Sanyo LCD-27XA2 Bruksanvisning
Läs nedan 📖 manual på svenska för Sanyo LCD-27XA2 (28 sidor) i kategorin LCD TV. Denna guide var användbar för 18 personer och betygsatt med 4.5 stjärnor i genomsnitt av 9.5 användare
Sida 1/28

INSTRUCTION MANUAL
LCD Colour Television
LCD-27XA2
LCD-32XA2
P
Please read this Instruction Manual before using your television.
We wish you many hours of pleasure from your new television.
Downloaded From TV-Manual.com Manuals

2
2
Warnings and Cautions
Minimum Distances
5 cm
10 cm
10 cm
10 cm
Warning
High voltages are used in the operation of this
television receiver. Do not remove the cabinet
back from your set. Refer servicing to quali-
fied service personnel.
Do not drop or push objects into the televi-
sion cabinet slots or openings.
Never spill any kind of liquid on the television
receiver.
Caution
Avoid exposing the television receiver to direct
sunlight and other source of the heat.
If the television is to be built into a compartment
or similarly enclosed, the minimum distances
must be maintained. Heat build-up can reduce the
Do not block the ventilation holes in the back
cover. Adequate ventilation is essential to prevent
failure of electrical components
.
Cleaning the TV Monitor
Do not press Do not hit
Be sure to disconnect the AC Power Cord from
AC outlet before cleaning the TV monitor.
Gently wipe the screen
and cabinet with dry soft
cloth. Screen is likely dam-
aged if it is not maintained
properly. Do not use hard
cloth or paper. Do not use
solvents or abrasive.
Do not use benzene, thin-
ner or any volatile sub-
stances to clean the TV
monitor. These chemicals
may damaged the cabinet
finish.
Caution
Care for Using TV Monitor
Screen likely damaged by external shock. When
using the TV monitor, following precautions
should be taken.
Do not press or hit the screen face.
Do not write, paint or affix anything on the screen.
Do not put anything on the TV monitor.
service life of your television, and can also be
dangerous.
If the LCD panel is broken and leaks liquid
crystal, do not touch it. Moreover, never swal-
low or suck the liquid, or touch the liquid with
your skin. In case the liquid drops in your
mouth or eyes, clear it by water adequately at
once and go to see a doctor. If not, there is a
possibility causing poisoning. If the liquid
drops on skin or clothes, also clear it by water
adequately at once, if not, the skin or clothes
will be damaged.
To prevent fire or electrical shock hazard, do
not expose the television receiver to rain or
moisture.
Downloaded From TV-Manual.com Manuals

ANT.75Ω
Installation
3
3
Step 1 : Connecting the Aerial and Power Supply
•Connect your aerial cable plug to the rear of the TV set.
For further information please consult your local dealer.
•Connect the AC power plug to the wall socket (AC100-264 Volts, 50Hz/60Hz).
Note: The form of the AC code and AC plug are different with each country.
Downloaded From TV-Manual.com Manuals

4
4
Installation
Step 3 : Switching on/Plug & Play
Use 2 “AAA” 1.5 volt batteries.
Be sure batteries are installed correctly.
Note: Do not mix old batteries with new ones or mix different type of batteries together.
Step 2 : Battery Installation of the Remote Control Transmitter
Let’s start !
Let’s start !
This TV set provides a self-automatic tuning system function called “Plug & Play”.
It automatically begins searching and storing of all available channels when switching-on the
TV set for the first time.
1 1Press the Power ON/OFF button to turn the TV on, and the TV set will search and store of
all available TV channels automatically.
2 2After completing Plug & Play, press the MENU button to return to the normal TV mode.
✐ This procedure only appears at the first switch-on time.
Now the installation is completed !
Downloaded From TV-Manual.com Manuals

Control Panel
5
5
P
Each button listed this section has the same function as it’s corresponding button on the
Remote Control
Programme
Up/Down Power ON/OFF
button
Remote Control
Detector
Stand-by and
Power Indicator
Volume
P
360˚
Do not position hand under the screen frame
while rotating the TV.
Caution
Viewing Angle Adjustment
Swivel stand is rotated 360˚ right and left.
Downloaded From TV-Manual.com Manuals

