Rega RB220 Bruksanvisning
Rega
Inte kategoriserad
RB220
Läs gratis den bruksanvisning för Rega RB220 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 9.5 recensioner. Har du en fråga om Rega RB220 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
USER MANUAL
RB
RB
RB
RB
220
INTRODUCTION
The RB220 uses Rega’s custom one piece, aluminium arm tube,
carefully manufactured to optimise performance and reduce
stress on the Rega designed polymer bearings (patent pending).
Each tonearm is meticulously hand assembled using custom
Rega made tools and torque settings to guarantee optimum
performance. This level of care ensures perfect tracking and
maximises the amount of information the cartridge can extract
from the record surface.
The RB220 has adjustable bias allowing greater compatability
with a wide range of cartridges. The Rega designed bias system
will adjust the amount of bias as the tonearm tracks the record
ensuring even tracking during playback.
This Rega tonearm is a precision crafted product. To create
the low friction levels and meet minimum mass requirements,
many parts of the arm are delicate and require careful handling.
The arm should always be treated with respect and under no
circumstances should any part be removed or tampered with.
Any attempt to modify or repair this product, other than by an
ofcial Rega retailer listed on www.rega.co.uk, will invalidate the
lifetime warranty.
ARM BALANCING AND SETUP
With the cartridge tted and aligned using the alignment
protractor supplied, set the bias slider to 0 (with the stylus
guard removed) and screw the balance weight along its shaft (A)
until the stylus is “oating” approximately 1 mm clear of the
record. The recommended tracking force can now be applied by
rotating the balance weight so that it moves towards the front
of the arm. A half turn (through 180 degrees) generates 1 gram
of tracking pressure (turning the weight 360 degrees will apply
2 grams). Use the plastic inserts found on the weight as a visual
guide.
Set the tracking weight to the upper limit of the suggested
tracking weight provided by your cartridge manufacturer’s
guidelines. Once balanced, set the bias slider (A) to the same
gure as the recommended tracking force supplied by your
cartridge manufacturer. Your Rega RB220 tonearm is now ready
for use.
If you have any doubts regarding correct setup or tment of this
arm please contact your ofcial Rega dealer who will be able to
carry out the work for you.
Thank you for purchasing this Rega product and we wish you
many years of musical enjoyment.
A
BALANCE
WEIGHT
CUEING DEVICE
LIFT/LOWER
HANDLE
ARM CLIP
FINGER LIFT
(1:4 scale)
HEADSHELL
PROTRACTOR AND
ARM MOUNTING
DATA INCLUDED.
CUEING
PLATFORM
Produktspecifikationer
| Varumärke: | Rega |
| Kategori: | Inte kategoriserad |
| Modell: | RB220 |
Behöver du hjälp?
Om du behöver hjälp med Rega RB220 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Rega Manualer
26 September 2024
26 September 2024
26 September 2024
23 September 2024
22 September 2024
22 September 2024
21 September 2024
21 September 2024
21 September 2024
21 September 2024
Inte kategoriserad Manualer
- ETA
- Polsen
- Ezviz
- Qualcast
- JVC
- Chicco
- Miracle Smile
- Horex
- ETC
- Chef's Choice
- Mimo Monitors
- Meade
- Vishay
- Hagor
- Leatt
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025