Sharper Image Fine Facial Hair Remover Bruksanvisning

Sharper Image Inte kategoriserad Fine Facial Hair Remover

Läs gratis den bruksanvisning för Sharper Image Fine Facial Hair Remover (5 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6.5 recensioner. Har du en fråga om Sharper Image Fine Facial Hair Remover eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/5

Item No. 100871

FINE FACIAL HAIR REMOVER

User Guide

- 1 -

Thank you for choosing the Fine Facial Hair Remover from Sharper Image. Please

read this Quick Start Guide to get a general idea of how this product works. For

additional instructions and important safety information, be sure to read the

entire user’s manual in the package.

- 2 -

FEATURES

• Painless hair removal at home

• Safe for all skin tones and all hair types

• Cordless and portable

• Includes control unit, cotton buds for facial hair and eyebrows

• Includes pad set (3 rectangular pad, 2 round pads and 1 upper lip pad) for treating

larger areas

• Includes 1 lead with 3 pad connectors

• Includes treatment tweezers and curly lead for removing single hairs

• Includes conductive gel and carry case

• Operates on 2 included AA batteries

IDENTIFICATION OF PARTS

BATTERY INSTALLATION

• Install the 2 AA batteries (included) by pressing the battery cap down.

• Insert the batteries according to the correct polarity (“+” or “-”).

• Replace the cap.

- 3 -

HOW TO USE COTTON BUD TO REMOVE HAIR WITH THE FINE FACIAL

HAIR REMOVER

1. Thoroughly clean treatment area by removing all makeup. The area must

be completely clean, dry and non-greasy.

2. Cut the cotton bud in half and insert into the tip of the device.

3. Dip cotton bud into the conductive gel making sure the gel also covers

the cotton bud holder at the tip of the control unit.

4. Hold the Fine Facial Hair Remover like a pen and slide the switch to the

PROBE position. (Red power light should illuminate to conﬁrm battery is

working). See illustrations on Page 5 for proper holding technique.

5. Put the device on the hair removal area and press the silver activator

button. The green LED light will come on when you’ve made good contact

with the conductive gel, and a buzzer will go oﬀ after 20 seconds to

notify you that the treatment is ﬁnished.

Note: If you do not touch the gel continuously, the green conductivity

light will go out. Do not exceed one 20-second treatment per day in the

same treatment area (2-cm diameter). Do not exceed a maximum of 3

treatments per week in one treatment area.

Note: To avoid shock do not hold the silver activator button down after the

green conductivity LED light illuminates.

HOW TO USE TREATMENT TWEEZERS WITH THE FINE FACIAL HAIR

REMOVER

1. Thoroughly clean treatment area and remove any makeup. The area

must be completely clean, dry and non-greasy. Cut long hairs as short as

possible with scissors or a razor before use.

2. Plug the Treatment Tweezers into the jack on the end of the Fine Facial

Hair Remover.

3. Apply conductive gel to the target area and to the tweezer tips.

4. Slide the switch to mode.PROBE

5. Select and hold hair to be treated between tweezer tips. When tweezers

are squeezed together the green conductivity LED light will illuminate

and beep.

6. Gently remove hair in the direction of growth on the upper lip and face,

eyebrows or chin using the tweezers.

Produktspecifikationer

Varumärke:	Sharper Image
Kategori:	Inte kategoriserad
Modell:	Fine Facial Hair Remover
Färg på produkten:	Black, Yellow
Vikt:	645 g
Bredd:	136 mm
Djup:	153 mm
Höjd:	85 mm
Snäll:	Koeler
Användarmanual:	Ja
Ljudnivå (låg hastighet):	4 dB
Ljudnivå (hög hastighet:	24.9 dB
Typ av förpackning:	Doos
Minsta luftflöde:	16.6 cfm
Maximalt luftflöde:	51.17 cfm
Antal fans:	1 ventilator(en)
Färg på belysningen:	Blue, Green, Red
Rotationshastighet (max):	1200 RPM
Rotationshastighet (min):	300 RPM
Belysning LED:	Ja
Lämplig plats:	Processor
Kompatibla processorer:	AMD A, Intel Atom, Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Pentium
Harmoniserad systemkod (HS):	84733080
Grundläggande plåtmaterial:	Koper
Ventilator diameter:	120 mm
Spänningsklassificering:	12 V
Nominell nätspänning:	0.13 A
Maximalt lufttryck:	1.5 mmH2O
Stöd för pulsbreddsmodulering:	Ja
Typ av lager:	Sealed Precision FDB
Matventilator (bxdxh):	120 x 120 x 27 mm
Minsta lufttryck:	0.076 mmH2O
Från Koelpa:	Ja