Reflecta Episcope A4 Bruksanvisning
Reflecta
ej kategoriserat
Episcope A4
Läs gratis den bruksanvisning för Reflecta Episcope A4 (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 2 recensioner. Har du en fråga om Reflecta Episcope A4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
GB
Operating instructions
Revision A
Publication ID: 041 136 517
All rights reserved
Index
Important safeguards 3 ................................
Legend ...................................................... 4
Packaging content ..................................... 4
Main parts of the projector ................................ 4
Preparing the projection ............................ 4
Use and operation of the projector 5 .............
Operating instructions 5 ...............................
Focusing ................................................... 5
Replacement of a burnt-out lamp 5 ..............
Protection from overheating 6 ......................
After cooling .............................................. 6
Replacement of a blown fuse .................... 6
Cleaning of projector ................................. 6
Technical data ...........................................6
Replacement of the auxiliary lamp
The auxiliary lamp should be replaced by a
specialist only.
Protection from overheating
When the equipment overheats the lamps turn o
automatically. Check if the air-intake opening
(13) and the a -outlet opening (14) are not ir
obstructed!
After the device has cooled down the lamps turn
on automatically.
After cooling
Following prolonged use the cooling system can
continue to operate after the projector has been
switched o. The thermostatic controlled fans will
stop to operate after some time.
Replacement of a blown fuse
When the device is connected to the mains and
switched on and neither the ventilator, nor any of
the lamps come on then the fuse has blown.
WARNING: Before the replacement of the fuse
you must disconnect the plug from the wall-
socket!
Turn the fuse holder for a quarter of a turn and
pull out the blown fuse together with its holder.
Replace the fuse with a new one of the same
rating (10A 250V slow).
Should it happen that the just replaced fuse
blows again after the device has been switched
on, take the projector to be serviced.
Cleaning of the projector
WARNING: Before cleaning disconnect the plug
from the wall-socket!
For cleaning use distillated water or a mild
detergent solution. Use a clean and soft cloth
that will not leave any scratches. Clean the
projection glass (16) and the objective lens (1) in
the same way.
Technical Data
Working area:
285×285 mm
3-lens-objective:
2.8 / f=330mm
Halogen reector lamps:
ENX 82V / 360W (4x)
Auxiliary lamp:
15W / 230V, socket E14, mat t
Ø
max
27 mm, L
max
58 mm,
(i.e.: Osram T26/57 FR15)
Enlargement:
3.5x to 9.5x
Projection distance:
1.5 m 3.5 m –
Size of projected image:
1.0 m 2.7 m –
Mains voltage:
dependant on the model
220V / 50-60 Hz
230V / 50-60 Hz (EU)
240V / 50-60 Hz (UK)
Power consumption:
1500W
Dimensions of the projector:
590×480×330 mm
Weight:
19.5 kg
1 2 3
44
4 5
6 13
14 14
7 8 9 10
11
12
6
15 15
16
6
Use and operation of the projector
The projector is a device used to show opaque
objects, separate pieces of paper as well as
books, maps and thick three-dimensional
objects.
We recommend reducing the light before
projection.
The projector can be used in dierent
ways:
Lifting the cover, the projection lamps go out
and the less bright auxiliary lamp lights up,
allowing the projecting area to remain visible
in the darkened room.
The cover of the projector can be also
removed. Consequently thick 3-D objects
put on the projection glass can be projected.
The cover of the projector can also be
removed when larger surfaces, such as
maps are projected.
Examples of projection:
From a piece of paper to a 3- -book: Picture A cm
Lift the cover of the projector and place the
object to be projected on the projection
glass. Close the cover and switch on the
projector if switched-o. Check the
sharpnes.
3-D object: Picture B
Switch o the projector. Remove the cover.
Place the object on the projection glass and
cover it with the blackout cloth/
dust cover provided. Operate the override
switch by means of a coin and switch on
the projector. Check the sharpne s.
To replace the object with another one
switch o the projector or rotate the override
switch.
Map or piece of paper of larger format:
Picture C
Procede as in the case of projecting a
3-D object. However we recommend to use
a special cover instead of the provided
cover. The special cover can be purchased
from your dealer.
Tip: if the described way of projection is not
used frequently, the original cover can be
turned upside down instead of having to use
the special cover.
Operation instructions
The projection glass heats up quite intensily
when in use! We recommend not to touch it
during the projection phase.
The projected objects are heated to the same
extent. Consequently we recommend not to
touch project objects sensitive to
temperatures in excess of 80
0
C.
Paper objects can buckle during a longer
projecting time as a consequence of the loss
of moisture.
Focusing
Adjust the picture at the bottom edge by
means of the focus knob (2). Then turn the
Tilt and sharpness correction knob (10) to
sharpen the picture at the top edge. At the
end operate the focus knob (2) again to
correct the sharpness of the picture as a
whole.
Replacement of a burnt-out lamp
WARNING: The interior of the projector is
very hot! Before the replacement of a lamp
the projector must be left to cool down!
Check on the control panel which lamp has
burnt out. Switch o the projector and unplug
it from the mains. When the projector has
cooled down remove the door by unscrewing
the two side screws as well as the metal-
screw (under the objective lens). Unscrew the
screws (4) using a coin. Remove the door by
pulling in the direction of the projected
picture. There is a diagram near the lamps to
indicate the location of each of the lamps.
Now replace the burnt-out lamp. To assist
replacement there is a handle on the neck of
the lamp.
IMPORTANT: Reset the device by pressing
the automatic fuses (15).
Replace the door and fasten the screws. The
projector is now ready for use again.
3
17
A
B
C
5
Produktspecifikationer
| Varumärke: | Reflecta |
| Kategori: | ej kategoriserat |
| Modell: | Episcope A4 |
Behöver du hjälp?
Om du behöver hjälp med Reflecta Episcope A4 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Reflecta Manualer
30 Augusti 2025
30 Augusti 2025
ej kategoriserat Manualer
- Cloer
- Fluidmaster
- Akg
- Kenwood
- RAM Mounts
- Eastron
- RCA
- Avantco
- IOttie
- Orbegozo
- Svan
- Manhattan
- Nilox
- LC-Power
- Markbass
Nyaste ej kategoriserat Manualer
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025
30 Augusti 2025