Sony RM-V302T Bruksanvisning

Läs gratis den bruksanvisning för Sony RM-V302T (3 sidor) i kategorin Fjärrkontroll. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.1 stjärnor baserat på 7 recensioner. Har du en fråga om Sony RM-V302T eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Notes on Batteries

•Do not mix old batteries with new ones or mix different types of

batteries together.

•If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow steps 1 and 2 below for each component you plan to use with

the Commander.

Step 1: Entering the Code Number

1See the supplied “Component Code numbers” table, and find the

three-digit code number for the desired component.

If more than one code number is listed, use the number that is

listed first to complete the steps below.

For example, if you are setting up a Philips TV, you would use the

code number 086.

If your component is not listed, see “Searching for the Correct

Code.”

2While pressing the S (SET) button, press

the 1 button.

3Press the button of the component that

you want to set up.

Note

On the , and buttons, “VCR,” “satelliteVCR SAT AMP, , DVD

tuner,” “amplifier,” and “DVD player” are assigned respectively

at the factory. But you can also assign other components on these

buttons. For details, see “Changing the Component Type on the

VCRSATAMPDVD , , , and buttons.”

4Enter the component’s code number.

For example, if you are entering the code

for a Philips TV, you would press

-86.

5Press and release the t button to store

the code number in the Commander’s

memory.

6Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

If you press a wrong button in step 4

Press the button while pressing the button and then go1S (SET)

back to step 2.

Changing the Factory Setting for the

Volume Control

1While pressing the button, press the S (SET) 1button.

2Press the AMP button.

3Press the 2+ button.

4Press the t button.

The volume control setting is changed to “amplifier.” You can

control the volume of the amplifier of the button whileAMP

selecting any component.

Notes

•If you are using more than one amplifier and have set it on the

VCRSAT DVD , or button, when selecting these buttons you cannot

control the volume of the amplifier of the AMP button.

•If you change the setting of the AMP button to a component other

than a receiver or amplifier, the volume control setting of video

components will return to “TV” even if you have changed the

factory preset volume control. In this case, you will not be able to

control the volume from audio components other than a receiver or

amplifier.

To reset to factory preset volume control

In step 3 above, press 2– instead.

Operating a Component

1Press the button of the desired

component on the Commander.

2Point the Commander directly at the

component.

3Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

•Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a function, the button on thisMUTING %

Commander will not function with your TV.

•Some functions of the component may not work with this

Commander.

Setting a channel with a single button

(Channel Macro function)

You can program the function on any of the buttonsChannel Macro

listed below (macro keys).

For example, instead of pressing , , and then button to1 2ENT

change the TV channel, you can perform these operations by

pressing only the N

button.

The macro keys are:

N m M xXz, , , , , and REC.

(During “TV“ or “satellite tuner“ operations only.)

The series of operations that can be programmed must consist of two

to four sequential pressings of the buttons or - to 9ENTbutton.

Note

The Channel Macrofunction may not work correctly for some

components.

Setting Up the Remote Commander

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you are using the Commander with a Sony component, you will

not need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you will need to follow the instructions in this

manual to preset the Commander with the correct code number for

your component(s). (See the supplied “Component Code Numbers”

table also.)

Notes

•The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

•You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

Installing the Batteries

Before replacing the batteries, have new ones ready

beforehand.

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

1 2

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

•Replace both batteries with new ones.

•Do not take more than 3 minutes to replace the batteries; otherwise,

your code number settings will be erased.

Remote Button Descriptions

Step 2: Checking if the Code Number Works

1Turn on the component you want to set up.

2Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the button to see if it works on your1

component.

3Check that the other buttons of the Commander are operating the

corresponding functions of the component.

You can write down the code number on the label inside the

battery compartment lid.

If the Commander Does not Seem to be Working...

•First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers” table).

•If after trying all the codes listed for your component you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Searching for the Correct Code

If you have tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” table), try these steps.

Before starting the Search function

Set each component to the following status to enable the Search

function.

