Sharp PN-ZB03H Bruksanvisning

Sharp mottagare PN-ZB03H

Läs nedan 📖 manual på svenska för Sharp PN-ZB03H (2 sidor) i kategorin mottagare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
PN-ZB03H
Operation Manual HDBaseT Receiver Board
Applicable models
(as of May 2016)
LCD MONITOR
PN-R556/PN-R496/PN-R426
Available models differ according to region.
CAN ICES-3 (A) / NMB-3 (A)
• THANK YOU FOR PURCHASING A SHARP PRODUCT.
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the
section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be
accessed at any time.
As for how to use the product, refer to the operation manual of the LCD MONITOR.
TIPS
- This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found, contact your SHARP dealer
or your nearest customer contact.
- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other
malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.
- This product and its accessories may be upgraded without advance notice.
IMPORTANT:
To aid reporting in case of loss or theft, please record the product’s model and
serial numbers in the space provided.
The numbers are located on the product.
Model No.:
Serial No.:
U.S.A. ONLY
WARNING:
FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufacturer could void the
user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
U.S.A. ONLY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take
adequate measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: USB terminal, HDBaseT terminal.
To ensure safe and correct use
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels and incorrectly using the
product could have results as classied below.
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all instructions.
Warning: Not following these instructions could result in death or serious injury.
•AskyourSHARPdealerorqualiedservicepersonfortheattachment/detachmentofthisproduct.
Attachment/detachment of this product by the customer may result in electric shock or injury.
•Nevertrytomodify,disassemble,orrepairthisproduct.
Doing so may result in re, electric shock, or injury.
•Onlyusetheaccessorieswithspeciedmodels.
Failure to do so may result in re.
CINSE1411MP51 (1)
Supplied accessories
If any component is missing, please contact your dealer.
□ HDBaseT Receiver Board: 1
□ Terminal label: 1
□ Operation manual (this manual)
□ Installation Manual (instructions for SHARP dealers and service
engineers): 1
• HDBaseT is a registered trademark of the HDBaseT Alliance.
• The terms HDMI and HDMI High-Denition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other countries.

123
1. HDBaseT

Use a commercially available LAN cable (Category 6
or better shielded cable) to connect to an HDBaseT
transmitter.
2. USB

You can connect a USB mouse or keyboard (HID class)
to this terminal to control the computer connected to the
HDBaseT transmitter.*
3. LAN

Use a commercially available LAN cable to connect to
the network. You can use this terminal in place of the
LAN terminal of the monitor.
Do not connect the LAN terminal to the same network
as the LAN that the board is connected to by way of
the HDBaseT terminal. A network loop malfunction will
occur.
*
You have to use this product with a transmitter that supports the
HDBaseT 2.0 standard. Connections to all transmitters is not guaranteed.

A commercially available HDBaseT transmitter is required to use
this board. Depending on the transmitter, some functions may not be
available. Check with the manufacturer regarding HDBaseT transmitter
specications.

• When you use this device, set the input mode to OPTION.
• In some cases, the power of the HDBaseT receiver board may remain
on even in the standby mode or input signal waiting mode. Power
consumption will be higher when this occurs.
• The power consumption of the monitor with this board attached
increases by up to 12 W.
• To use LAN signals or RS-232C signals via HDBaseT and LAN signals
that have been applied to this board’s LAN terminal, change the
CONTROL ROUTE setting under COMMUNICATION SETTING on the
SETUP menu.
You can also use control commands to change the setting.
Function Direction Reply  
Responsecontents
CONTROL
ROUTE
CTCH 0-1 0-1 0: MONITORWR
1: OPTION
○
“○” indicates a command which cannot be used in standby mode when
POWER SAVE MODE is set to ON.
*
When CONTROL ROUTE is set to OPTION, the communication speed
is xed to 9600 bps. Also, you cannot set POWER SAVE MODE to ON.
• AUTO INPUT SELECT PRIORITY is not supported.
• You can use the INFORMATION3 screen to check things such as the
communication status of the board as shown below. Set the input mode
to OPTION.
- SIGNAL STRENGTH: This displays the signal strength. The smaller
the value, the stronger the signal. To ensure stable operation, a signal
strength of at least -10 dB (-10 dB, -11 dB, -12 dB, etc.) is necessary.
- LINK STATUS: NO LINK, LINK, LOW POWER, or ETHERNET is
displayed. When LOW POWER is displayed, the link has been
established, but video cannot be transmitted. ETHERNET is displayed
when the cable that should be connected to the LAN terminal is
erroneously connected to the HDBaseT terminal.
- HDMI STATUS: NO HDMI, HDMI, or HDCP is displayed.
NO HDMI: No video data has been received.
HDMI: HDMI/DVI data without HDCP is being received.
HDCP: HDMI/DVI data with HDCP is being received.
*Set the input mode to OPTION before checking the status.
When you connect the HDBaseT Receiver Board, the following become
enabled on the monitor.
• If you are using an Extron device, set EXTRON XTP to ON under
COMMUNICATION SETTING on the SETUP menu.
• The following control commands become enabled.
Function Direction Reply  
Responsecontents
EXTRON
XTP
EXTN WR 0-1 0-1 0: OFF 1: ON ○
“○” indicates a command which cannot be used in standby mode when
POWER SAVE MODE is set to ON.

Model PN-ZB03H
Supported standard HDBaseT 2.0
 HDBaseT terminal
LAN terminal (10BASE-T/100BASE-TX)
USB terminal (USB 2.0 compliant)
Max. resolution (pixels) 4096 x 2160 (30Hz)*

distance
100 m*
Copy protection Supports HDCP (pass through)
 Supplied from the monitor
Input voltage 12 - 19 V
 12 W

 
Approx. 4-15/16(W) x 5-3/8(D) x
1-3/16(H) (124.6 x 136.5 x 30)
  Approx. 0.408(185)
*
To connect the devices, use a commercially available category 6 or
better shielded cable.
• Use this device within the operating temperature and humidity
conditions of the monitor.
As a part of our policy of continuous improvement, SHARP reserves the
right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are
nominal values of production units. There may be some deviations from
these values in individual units.
Printed in China
16G CN1

Produktspecifikationer

Varumärke: Sharp
Kategori: mottagare
Modell: PN-ZB03H

Behöver du hjälp?

Om du behöver hjälp med Sharp PN-ZB03H ställ en fråga nedan och andra användare kommer att svara dig


mottagare Sharp Manualer

Sharp

Sharp PN-ZB03H Bruksanvisning

4 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Yamaha

Yamaha Aventage RX-A4A Bruksanvisning

9 April 2025
Yamaha

Yamaha Aventage RX-A8A Bruksanvisning

9 April 2025
Phonocar

Phonocar PH544 Bruksanvisning

5 April 2025
DJI

DJI D-RTK 3 Bruksanvisning

4 April 2025
Alpine

Alpine MRX-F65 Bruksanvisning

2 April 2025
QSC

QSC SPA-Qf 60x2 Bruksanvisning

2 April 2025
Harper

Harper HDT2-5010 Bruksanvisning

2 April 2025
Harper

Harper HDT2-2010 Bruksanvisning

2 April 2025
Pro-Ject

Pro-Ject Stereo Box DS Bruksanvisning

30 Mars 2025
Streacom

Streacom TL1 Bruksanvisning

30 Mars 2025