Sonic Alert HA360SSBC Bruksanvisning
Sonic Alert
Säkerhet
HA360SSBC
Läs gratis den bruksanvisning för Sonic Alert HA360SSBC (2 sidor) i kategorin Säkerhet. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 12 recensioner. Har du en fråga om Sonic Alert HA360SSBC eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
INSTALLATION AND SET UP FOR HOMEAWARE™ TRANSMITTER
HA360SSBC – Baby Cry
The HomeAware™ HA360SSBC transmitter is
designed to alert you to the sound of a baby crying.
This transmitter alerts you through the HomeAware™
Main unit and remote receivers located in other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See
diagram for battery door location. Battery backup will
provide power when a power outage has occurred.
Power will be provided for a continuous outage lasting
7 days, or for short outages up to two years.
Link Button Set Up
This procedure will link the HA360SSBC – Baby Cry to
your Main unit. The Main unit will also provide an alert
to all HomeAware™ remote receivers. When using the
Bridge unit HA360BU all original Sonic Alert receivers
(SA101, SA201, BL300, and SB1000) will also alert
you.
It is best to do the link procedure in the same room with
the HomeAware™ Main unit, make sure the unit is
plugged in.
To link a transmitter to your HomeAware™ Main
unit:
1. Press set up button and the word LINK will be
shown on the display, press Enter. LINK will begin
blinking. (If LINK mode is entered by accident,
simply press the BACK button to exit and return to
the clock.)
2. Press and hold down the Link button on the back of
your transmitter for about 1 second. The red LED
on the transmitter will light up. Release the button.
3. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAware™ main unit will briefly show DONE,
and return to the time display. Your transmitter is
now connected and ready to test and use.
Sensitivity Switch
You can adjust the sensitivity of the Baby Cry detector.
There are three levels to choose from: The HI setting is
the most sensitive setting and will alert you to more
sounds. Moving this switch to MED makes it less
sensitive and will alert you to less sound. The LO
setting is the least sensitive. If you are not picking up
the sound you need to be alerted to, simply move the
sensitivity switch to a higher setting. If you have set this
setting to HI and you are still not picking up the sound
try moving the transmitter closer to the sound.
When a sound is detected it will send a signal to the
HomeAware™ base unit and all HomeAware™ remote
receivers, also the red LED light will flash on the front
of the unit.
Low Voltage Input
HomeAware™ transmitters have a low 120 volt AC
power supply that powers the HA360ss. Simply plug
the unit into any 120 volt AC power outlet. Next plug
the other end into the Low Voltage Input located on the
side, see diagram below.
FCC Requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions; (1)
This device might not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Produktspecifikationer
| Varumärke: | Sonic Alert |
| Kategori: | Säkerhet |
| Modell: | HA360SSBC |
Behöver du hjälp?
Om du behöver hjälp med Sonic Alert HA360SSBC ställ en fråga nedan och andra användare kommer att svara dig
Säkerhet Sonic Alert Manualer
12 September 2024
10 September 2024
10 September 2024
10 September 2024
6 September 2024
6 September 2024
5 September 2024
31 Augusti 2024
29 Augusti 2024
29 Augusti 2024
Säkerhet Manualer
- Medion
- Edimax
- Trendnet
- I-Tel
- Elro-Flamingo
- Smartalarm
- Entrya
- Brennenstuhl
- Golmar
- Hagenuk
- Airbolt
- Unitron
- ME
- Switel
- Paradox
Nyaste Säkerhet Manualer
19 Februari 2025
12 Januari 2025
7 Januari 2025
7 Januari 2025
24 Oktober 2024
22 Oktober 2024
21 Oktober 2024
20 Oktober 2024
20 Oktober 2024
Axis Camera Station S9001 Mk II Desktop Terminal Bruksanvisning
19 Oktober 2024