setting of the date and time.
Adjust the date and time values by touching the desired value, press the set
button then use arrow buttons to adjust value up or down. After all values have
been set press the return button on the bottom right of the screen to return to
the standby screen.
SETTING THE DATE/TIME
1. Upon turning on the unit for the rst time, the controller will prompt the user to
set the current date and time of day.
2. To adjust the date or time after initial power up you must access the Date Set
function. This function can be accessed by entering the menu screen from the
home screen then the control panel.
Menu à Control Panel à Date Set
POWERING DOWN UNIT
The unit may be returned to the low power standby state by depressing the
power button. The display will then return to the standby screen. NOTE: Power
should only be removed from the unit while it is idle on this standby screen.
MODES OF OPERATION
The controller can run one of three possible modes, Auto, Manual, or Hold.
1. Auto Mode - Auto Mode will run a chill cycle until all food probes have reached
a preset set point.
a. Auto can be manually selected by pressing the “AUTO” button on the
home screen.
- The food probe set point can be modied by entering the setting menu
via the “SET” button at the bottom of the auto cycle screen.
b. Auto cycle will start automatically from home screen or while running a
hold cycle if food probes are placed directly into food product and probes
have exceeded 100°F
c. Once an auto cycle has completed the unit will perform a defrost cycle. The
word defrost will display on the cycle screen once the defrost cycle has
activated and will remain until the evaporator coil has properly defrosted.
d. After completion of the defrost cycle the unit will hold the cabinet at the
hold set point until the user removes the product and ends the chill cycle
by pressing the “X” in the lower right-hand corner of the cycle screen.
2. Manual Mode - Manual Mode will run a chill cycle for a user set duration that
is not controlled by food probe temperature. Chill cycle will only end when set
duration has expired or user intervention occurs.
3. Hold Mode - Cabinet temperature will be held at a user dened set point.
This can be used to pre chill the cabinet prior to an auto/manual chill cycle or
temporarily hold food product. Not intended for extended food product storage.
Produktspecifikationer
| Varumärke: | Randell |
| Kategori: | kylskåp |
| Modell: | BC-003UC |
Behöver du hjälp?
Om du behöver hjälp med Randell BC-003UC ställ en fråga nedan och andra användare kommer att svara dig
kylskåp Randell Manualer
4 September 2025
kylskåp Manualer
- Temptech
- Teka
- Zerowatt
- Sam Cook
- Blaze
- Schmick
- Campingaz
- Gram
- Ariston Thermo
- Adler
- Lamona
- Milectric
- Ariston
- Salora
- Schneider
Nyaste kylskåp Manualer
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025
5 September 2025