Sedona L600CART Bruksanvisning
Sedona
Inte kategoriserad
L600CART
Läs gratis den bruksanvisning för Sedona L600CART (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 3.5 stjärnor baserat på 5.5 recensioner. Har du en fråga om Sedona L600CART eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
Assembly Instructions:
SEDONA L400CART
L500CART
& L600CART
Lynx Freestanding Cart
Model L400CART, L500CART &L600CART
Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Ph
Document 33807 Rev C 02/08/13
Step 1.
Step 2.
Step 3.
Step 1.
Aer opening and idenfying the components, select the back
panel assembly and either the right or le side panel assembly.
Orient the parts as shown in the illustraon for . step 1
Note that these parts are upside down with the shelves at the
oor. Hook the right or le side to the back into the four keyways
located on the edge. When aached all four keyways should be
engaged and the back and side ush to the top.
Repeat this step for the opposite side panel.
Step 2.
With the cart oriented upside down, locate the 4 - #8 screws and
nuts and mount the electrical transformer to the access plate
shown in the illustraon for this step. It may be done at the end of
the assembly but is somewhat easier to access at this stage.
Step 3.
Refer to the gure for and insert the base assembly into the step 3
cavity at the back corners of the cabinet. Check that the tank hole
is posioned as shown and the magnet is located on the open side.
Splay the two sides out slightly and enclose them over the front of
the base. The sides and back have pockets that t over the casters
for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock
the assembly in place.
Access
Plate
magnet
tank
hole
Screw
4 places
Introducon:
Your Freestanding Cart comes with all of the components necessary
to assemble a cart for the SEDONA Series of Lynx Grills.
The SEDONA CART series is comprised of 8 sub assemblies:
1. Back Panel Assembly
2. Right Side Panel Assembly with Shelf
3. Le Side Panel Assembly with Shelf
4. Base Assembly with Wheels
5. Inner Shelf Assembly
6. Cross Brace Assembly
7. Right Door
8. Le Door
In addion there are 14 screws (1/4 -20 x ½) to assemble the
cart and grill and 4 screws with nuts (#8-32 x 3/8) to aach the
transformer assembly supplied with the Grill.
Produktspecifikationer
| Varumärke: | Sedona |
| Kategori: | Inte kategoriserad |
| Modell: | L600CART |
Behöver du hjälp?
Om du behöver hjälp med Sedona L600CART ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Sedona Manualer
27 December 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
Inte kategoriserad Manualer
- Fimer
- Tektronix
- WARN
- GPX
- Sureguard
- Peach
- ESX
- OneTouch
- Blonder Tongue
- Reginox
- Generation
- Panduit
- Molotow
- Ninebot
- Focusrite
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025