Soma Illuminator Bruksanvisning

Soma Inte kategoriserad Illuminator

Läs gratis den bruksanvisning för Soma Illuminator (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 11.5 recensioner. Har du en fråga om Soma Illuminator eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
Cut your LED strips and wires into their
desired lengths and connect them to-
gether and to the DC sockets supplied
with ILLUMINATOR.
• LEDstripshavespecialplaceswhere
you can cut the strip, usually they are
copper pads like in the photo below.
It’s important to cut the strip on the
middle line of these copper pads
3
.
• Youcansolderthewireeitherdirectly
to the copper pads or using ashort
wire that is often soldered to one or
both ends of the LED strip by the fac-
tory. Before soldering to the copper
padsyouneedremovethesiliconlayer
(ifpresent)coveringthepadsusing
asharp knife.
• Beawareofpolarity!Theplusand
minus on the LED strips are usually
marked by +
signs. The plus wire on
the speaker cable is usually marked by
aspecial color or line on one of the
wires. It doesn’t really matter which
of the two wires on the cable you use
for plus and minus. What matters is
that the plus of the LED strip is
connected to the central pin on
the DC jack. But don‘t worry. If you
mix up the polarity of the strip nothing
will be damaged, the strip just won’t
lightup.Inthiscasejusttrytoreverse
the polarity.
• Theconnectionbetweenthestripand
thewireshouldbecoveredinseveral
layers of isolation/electrical tape or
heatshrinktubing.Thisservestoboth
isolatetheconnectionandtogiveit
additional mechanical strength. In case
ofexcessivestress,thisistheplace
where the wire will likely be ripped from
the strip.
The strips are ready for use when all
of them are soldered to the wires, the
wires are soldered to the DC jacks and
all connections are insulated.
Now you need to choose aproper power
supply.YoucanbuyahighqualityPSU
from us (atan additional price) or use
aPSUthatyoualreadyhave.The PSU
must be 12V and the output DC jack
needs to be center plus. To calculate
the current your LED strips will need,
use the simple formula:
PSU max current in Ais equal or
more than total length of all LED
strips in meters x 0.3.
If your LED installation is not big, a1–2A
PSUcanbeenough.
If you use amodern switching mode
PSUyoudontneedtoworryabout
overload.Allofthemhaveoverload
protection and will be shut down au-
tomaticallyiftheloadistoobig.Sono
ILLUMINATOR comes without LED strips,
wiresorPSU.Thereasonissimple
we
don‘t know what colors and length of
strips you need as well as what length
ofcables.Eachinstallationisveryper-
sonal and we can‘t supply something
thatcouldbecalled„auniversalsolu-
tion“.Youneedtoconnectthestrips
yourselfwhichrequiresbasicsoldering
skillsaswellassimplesolderingequip-
ment. Therefore, using ILLUMINATOR
requires some basic technical skills
and understanding.
First of all you need to buy LED strips
of desired length and color. You need
12V LED strips
1
.
Typically, one meter (3 feet) of aLED
strip consumes 0.2–0.35 ampere. We
recommend limiting the total length
of all LED strips connected to ILLU-
MINATOR to amaximum of 16 meters
(52 feet). Different strips connected to
differentchannelscanhavedifferent
lengths.
Secondly, you need to buy wire for
connecting LED strips to ILLUMINATOR.
We recommend standard speaker wire
used for audio speakers
2
. Its import-
ant that the copper core is at least 0.35
squaremillimeters.0.51squaremilli-
meters is the optimal thickness.
OPERATION
MANUAL
1 2 3


Produktspecifikationer

Varumärke: Soma
Kategori: Inte kategoriserad
Modell: Illuminator

Behöver du hjälp?

Om du behöver hjälp med Soma Illuminator ställ en fråga nedan och andra användare kommer att svara dig