CS
6
6
Remote Control Transmitter
TV/AV Selector
Recall/Colour System
Numeric buttons
Digit
TEXT/TV
Stereo/Mono
BASS
Power ON/OFF
Sound Mute
Wide
Alternate
Volume +/
-
Picture Mode
SURROUND
MENU
To select the next or previ-
ous programme position.
Digital Shot
TIMER
DVD button
Programme Up/Down
Sound Mode
CS button
OK button
Cursors
These buttons are not used.
VCR and DVD button
To call up the List screen of
the Digital Shot.
To increase or decrease the
sound volume level.
Press repeatedly to switch to
TV, AV1, AV2, AV3, AV4 or
AV5 mode.
Red
Green
Yellow Blue
To call up the Timer menu
directly.
To select half mute, full
mute or restore the sound.
Downloaded From TV-Manual.com Manuals

7
7
General Operation
Press the Power ON/OFF button to
turn on or off (Stand-by) the TV set.
Power ON/OFF(Stand by)
Power ON/OFF(Stand by)
Auto Shut Of
Auto Shut Of f Function
f Function
Alter
Alternate
nate
Press the utton, and theAlternate b
programme position will alternately
select the previous position and the
present position.
Pictur
Picture Mode Selection
e Mode Selection
Press the Picture Mode button
repeatedly to select the following
picture modes;
Personal : Yo ur personal preference mode.
Standard: Normal viewing mode.
Dynamic: Suitable for brightly lit room.
You can turn on the TV in the standby mode
by pressing the following buttons in addition
to the Power ON/OFF button.
● Programme Up/Down button of the
remote control transmitter or the TV set.
● 1 9to , 0 button on the remote control
transmitter.
If the TV is left on after you have gone to
sleep, the TV set changes to the standby
mode within 10 minutes after all broadcasts
have ended.
Lighting of the Stand-by and Power Indicator
shows that there is a power supply. For shut-
ting off a power supply completely, discon-
nect the power cord from the power outlet.
Bass Expander On/Of
Bass Expander On/Of f
f
Press the BASS button to get an
emphasised bass sound.
Press the Sound Mode button
repeatedly to select the following
sound modes;
Personal:
Your personal preference mode
.
Music: Suitable for music programme.
Talk: Suitable for news programme.
Normal: Normal listening mode.
Sound Mode Selection
Sound Mode Selection
Active 3D Surr
Active 3D Surround
ound
Press the SURROUND button to
switch 3D Surround on (Active)
and off.
Dir
Direct Pr
ect Programme Selection
ogramme Selection
Example:
■Press 6button to select programme
position 6.
■ To select programme position 27, press
the Digit button, press 0, 2then utton.7b
or
Press the Digit button, press 2 7, button
and wait for 5 seconds.
■ To select programme position 215, press
the DIGIT b ,utton, press 2 1 then
5button.
-/- -
-/- -
-/- -
-/- -
-/- --/- -
-/- -
-/- -
-/- -
-/- -
-/- --/- -
-/- -
-/- -
-/- -
-/- -
-/- --/- -
Downloaded From TV-Manual.com Manuals

8
8
General Operation
Pr
Programme Infor
ogramme Information Call
mation Call
To display the on screen indication, press
the Recall/Colour System button.
A2 Ster
A2 Ster eo, NICAM Ster
eo, NICAM Stereo
eo
and Bilingual Br
and Bilingual Br oadcast
oadcast
Receiving
Receiving
■A2
Stereo and NICAM Stereo sound
reception
■ Bilingual reception
If the TV receives bilingual programs, the
TV initially selects language A and displays
“A” on the screen briefly. If you want to
switch to language B or Mono (only avail-
able in NICAM reception), press the Stereo/
Mono button.
A2 Bilingual
When receiving NICAM stereo broadcast,
NICAM will be displayed on the screen. For
A2 (German) stereo broadcasts, Stereo will
be displayed. When a clear stereo sound
can not be obtained during NICAM or A2
(German) stereo broadcast due to poor
signal reception, press the Stereo/Mono
button to select mono mode.
NICAM Stereo
A2 Stereo
NICAM Bilingual
Sound Status
Off-timer
Programme Position
Sound System
OFF 02:00
Mono
A
NICAM
AUTO
BG
Colour System Selection
Colour System Selection
If the clear picture cannot be obtained, press
the Recall/Colour System button repeated-
ly until optimum image can be produced.
SECAM
NTSC4.43
A colour system entry to the memory can
not be made during TV mode, make it
during Semi-auto tuning mode.
NTSC
PALAUTO
Colour System
Stereo
NICAM
Mono
B
Mono
A
B
03
Downloaded From TV-Manual.com Manuals

