Shure MX395 Bruksanvisning
Läs gratis den bruksanvisning för Shure MX395 (9 sidor) i kategorin mikrofon. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 4 recensioner. Har du en fråga om Shure MX395 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/9
1/9
MX395 -- Low-Profile Boundary Microphone
General Description
Shure MX395 low-profile microphones are for use in boardrooms and other sites where aesthetics are important.
The MX395 is only 2.5 cm (1 in.) in diameter, and extends just 2 cm above the mounting surface when installed.
Despite its small size, the MX395 delivers clear, high quality sound.
Features
•Low profile, aesthetic design
•Wide dynamic range and smooth frequency response
•RF filtering with CommShield technology
•Available with logic-controlled bi-color status indicator
Model Variations
The MX395 is available in cardioid, omnidirectional, and bidirectional polar patterns, with or without an LED status
indicator, with a black, white, or aluminum finish.
Polar Patterns
The polar pattern is indicated by the molded grille.
Microphone Placement
For best low-frequency response and rejection of background noise, place the microphone on a large, flat surface,
such as a floor, table, or lectern.
To reduce reverberance, avoid reflective surfaces above or to the side of the microphone, such as beveled sides
of pulpits or overhanging shelves.
®
®
Shure Incorporated
2/9
DIP Switches
Set DIP Switch 1 up to engage the low cut filter, which attenuates frequencies by 6 dB per octave below 150 Hz.
Switch Down (default) Up
1 Full frequency response Low cut filter
2 -- --
Installation
Install the microphone into a tabletop as shown.
Important:
•Align indentation toward talker
Shure Incorporated
3/9
•Do not over tighten the wing nut, as this reduces shock isolation
LED Logic
For models equipped with an LED, use the included 5-pin XLR connector to wire the microphone to an automatic
mixer or other logic device.
Note: Connect the LED IN to the gate output to illuminate the LED when the channel is gated on.
Do not use the relay ports on Crestron and AMX devices. Use the I/O logic ports instead.
The LED logic may not function when connecting to devices that do not have internal "pull-up resistor" logic cir-
cuits, such as ClearOne DSP products. External pull-up resistor circuits can be added for each microphone. Vistit
www.shure.com/FAQ for detailed instructions.
Logic Connection
Connection to device with internal "pull-up resistor" logic circuit
Produktspecifikationer
| Varumärke: | Shure |
| Kategori: | mikrofon |
| Modell: | MX395 |
Behöver du hjälp?
Om du behöver hjälp med Shure MX395 ställ en fråga nedan och andra användare kommer att svara dig
mikrofon Shure Manualer
30 December 2025
30 December 2025
30 December 2025
30 December 2025
30 December 2025
30 December 2025
26 Oktober 2024
25 September 2024
23 September 2024
22 September 2024
mikrofon Manualer
- JLab
- NGS
- Samson
- Sound Devices
- Sonuus
- Electro-Voice
- Rolls
- Hama
- PureLink
- Chord
- Fenton
- Aston Microphones
- Aluratek
- Polsen
- Lenco
Nyaste mikrofon Manualer
17 Juni 2025
16 Juni 2025
16 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025