SIIG LB-GE0114-S1 Bruksanvisning
SIIG
Nätverkskort/adapter
LB-GE0114-S1
Läs gratis den bruksanvisning för SIIG LB-GE0114-S1 (4 sidor) i kategorin Nätverkskort/adapter. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 11 recensioner. Har du en fråga om SIIG LB-GE0114-S1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
1
04-1056A
Gigabit Ethernet PCIe
4-Lane Card
Introduction
The Gigabit Ethernet PCIe 4-Lane Card adds Gigabit
Ethernet ports to your PCIe-enabled server or
desktop systems.
Specifications
• Bus connector: PCI Express x4
• Version: PCI Express 2.1
• Network transfer rate: 10/100/1000 Mbps
System Requirements
• Desktop PC with one available PCIe slot
• Windows
®
10 (32-/64-bit) / 8.x (32-/64-
bit) / 7 (32-/64-bit)
• Windows Server 2012 R2 / 2012 (32-/64-
bit) / 2008 R2 / 2008 & 2003 (32-/64-bit)
Installation Guide
2
Package Contents
• Gigabit Ethernet PCIe 4-Lane Card
• Low profile bracket
• Driver CD
• Installation guide
Hardware Installation
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
Note: For slim desktop PCs, replace the pre-
installed bracket by the included low profile
bracket.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord from the computer.
3. Remove your computer cover.
4. Remove the slot bracket from an available
PCIe slot.
3
5. Carefully align the card's bus connector
with the selected PCI Express slot on the
motherboard. Push the card down firmly,
but gently, until it is well seated.
6. Replace the slot bracket holding screw to
secure the card.
7. Replace the computer cover and reconnect
the power cord.
Windows Driver Installation
Windows 10 and 8.x have built-in driver support
for this adapter. Just install the board and
Windows will automatically detect and install
the correct drivers for it. No additional driver is
needed.
For earlier versions, follow below instructions to
install the driver:
1. After Hardware Installation, start the
computer and insert the driver CD.
2. The AutoPlay window will show
automatically, and select RUN
AUTORUN.EXE. If not, browse the CD
manually.
Produktspecifikationer
| Varumärke: | SIIG |
| Kategori: | Nätverkskort/adapter |
| Modell: | LB-GE0114-S1 |
Behöver du hjälp?
Om du behöver hjälp med SIIG LB-GE0114-S1 ställ en fråga nedan och andra användare kommer att svara dig
Nätverkskort/adapter SIIG Manualer
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
20 September 2024
Nätverkskort/adapter Manualer
- Ernitec
- Riello
- Emtec
- SEH
- Logilink
- Tripp Lite
- Grixx
- Vivotek
- IDIS
- Advantech
- TP Link
- Xcellon
- Sennheiser
- Panamax
- Allnet
Nyaste Nätverkskort/adapter Manualer
8 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
1 April 2025
30 Mars 2025
29 Mars 2025
14 Mars 2025
14 Mars 2025