Auto
It automatically switches to the optimum screen mode according to the signal providedWSS
in the receiving signal source. If the signal does not have it, the TV keeps current screen mode.
This setting may cause the picture to change when a different format is received e.g. when an
advert is received.
WSS (Wide-Screen-Signalling)
This function is to be automatically set to the optimum screen mode for the wide screen
television according to the aspect ratio bits of the picture format (16:9, 14:9, 4:3, etc.) on
the receiving signal source. To use this function, the picture mode should be selected to
the “Auto” mode. This function is also effective in the AV mode. When you connect AV
equipment which has the function, the screen mode is automatically selected to the WSS
optimum screen mode.
Press the Wide button to select the following screen modes;
Auto / Natural Full/ Zoom 14:9 / Title-in 14:9 / Zoom 16:9 / Title-in 16:9 / /
Normal
General Operation
9
9
Natural
Scr
Screen Mode Selection
een Mode Selection
Today there are various transmission formats with different size ratios, e.g. 4:3, 14:9, 16:9
and video format such as letterbox. 4:3 picture sometimes have a black band at the top and
bottom of the screen. You can select a screen mode to optimise the picture display.
4:3 14:9 16:9 Letterbox Video
Stretches the picture
horizontally to fill the
screen, the picture is
more stretched at the
edges.
The height is expand-
ed to fill the whole
screen.
The picture fills the
screen and is propor-
tionally correct.
The black bars top
and bottom remain
and the height is
compressed to fit into
the picture area.
Downloaded From TV-Manual.com Manuals

10
10
General Operation
Title-in 14:9
Zoom 16:9
Zoom 14:9
4:3 14:9 16:9 Letterbox Video
The correct picture
width is maintained
but the top and
bottom are cropped.
Zooms in slightly
cropping the top and
bottom.
Zooms in slightly
cropping the top and
bottom.
The black bars top
and bottom are small-
er and the picture
height is compressed
slightly.
TITLES ON SCREEN TITLES ON SCREEN
TITLES ON SCREEN TITLES ON SCREEN
4:3 14:9 16:9 Letterbox Video
As zoom (14:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As zoom (14:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As zoom (14:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As zoom (14:9), but
bottom is compressed
even more to allow
subtitles to be seen.
4:3 14:9 16:9 Letterbox Video
The correct picture
width is maintained
but the top and bot-
tom are cropped.
Zooms in slightly
cropping the top and
bottom.
Zooms in slightly
cropping the top and
bottom.
The black bars top
and bottom are small-
er and the picture
height is compressed
slightly.
Downloaded From TV-Manual.com Manuals

General Operation
11
11
Title-in 16:9
Full
Normal
TITLES ON SCREEN TITLES ON SCREEN TITLES ON SCREEN TITLES ON SCREEN
4:3 14:9 16:9 Letterbox Video
As Zoom (16:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As Zoom (16:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As Zoom (16:9), but
bottom is compressed
even more to allow
subtitles to be seen.
As Zoom (16:9), but
bottom is compressed
even more to allow
subtitles to be seen.
4:3 14:9 16:9 Letterbox Video
The whole screen is
filled stretching the
width.
The whole screen is
filled stretching the
height slightly at the
edges.
The whole screen is
filled with the correct
picture ratio.
The black bars top
and bottom are bot-
tom are present and
the height is
compressed.
4:3 14:9 16:9 Letterbox Video
The correct ratio is
maintained with black
bars on the left and
right.
Black bars left and
right, picture
height is
stretched.
Black bars left and
right, picture
height is
stretched.
Black bars left, right,
top and bottom.
Downloaded From TV-Manual.com Manuals

