Sauter TB 2000-0.1F Bruksanvisning
Sauter
Mätutrustning
TB 2000-0.1F
Läs gratis den bruksanvisning för Sauter TB 2000-0.1F (7 sidor) i kategorin Mätutrustning. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 5.5 recensioner. Har du en fråga om Sauter TB 2000-0.1F eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction Manual Digital Coating
Thickness Gauge
SAUTER TB
Version 2.0
04/2020
GB
TB- -e-2020 BA
PROFESSIONAL MEASURING
2 - -e-2020 TB BA
GB
SAUTER TB
V. 2.0 04/2020
Instruction Manual Digital Coating Thickness
Gauge
Thank you for purchasing a digital coating thickness gauge from SAUTER. We hope
you will be very satised with the high quality of this measuring device and its extensive
functionality. For any questions, wishes and suggestions please do not hesitate to
contact us.
Table of contents:
1. Introduction .................................................................................................... 3
1.1 General description .................................................................................................................. 3
2. Functions ........................................................................................................ 3
3. Technical data ................................................................................................ 4
4. Description of the control panel ................................................................... 5
5. Measuring procedure .................................................................................... 5
6. Oset-Accur ................................................................................................... 5
7. Calibration (Adjustment) ............................................................................... 6
8. Battery replacement ...................................................................................... 6
9. Adjusting foils ................................................................................................ 6
10. Correct handling of coating thickness measurement with external sensors
7
11. Troubleshooting 7 .............................................................................................
TB- -e-2020 3 BA
1. Introduction
1.1 General description
This coating thickness gauge is small, light and handy. Although it has complex and
advanced equipment, it is convenient and easy to use.
Its robustness allows it to be used for many years, provided that all instructions in this
manual are carefully followed.
Therefore, please keep them always within reach!
Note: It is strongly recommended to adjust the new meter before rst use, as
described in chapter 6. This will result in a higher measurement accuracy from
the beginning.
2. Functions
"This device complies with ISO standard 2178, making it equally suitable for use under
laboratory conditions as well as "in the eld" under harsh environmental conditions.
" In F mode, the thickness of non-magnetic layers, e.g. paint, plastic, enamelled
porcelain, copper, zinc, aluminium, chrome, lacquer layers, galvanised or
phosphorescent layers, alloys, etc. can be determined.
These layers should be on magnetic metals such as steel, iron, nickel etc.
"In the N- mode, the layer thickness of non-magnetic layers on non-magnetic metals.
It is used to measure anodizations, lacquer layers, glazes, colours, enamel, plastic
layers, powder coating etc. These should be on non-magnetic metals such as
aluminium, sheet metal, non-magnetic stainless steel and others.
"automatic switch-o to conserve battery power.
" Selectable units: mm, µm, inch (mil)
"The backlit display allows accurate reading
Produktspecifikationer
| Varumärke: | Sauter |
| Kategori: | Mätutrustning |
| Modell: | TB 2000-0.1F |
Behöver du hjälp?
Om du behöver hjälp med Sauter TB 2000-0.1F ställ en fråga nedan och andra användare kommer att svara dig
Mätutrustning Sauter Manualer
30 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
10 Mars 2025
10 Mars 2025
Mätutrustning Manualer
- Janitza
- Tru Components
- SOEKS
- Water-i.d.
- Comark
- Crowcon
- Lund
- Circutor
- Cocraft
- Johnson Level
- Cliff
- Vimar
- Megasat
- Carrier
- Aqua Master Tools
Nyaste Mätutrustning Manualer
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025