Schneider MTN647595 Bruksanvisning

Schneider Inte kategoriserad MTN647595

Läs gratis den bruksanvisning för Schneider MTN647595 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 9 recensioner. Har du en fråga om Schneider MTN647595 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electrical current even when the

load is switched off.

• When working on the device: Always disconnect the

device from the supply by means of the fuse in the in-

coming circuit.

• Even if the manual switch is in the „OFF“ position, a

KNX telegram can switch the connections to being

live at any time. Before working on the device, always

diconnect the fuse in the incoming circuit from the

supply.

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Always operate the product in compliance with the

specified technical data.

• Do not use the current detection function for applica-

tions relevant to safety.

• Connect only pure ohmic loads to a channel with di-

rect current (DC).

• Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

The switch actuator REG-K/4x230/16 with current

detection and manual mode (referred to below as the

actuator) can switch four loads via separate, floating

make contacts.

You can also manually switch the connected loads with

manual switches on the actuator without bus voltage.

The actuator has a bus coupler. It is installed on a

DIN-rail TH 35 according to EN 60715, with the bus

connection made via a bus connecting terminal. It is

supplied with power from the bus voltage. A data rail is

not required.

The actuator also has integrated current detection

which measures the load current of each channel.

ABus connecting terminal, max. 4 core pairs

BCable cover

CProgramming button

DProgramming LED (red LED)

EOperational LED "RUN" (green LED)

FManual switch

GScrew terminals

½CAUTION

Strong magnetic fields can influence the current

measurement. Install devices with a strong

magnetic field (e.g. wound transformers such as

bell transformers) at least 2 cm away from the

actuator.

1Set the actuator onto the DIN rail.

Getting to know the switch actuator

Connections, displays and operating

elements

Mounting the actuator

1234

LL 1 2 LL 3 4

2Connect KNX.

WARNING

Risk of fatal injury from electrical current. The

device can be damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

3Connect the bus voltage.

4Wait at least 30 seconds.

5Set the relays of the channels to the position

desired simply by switching "On/Off"

or by

changing the manual switch to "OFF".

6Connect the load.

7Connect the mains voltage.

You can now check the function of the connected load

using the manual switch, without having to load the

application from the ETS. (See the "Operating the

actuator" section.)

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

Voltage may be present at the outputs when the mains

voltage is connected to the system.

If subjected to strong vibrations during transportation,

the switch contacts might change to the enabled state.

After connecting the bus voltage, set the relays of the

channels to the position desired simply by switching

„On/Off“ or by changing the manual switch to „OFF“.

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Protect the switch contacts with a series-connected

16 A circuit breaker.

Failure to follow these instruction can result in

equipment damage.

5 mm

1 2

3 4

230 V

4 mm

KNX

16 A 16 A 16 A

L1 NL3L2

..........

SpaceLogic KNX

Switch actuator REG-K/4x230/16 with

current detection and manual mode

Operating instructions

Art. no. MTN647595

1234

LL 1 2 LL 3 4

Produktspecifikationer

Varumärke:	Schneider
Kategori:	Inte kategoriserad
Modell:	MTN647595
Färg på produkten:	Wit
Bredd:	325 mm
Djup:	325 mm
Höjd:	25.6 mm
Snäll:	Elektronische weegschaal
Typ av material (överst):	Gehard glas
Mobila operativsystem som stöds:	Android 10.0, Android 11.0, Android 12.0, Android 13.0, iOS 15, iOS 16
Blåtand:	Ja
Beeldscherm:	LCD
Skärm diagonal:	2.8 "
Wi-Fi-standarder:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Typ av strömkälla:	Batterij/Accu
Noggrannhet:	50 g
Batteri/batteritid:	1 jaar
Teknologi:	4-sensor
Maximal viktkapacitet:	200 kg
Fjärrstöd för smartphone:	Ja
Form:	Vierkant
Antal per paket:	1 stuk(s)
Säkerhetsalgoritmer som stöds:	WEP, WPA, WPA2
Måttenhet:	kg, lb
Minnesfunktion:	Ja
Kroppsfettprocent:	Ja
Andel kroppsvatten:	Ja
Pulsmätning:	Ja
BMR-bestämning (Basal Metabolic Rate):	Ja
Benmassaanalys:	Ja
Muskelmassaanalys:	Ja
Atletläge:	Ja
Viktminne:	Ja
Flera användare:	Ja
Antal användare:	8 gebruiker(s)
Minsta viktkapacitet:	5 kg
Wifi:	Ja
Batteriteknik:	Lithium-Ion (Li-Ion)
Kroppsanalys via:	Handen/voeten
Bioelektrisk impedansanalys:	Ja
Analys av visceralt fettinnehåll:	Ja