12
12
General Operation
Use Digital Shot function to capture and
save the up to 12 pictures and replay them in
a list mode, full screen mode and automatic
album mode.
Digital Shot
Digital Shot
How to capture the pictures
11Press the Digital Shot button to capture
a scene that you want to store.
(The screen is not frozen at this time.)
1 / 12
1 / 12
1 / 12
1 / 12
1 / 121 / 12
Up to 12 frozen pictures can be stored.
12 / 12
12 / 12
12 / 12
12 / 12
12 / 1212 / 12
“Memory Full” will be displayed for a few
seconds when 12 pictures are stored.
Memory Full
Memory Full
Memory Full
Memory Full
Memory FullMemory Full
2 2Select a picture that you want to display
with the cursor / or /
button.
3 3Press the OK button to display.
4 4To return to the normal TV mode, press
the CS button.
To return to the List mode:
Press the Blue button.
CS
: Delete All
: Auto Album
: Exit
: Delete
: Select
CS
OK
1
1
1
11
To replay only the selected picture
1
1Press the utton to display the screenCS b
of List mode.
: Delete All
: Auto Album
: Exit
: Delete
: Select
CS
OK
12
12
12
12
1212
: Delete All
: Auto Album
: Exit
: Delete
: Return
CS
: Delete All
: Auto Album
: Exit
: Delete
: Return
CS
To display guide menu:
Press the OK button. To erase guide menu,
press the OK button again.
Downloaded From TV-Manual.com Manuals

General Operation
13
13
CS
: Delete All
: Auto Album
: Exit
: Delete
: Select
CS
OK
1
1
1
11
Auto Album
Use this function to display each picture
continuously.
1 1Press the utton to display the screenCS b
of List mode.
2 2Press the utton, and each Green b
picture is displayed continuously every
three seconds.
To stop Auto Album on the way:
Press the Green button.
(To start Auto Album again, press the
Green button again .)
or
Press the OK button.
(To display guide menu, press the OK button
again.)
To return to the List mode:
Press the Blue button.
To return to the normal TV mode:
Press the CS button.
(When the TV/AV Selector is pressed, TV
return to the AV mode.)
CS
: Delete All
: Auto Album
: Exit
: Delete
: Select
CS
OK
1
1
1
11
Deletion of pictures
1 1Press the utton to display the screenCS b
of List mode.
2 2Select a picture that you want to delete
with the cursor / or /
b button. Then press the Yellow utton.
2) Press the Red button again.
(To cancel deletion, press the Blue
button.)
Delete All ?
Delete All ?
Delete All ?
Delete All ?
Delete All ?Delete All ?
: Delete
:
:
:
:: Delete
Delete
Delete
Delete Delete : Cancel
:
:
:
:: Cancel
Cancel
Cancel
Cancel Cancel
To delete all pictures at a time:
1) Press the utton in the List Red b
mode.
: Delete All
: Auto Album
: Exit
: Delete
: Select
CS
OK
9
9
9
99
No Image
No Image
No Image
No Image
No ImageNo Image
Downloaded From TV-Manual.com Manuals

14
14
Note:
Your picture adjustment will be memorized
to “Personal” of the Picture Mode automati-
cally.
4 4Once the adjustments have been
completed, select “Memory” and press
OK button to store the settings.
Press the MENU button to exit.
Picture Adjustments
3 3Press or to adjust.
Menu Operation
Sound Adjustments
The on-screen menu provides the viewer
with easy access to adjustments and
settings. Follow the on-screen instruction at
the bottom of the screen.
■During the menu operation, the following
buttons are used.
MENU
To call up the menu.
To exit the menu.
To move around the menus.
To make adjustments.
Picture
Picture
Picture
Picture
PicturePicture
Contrast
Colour
Sharpness
Tint
Text Brightness
Brightness
Memory
Preset
Setting
Sound
P
P
Timer
To move around
the menus.
Picture
Picture
Picture
Picture
PicturePicture
Contrast
Colour
Sharpness
Tint
Text Brightness
35
36
44
52
Centre
OK?
Memory
32
Brightness
2 2Press to select a content.
•
•
•
••
Tint :
Adjust colour tints. (Displayed only on
NTSC signal reception.)
•
•
•
••
Text Brightness :
Brightness of teletext screen (Minimum,
Centre, Maximum).You can not control
the picture and the teletext brightness in
the teletext mode. You must first switch
back to the TV mode and then adjust the
picture control or set the teletext bright-
ness level.
1 1Press the utton, and select MENU b
“Sound” menu with or .
2 2Press to select a content.
: Select : Contents MENU : Exit
OK button
To store the settings.
1 1Press the utton, and select MENU b
“Picture” menu with or .
Downloaded From TV-Manual.com Manuals

