Roland KSC-68 Bruksanvisning
Roland
Inte kategoriserad
KSC-68
Läs gratis den bruksanvisning för Roland KSC-68 (9 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 4 recensioner. Har du en fråga om Roland KSC-68 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
Before using this stand, carefully read the sections entitled “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” Additionally this manual should be saved and
kept on hand as a convenient reference.
Before you begin assembling the stand, check that all the parts were
supplied.
1
2
3
A BC
Owner’s Manual
• Make sure that another person is on hand to help with the assembly and setup.
• Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your
hands or feet.
• Prepare an area in which you can perform the assembly safely.
• Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or
stripping the screws.
• The KSC-68 is designed specically to be used with the F-20.
Assembly Procedure
Parts Check
* You will also need to have a Phillips screwdriver.
* Fasten each screw tightly, then place the stand in a stable and horizontal place.
* Do not allow the pedal cord or power cord to get twisted or pinched while
assembling the stand.
* In the interest of product improvement, the specications and/or appearance of this
stand are subject to change without prior notice.
1 Stand Assembly
At rst, assemble the entire stand in a temporary fashion, without really
tightening the screws. Then, after checking the overall alignment of the
boards (and gently shifting certain parts where necessary), go around and
tightly fasten each of the screws.
1. Attach the side board (left) for the left sides to the center board
(so that the metal parts face inside) using screws “a” (M5 x 20
mm).
2. Use screws “a” (M5 x 20 mm) to attach the side board (right) in
the same way.
1
2
Center board
Side board (left)
Side board (right)
Position the metal
parts of the center
board so that they
face the rear.
Screw “a”
(x 6)
Front
Rear
2 Installing the Piano on the Stand
1. Set the piano on the stand, then rmly attach the four screws
“a” (M5 x 20 mm).
* When handling the piano, rmly grasp it. Be careful, so you do not get your ngers
pinched.
Screw “a” (x 4)
Side board
Underneath the
Piano
Please don’t get your ngers
pinched!
Fasten the screws so
that the stand does not
protrude outward.
3 Attaching the Headphone Hook
1. Attach the headphone hook using screws “b“ (M4 x 16 mm).
Screw “b” (x 2)
Headphone hook
Keyboard stand for F-20 KSC-68
ASide board (left) 1 pcs.
BSide board (right) 1 pcs.
CCenter board 1 pcs.
1Screw “a” (M5 x 20 mm) 10 pcs.
2Headphone hook 1 pcs.
3Screw “b” (M4 x 16 mm) 2 pcs.
* 5 1 0 0 0 3 6 1 4 0 - 0 1 *
IMPORTANT NOTES
Copyright © 2013 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trademark of Roland Corporation in the United States and/or other countries.
USING THE UNIT SAFELY
Deutsch Français Italiano Español Português NederlandsEnglish
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices About the Symbols
ALWAYS OBSERVE THE FOLLOWING
Do not disassemble or modify by yourself
Do not carry out anything unless you
are instructed to do so in the owner’s
manual. Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer, the
nearest Roland Service Center, or an
authorized Roland distributor, as
listed on the “Information.”
Do not use or store in the following types of
locations
• Subject to temperature
extremes (e.g., direct sunlight
in an enclosed vehicle, near
a heating duct, on top of
heat-generating equipment);
or are
• Damp (e.g., baths, washrooms,
on wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness.
Do not place in an unstable location
Otherwise, you risk injury as the
result of the stand toppling over or
dropping down.
Be cautious to protect children from injury
Always make sure that an adult is on
hand to provide supervision and
guidance when using the stand in
places where children are present, or
when a child will be using the stand.
Do not drop or subject to strong impact
Otherwise, you risk causing damage
or malfunction.
CAUTION
Use the stand only for the specied products
This stand is designed specically to
be used with the Roland F-20. If
used in combination with other
products, you risk sustaining injuries
as the result of the product dropping down or
toppling over due to a lack of stability.
Evaluate safety issues before using stands
Even if you observe the cautions
given in the owner’s manual, certain
types of handling may allow F-20 to
fall from the stand, or cause the
stand to overturn. Please be mindful of any
safety issues before using this product.
Avoid climbing on top of the stand, or placing
heavy objects on it
Otherwise, you risk injury as the
result of the stand toppling over or
dropping down.
Keep small items out of the reach of children
To prevent accidental ingestion of
the parts listed below, always keep
them out of the reach of small
children.
• Removable Parts
Screw
WARNING
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US (Proposition 65)
WARNING
Placement
• Do not expose the stand to direct sunlight,
place it near devices that radiate heat, leave
it inside an enclosed vehicle, or otherwise
subject it to temperature extremes. Also, do
not allow lighting devices that normally are
used while their light source is very close to
the stand (such as a piano light), or powerful
spotlights to shine upon the same area of the
stand for extended periods of time. Excessive
heat can deform or discolor the stand.
• Do not allow rubber, vinyl, or similar materi-
als to remain on this stand long periods of
time. Such objects can deform or discolor the
stand.
• Do not paste stickers, decals, or the like
to this stand. Peeling such matter o the
instrument may damage the exterior nish.
• Depending on the material and temperature
of the surface on which you place the stand,
its rubber feet may discolor or mar the
surface.
You can place a piece of felt or cloth under
the rubber feet to prevent this from happen-
ing. If you do so, please make sure that the
stand will not slip or move accidentally.
Maintenance
• To clean the stand, use a dry, soft cloth; or
one that is slightly dampened. Try to wipe
the entire surface using an equal amount of
strength, moving the cloth along with the
grain of the wood. Rubbing too hard in the
same area can damage the nish.
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility
of discoloration and/or deformation.
• As with any wood-crafted product, some
expansion and contraction of the wood
can occur depending on the way the stand
is used and the environment in which it
is used. Over time, this can cause some of
the screws to start coming loose. To ensure
safe, worry-free use of the stand, you should
periodically check the tightness of the screws
shown in the illustrations in the “Assembly
Procedure.” If you nd any that are loose, use
a screwdriver to tighten them.
DeutschFrançaisItalianoEspañolPortuguêsNederlands English
11
Produktspecifikationer
| Varumärke: | Roland |
| Kategori: | Inte kategoriserad |
| Modell: | KSC-68 |
Behöver du hjälp?
Om du behöver hjälp med Roland KSC-68 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Roland Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
2 April 2025
Inte kategoriserad Manualer
- Tesy
- Monoprice
- Essenza
- Grotime
- Loewe
- SEB
- The Grainfather
- Monitor Audio
- Lowell
- Soundmaster
- Indiana Line
- Aerial
- Livarno Lux
- IMG Stage Line
- Serge
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025