TV, AMP: power-on

CD, MD, TAPE, DAT: power-on with a playback source (disc,

cassette tape, etc.)

Other components: power-off

1While pressing the button, press the S (SET) 1button.

2On the Commander, press the button of the component that you

want to set up.

3Press and release the PROGR+ button. Then press and release the

1 button.

4Repeat step 3 until the correct code number is found.

Each time you press the button and then the button, aPROGR+ 1

new code number will be transmitted.

Keep trying until your component operates as follows:

•TV, AMP: power-off

•CD, MD, TAPE, DAT: power-off or playback

•Other components: power-on

•TV without a power switch: the Channel + function works.

Be patient as you do this; it could take as many as 120 tries before

the correct code number is located.

5When the correct code is found, press the t button to store the

code number in the Commander’s memory.

6Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you are done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 5 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Note

Be sure to proceed to each next step in the above procedure within

10 seconds; otherwise setting mode will be canceled.

Changing the Component Type on the VCR,

SAT, AMP, and DVD buttons

At the factory, “VCR” is assigned to the button, “satellite tuner”VCR

to the button, “amplifier” to the SATAMP button and “DVD player”

to the button. By completing the following procedure, you canDVD

change this setting so that you can assign any component to these

buttons.

1While pressing the button, press the S (SET) 1button.

2Press the VCR SAT AMPDVD, , , or button.

3Press and release the x (stop) button.

4Press and release one of the following buttons:

1 to assign a VCR

3 to assign a satellite tuner

4 to assign an amplifier

5 to assign a CD

6 to assign a tape deck

7 to assign an MD deck or a DAT deck

8 to assign a TV

- to assign a DVD

5Press and release the t button.

6Enter the component’s code number by following steps 2 to 6 of

“Entering the Code Number,” or steps 1 to 6 of “Searching for the

Correct Code.”

Controlling the Volume of Video

Components Connected to an Audio

System

The Commander is factory preset based on the assumption that you

hear the sound of your video components from your TV’s speakers,

and that you hear the sound of your audio components from the

loudspeakers connected to your amplifier (or receiver).

Factory Setting:

*If you assign an audio component on the VCRSAT DVD , or button, you can

control the volume of the amplifier on the button. If you assign videoAMP

components on these buttons, you can control the volume of the TV.

Thus you can control the volume of your TV or amplifier while

operating a video or audio component without first having to press

the or TV AMP button. For example, to control the volume for your

VCR channels, you do not need to press the button first.TV

However, if your video components are connected to an audio

system, you probably hear your TV’s or VCR’s sound from the

loudspeakers connected to your amplifier (or receiver), not from

your TV speakers. In this case, you need to change the factory setting

so that you can control the volume of your video components

without first having to switch to the amplifier (or receiver).

To change the factory setting for the volume control, follow the

procedures below.

Note

This feature is effective only when an amplifier (or receiver) is set up

on the button. You cannot control the volume of an amplifierAMP

(or receiver) set up on button while operating theVCRSAT DVD , or

component of another button.

Button

TV

VCR, SAT, DVD* *

AMP

Controls the volume of

TV

TV

Amplifier

Operating a tape deck

English

3-264-084- (1)11

Remote CommanderRM-V302T

Operating Instructions

Mode d’emploi (au verso)

© 2004 Sony Corporation Printed in China

General

1To set up the Commander,

press .S (SET) while pressing 1

52+:Volume up.*1

2–:Volume down.

7To mute the volume on the TV

or amplifier.*1

qaTo turn on and off the power of

the selected component.

qsComponent select buttons. To

switch to the operations of each

component, press the button on

which that component is

assigned.

*1These buttons control the volume of

either TV or amplifier. See

“Controlling the Volume of Video

Components Connected to an

Audio System” for details.

3 q; qlw;, , and

Tape operation buttons.

For dual cassette decks,

operation buttons for Deck A

(for Sony-brand dual cassette

deck, buttons for Deck B).