15
15
Menu Operation
•
•
•
••
Balance :
Left and Right speaker volume balance
adjustment.
•
•
•
••
BBE (ON/OFF)
Enable to switch the BBE sound turn on
and off. BBE High Definition Sound
restores clarity and presence for better
speech intelligibility and musical realism.
•
•
•
••
Auto Volume (ON/OFF) :
This function automatically equates the
sound volume of each position. It is used
to prevent the sharp volume change when
you change the channel.
Sound
Sound
Sound
Sound
SoundSound
Bass
Treble
Balance
BBE
0
20
5
ON
Auto Volume OFF
23Volume
3 3Press or to adjust.
4 4Press the utton to exit.MENU b
Sound settings will be automatically
stored when you exit the menu.
Timer Setting
1 1Press the utton, and select MENU b
“Timer” menu with or .
(To display “TIMER” menu directly, press
the TIMER button on the remote control.)
2 2Select “OFF timer” with .
Timer
Timer
Timer
Timer
TimerTimer
Alarm Timer
OFF Timer
-
-
:
-
-
-
-
:
-
-
When the TV set is turned off, Off Timer setting
will be cancelled.
The time changes in 30 minutes steps.
The maximum time is 2 hours.
When the time period is up, the time up
sign will appear on the screen and the
alarm will sound for about 15 seconds.
■Alarm timer setting
The alarm will ring for about 15 seconds
when you are watching the television and it
reaches at the set-up time. It may remind
you to do something. (This only happens
when the TV is switched on.)
■Off timer setting
The Off timer will switch the TV set into the
standby mode when the selected time has
elapsed.
3 3Press or to select “
--
:
--
” .
4 4Press or to set OFF timer.
5 5Press or to make row of OFF
timer complete yellow.
6
6
Press the OK button to store the setting
.
Press the utton to exit, or press MENU b
to set alarm timer.
Timer
Timer
Timer
Timer
TimerTimer
OFF Timer
-
-
:
-
-
-
-
:
-
-
Alarm Timer
The time changes in 5 minute steps.
The maximum time period is 3 hours.
2 2Press or to select “
--
:
--
” .
3
3Press or to set Alarm timer.
5
5
Press the OK button to store the setting
.
Press MENU button to exit.
To stop the alarm sound and
to erase alarm sign, press
one of the buttons of the
remote control or TV set.
4 4Press or to make row of Alarm
timer complete yellow.
When the TV set is turned off, Alarm timer
will be cancelled.
1 1Select “Alarm timer” with in the
Timer menu.
Downloaded From TV-Manual.com Manuals

16
16
Preset Menu
Use Preset Menu to tune new channels, to
re-order channels and their programme
positions, and to make fine tuning.
Up to 255 broadcast stations can be stored.
Auto T
Auto Tuning
uning
Menu Operation
Setting Menu
1 1Press the MENU then or button to
select “Setting” menu.
Setting
Setting
Setting
Setting
SettingSetting
Noise Reduction
Teletext Language
OSD Language
AV2
Child Lock OFF
A
Min
Video
English
3 3Press or to set each option.
4 4Press the utton to exit.MENU b
These settings will be automatically
stored when you exit the menu.
Preset
Preset
Preset
Preset
PresetPreset
Prog. Preset
Swap
Fine Tuning
Auto Tuning >
P
P
>
-
-
-
< >
1 1Press the utton, and select MENU b
“Preset” menu with or .
2 2Select “Auto Tuning” with .
3 3Press to enter the Auto Tuning mode,
and “Frequency” will be selected first.
P
P
Auto
A
A
A
AAuto
uto
uto
utouto
System
Sound
Frequency
007
Auto
BG
Position
271.65 MHz
•
•
•
••
System (Colour System):
You can change the colour system
with or .(Auto, PAL, SECAM,
NTSC4.43 or NTSC.)
•
•
•
••
Sound (Sound System):
You can change the sound system
with or .(BG, DK, I or M.)
Auto Tuning can be cancelled at any time by
pressing the MENU button.
5 5Press the utton to exit.MENU b
This setting menu gives you several options
to adjust.
4 4Press to start tuning.
All the available stations are automati-
cally stored, starting from position 1.
After completing this procedure, TV set
returns to programme position “1”.
•
•
•
••
Child Lock (ON, OFF):
You can prevent that a small child
operates television with the front control
button of the TV set. When the power plug
is pulled out, this function is cancelled.
•
•
•
••
Noise Reduction :
(Displayed only on TV mode.)
You can choose noise reduction
mode; OFF, Min, Med or Max.
•
•
•
••
Teletext Language :
You can choose your text language, select
A or B.
A=English, Arabic and Cyrillic.
B=English, Persian and Cyrillic.
•
•
•
••
OSD Language :
This is useful if you wish to change the
On-screen display language (
English,
, Dutch, Suomi, Deutsch, Hrvatski,
Dansk, Greek, Magyar, Italiano, Polski,
Português, Español, Svenska or Cesky
).
•
•
•
••
Setting of AV2 input mode :
When you use a S-VHS VCR, you should
connect it to AV2 and change the AV2
menu to “S-Video”.
2 2Press to select a content.
Downloaded From TV-Manual.com Manuals

17
17
Menu Operation
Semi-auto T
Semi-auto Tuning
uning
This is used to preset a channel in any pro-
gramme position.
1 1Select “Prog. Preset” with in the
Preset menu.
Preset
Preset
Preset
Preset
PresetPreset
Swap
Fine Tuning
Auto Tuning >
P
P
< >
Prog. Preset >
-
-
-
Semi
Semi
Semi
Semi
SemiSemi
Sound
P
P
System
BG
Auto
007Position
Frequency 271.65 MHz
Fine T
Fine Tuning
uning
Preset
Preset
Preset
Preset
PresetPreset
Swap
Auto Tuning >
P
P
Prog. Preset >
Fine Tuning < >
-
-
-
2
2Press and hold or to fine tune a
channel.
3
3Press the utton to exit.MENU b
The tuning will be stored when you exit
the menu.
Any changes made by fine tuning will
remain even when the TV set is turned off.
3 3Select “Position” with .
To select desired programme position:
Press the Digit (-/--) button and enter
the position number (000-254) using 0-9
buttons.
or
Press to select programme
position sequentially.
6 6Select “Memory” with , and press the
OK button to memorize.
7
7Press the utton to exit.MENU b
Repeat steps 3-6 to store other channels in
other programme positions.
•
•
•
•• If the clear picture cannot be obtained,
change the colour system with or .
•
•
•
•• If the sound is not clear or no sound is
produced, change the sound system
with or .
1
1Select “Fine Tuning” with in the
Preset menu.
2 2Press to enter the Semi-auto Tuning
mode.
Semi
Semi
Semi
Semi
SemiSemi
Sound
Skip
P
P
System
Memory OK?
OFF
BG
Auto
010Position
Frequency 273.25 MHz
5
5You can either...
a) -/--Press the Digit ( ) button, and enter
the frequency (5 digits) using 0-9
buttons referring channel table.
b) Press and release (toward the lower
frequency) or (toward the higher
frequency) to search a TV station.
Once a station is found, tuning will stop
automatically. Repeat until desired
station is found.
Semi
Semi
Semi
Semi
SemiSemi
Sound
Skip
P
P
System
Memory OK?
OFF
BG
Auto
010Position
Frequency 273.25 MHz
4 4Select “Frequency” with .
Downloaded From TV-Manual.com Manuals

18
18
Menu Operation
1 1Select programme position eg. 3.
Preset
Preset
Preset
Preset
PresetPreset
Auto Tuning >
P
P
Prog. Preset >
Fine Tuning < >
Swap
-
-
-
4 4Press the OK button to memorize, and
the programme number disappears.
The channels are now swapped.
5 5Press the utton to exit.MENU b
Channel Swapping
Channel Swapping
Use this feature to swap the channels
between two stored programme positions.
This feature is particularly useful after auto-
matic tuning.
First of all, you have to select a programme
position you wish to swap. eg. swap pro-
gramme position 3and 12.
2 2Call up the Menu display, and select
“Swap” of the Preset menu with .
3 3Enter new programme position number
eg. , n12 by pressing 0 1 and 2 umeric
buttons.
Setting of the Skip Channels
Setting of the Skip Channels
If there are positions you do not use, by set-
ting skip channel function, it is possible to
jump over any position when you are select-
ing a channel using the Programme Up/
Down button.
1 1Select “Position” in the Semi menu.
Semi
Semi
Semi
Semi
SemiSemi
Sound
Skip
P
P
System
Memory OK?
OFF
BG
Auto
007
Position
Frequency 271.65 MHz
3 3Select “Skip” with , and set Skip “ON”
with or .
(To cancel skip channel, set Skip “OFF”.)
4 4Select “Memory” with , and press the
OK button to memorize.
5
5Press the utton to exit.MENU b
2 2Select programme position you want to
skip.
To select desired programme position:
Press the Digit (-/--) button and enter
the position number (000-254) using 0-9
buttons.
or
Press to select programme
position sequentially.
AUTO
BG
Semi
Semi
Semi
Semi
SemiSemi
Sound
P
P
System
Memory OK?
ON
BG
Auto
010Position
Frequency 273.25 MHz
Skip
03
Downloaded From TV-Manual.com Manuals

19
19
Setting of the Hotel Mode
The Hotel Mode is a feature that might be
needed by a hotel management to confine
the TV that put in the hotel room, so it will
not disturb other rooms.
Setting Procedure
1 1Set the desired maximum sound volume
by pressing the Volume + or
-
button.
P
P
P
P
PP
r
r
r
r
rr
o
o
o
o
oo
h
h
h
h
hh
i
i
i
i
ii
b
b
b
b
bb
i
i
i
i
iit
t
t
t
tti
i
i
i
iio
o
o
o
oon
n
n
n
nnO
O
O
O
OON
N
N
N
NN
Start-Position OFF
2 2Press and hold the Recall/Colour
System button on the remote control
and press the Programme Up button
on the TV set.
3
3 Select desired item with or , and
set the option with or .
4 4Press the Recall/Colour System button
to exit.
•
•
•
••
Prohibition (ON, OFF):
Current volume will be set as the maxi-
mum volume, and channel tuning is
prohibited.
•
•
•
••
Start-Position :
Setting of the start up programme
position when the TV is turned on.
OFF: Last programme position start.
P1: Programme position “1” start.
P2: Programme position “2” start.
P3: Programme position “3” start.
P4: Programme position “4” start.
P5: Programme position “5” start.
P6: Programme position “6” start.
P7: Programme position “7” start.
P8: Programme position “8” start.
AV1: “AV1” start.
Downloaded From TV-Manual.com Manuals

20
20
CS
Teletext Operation
Sub page access
Some text pages are made up
of several sub pages which
rotate automatically. If you
wish to view page-4, press the
Sub Page button, and “S----”
will appear. Then enter “0004”
using bNUMERIC uttons.
Teletext / TV selector
To switch TV, TEXT and PAT
(Picture and Teletext) mode.
Direct access to subject
headings
Coloured boxes are displayed
at the bottom of the screen.
The 4 coloured buttons give
access to the corresponding
subjects or pages.
Index page selector
To select one of the teletext
index pages.
Size switch
Either the top half or the
bottom half of the page can
be expanded.
Up/down page access
To select the next or previous
page number.
Reveal switch
To reveal hidden items on the
text page e.g. a hidden
answer to a quiz question.
Direct access to a page
To select a page number
directly using the (0-9)
NUMERIC buttons. For exam-
ple, to select page 301, press
3, then 0 and then 1.
Hold
To stop sub pages from changing.
Teletext language selection
You can select a teletext language. Please return to the TV mode. (See Setting menu.)
Teletext brightness level
You can change the teletext brightness level. Please return to the TV mode. (See Picture
Adjustments.)
Sound volume control in teletext mode.
In teletext mode, sound volume and sound muting can be controlled. However they are not
displayed on the screen
Teletext reception
If your aerial signal is poor, the teletext reception may be poor.
Cancel
To view the TV picture in the
teletext mode while waiting for
sub page to change or page
to update. Press again to
return to teletext mode. (Note:
The page number will appear
when the page is updated.)
TELETEXT
DISPLAY
(Picture and Teletext mode)
Downloaded From TV-Manual.com Manuals

VCR and DVD Use
21
21
This remote control transmitter has been designed to be used in conjunction with selected
SANYO VCR’s and DVD players. Some SANYO VCR’s and DVD players may have their own
functions, so please refer to the individual instruction booklet when using this remote control
to ensure compatibility. Some of the buttons are used for both the VCR and DVD player. The
symbols indicated with blue are for the buttons to control the DVD player. When use the DVD
player with this remote control, first press and hold the DVD button and then press your
desired control button each time.
VCR DVD
Not used DVD command mode selection
Power Power
Play Play
pause Pause
Stop Stop
Fast/Cue Next chapter selection
Rewind/Review Previous chapter selection
Record, press both buttons Not used
at the same time
Not used Enter
Not used Cursor selection
Downloaded From TV-Manual.com Manuals

22
22
AV Terminals
VIDEO
AV4
AUDIO
L
R
AV1AV2
AV3
AUDIO MONITOR OUT
LR
AV5
Y
CB
CR
AUDIO
L
R
L
R
VIDEO
L
R
VIDEO
DVD INPUT
Audio Video
Input Jacks (AV4)
DVD Input (Component Video Input and Audio Input jacks) (AV5)
Headphone Jack
(Mini Stereo Jack)
For personal listening, a head-
phone can be connected to the
headphone jack.
Audio Monitor Output Jacks
Audio Video Input Jacks (AV1)
Scart Terminal (AV2)
Input: Composite video, RGB, S-video and audio-L/R
Output: Monitor-output with composite video and audio-L/R
Audio Video Input Jacks (AV3)
Side Terminal
Rear Terminal
Downloaded From TV-Manual.com Manuals

Connecting Other Equipment
23
23
You can connect a VCR, S-VHS VCR, Satellite Tuner, PAY TV Decoder, DVD or Camcoder to
this TV via the AV terminals and the SCART terminal.
■Depending on the type of video tape or connected AV equipment being used, it may be
necessary to select colour system. In this case, press the Recall/Colour System button
and select a suitable colour system. Colour system setting for AV position is automatically
stored in the memory.
■By pressing the Stereo/Mono button repeatedly, you can select the sound track L
(left), R (right) or L/R.
■ You can select and return to a TV programme by selecting any of the TV position while
watching a playback from a VCR, DVD, etc.
■Select “AV2” mode by pressing the TV/AV Selector for watching.
S-Video Connection through Scart Terminal Adaptor
AV1AV2
AV3
AUDIO MONITOR OUT
L R
AV5
Y
CB
CR
AUDIO
L
R
L
R
VIDEO
L
R
DVD INPUT
DVD
R-AUDIO - L/MONO VIDEO S-VIDEO
When you use a S-VHS VCR not provided with the 21-pins scart terminal, connect it with the
AV2 terminal using Scart Terminal Adaptor, and set AV2 status on “S-Video” (Refer to the
Setting Menu on page 16).
S-VHS VCR
Scart Terminal Adapter
(Supplied with TV set)
PLAYBACK
DVD Player etc.
To audio output
To S-Video output
Important Note:
Do not input to both S-Video and RCA video input jack of the Scart Terminal Adaptor at the
same time to avoid signal mix and distorted picture.
S-Video Jack
Downloaded From TV-Manual.com Manuals
Produktspecifikationer
Varumärke: | Sanyo |
Kategori: | LCD TV |
Modell: | LCD-27XA2 |
Behöver du hjälp?
Om du behöver hjälp med Sanyo LCD-27XA2 ställ en fråga nedan och andra användare kommer att svara dig
LCD TV Sanyo Manualer

21 Oktober 2024

18 Oktober 2024

14 Oktober 2024

15 September 2024

15 September 2024

31 Juli 2024

30 Juli 2024

28 Juli 2024
LCD TV Manualer
- LCD TV Tesco
- LCD TV Tevion
- LCD TV Opera
- LCD TV Loewe
- LCD TV Hitachi
- LCD TV Toshiba
- LCD TV Fujitsu Siemens
- LCD TV VISIONQUEST
- LCD TV SEIKI
- LCD TV Continental Edison
- LCD TV AOC
- LCD TV Wharfedale
- LCD TV Grundig
- LCD TV Sansui
- LCD TV Technika
Nyaste LCD TV Manualer

9 April 2025

5 April 2025

13 Mars 2025

12 Mars 2025

12 Mars 2025

7 Mars 2025

25 Januari 2025

16 Januari 2025

15 Januari 2025

11 Januari 2025