-:To reverse.

N:To play.

m:To rewind.

M:To fast-forward.

zREC:To record, press N

while pressing zREC.

First release , thenN

release .zREC

x:To stop.

X:To pause.

8 9 qdqk, , and

Operation buttons for Deck B

(for Sony-brand dual cassette

deck, buttons for Deck A).

Specifications

Operable distanceApprox. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirementsTwo size AA (R6) batteries (not supplied)

Battery lifeApprox. 6 months (varies depending on frequency of

use)

DimensionsApprox. 55 × 200 × 32 mm (w/h/d)

(2 1/ 4× 7 7/ 8× 1 5/16 in.)

MassApprox. 95 g (3.4 oz.) (not including batteries)

Design and specifications are subject to change without notice.

The validity of the CE marking is restricted to only those countries where it is

legally enforced, mainly in the countries EEA (European Economic Area).

S

TV

DVDAMP

VCRSAT

1

4 5 6

7 8

0ENT

2-1-

PROGR

DVD

TVMD

CDTUNERTAPE

VIDEO 2

PHONO

S

GUIDEMENU

REC

OK

9

VIDEO 1AUX

2 3

TV

DVDA MP

VCRSAT

ENT:To reverse.

:To play.

:To rewind.

:To fast-forward.

:To stop.

MENU:

To record, press

while pressing MENU.

First release , and

then release MENU.

OK:To pause.

qhTo select Deck A or Deck B

(dual cassette deck only).

If your tape deck’s commander has

one set of tape operating buttons, and

has an A/B button for the deck

selection, use the button to select

Deck A or Deck B.

To program a series of operations

1Press the desired component select button.

(You can select “TV” or “satellite tuner” only.)

2While pressing the desired macro key, press the buttons required

for the operations in sequence.

For example, to program 1t 2tENT on the N button, hold

down , N first, press 1 2, and ENT in sequence, and then release

N.

Notes

•Even if you try to program more than four operations and press the

corresponding buttons in step 2 above, only the first four buttons

that were pressed will be programmed.

•If you try to program only one operation on a macro key, the

setting operation will be rejected.

•You can program the function for up to threeChannel Macro

components only. To program a fourth component, first clear all

macro keys for a component.

•If you have programmed the function for TV orChannel Macro

satellite tuner operation, the button used as a macro key cannot be

used for Fastext buttons.

To change or clear a program

When you want to change the setting, or if you are no longer using a

programmed operation, follow the procedure below to overwrite or

clear the program.

1Hold down the macro key that you want to change or clear.

2After waiting for about three seconds, press the new sequence of

buttons, or, to clear the program, press and release , and then-

press and release ENT.

3Release the macro key.

Note

Be sure to wait for about three seconds in step 2 above. While you

are holding down the macro key and waiting, the programmed

signals are transmitted; therefore, if you are aiming the Commander

at your component, the programmed operations may be performed

before you go on with the procedure.

Troubleshooting

If you have problems setting up or using the Commander:

• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.” If the code that is listed first for your

component does not work, try other codes for that component in the order in

which they are listed. If all the codes fail to work (or if your component is not

listed in this manual), try using the procedures in “Searching for the Correct

Code.”

• Check that you are aiming the Commander directly at the component, and

that there are no obstructions between the Commander and the component.

• Make sure the batteries you are using are not worn out, and that they are

inserted correctly.

• , , , Check that the button of the TV VCR SATAMP or DVD is pressed to choose

your desired component.

• Check that the component has infrared remote capability. For example, if

your component did not come with a remote commander, it is probably not

capable of being controlled by a remote commander.

• If your video components are connected to an audio system, make sure you

have set up the Commander as described in “Controlling the Volume of

Video Components Connected to an Audio System.”

• Should any problem persist, reset the Commander to the factory setting by

pressing the 1 2, t and – buttons simultaneously.

Customer Service

If you have any questions or problems concerning the

Remote Commander that are not covered in this

manual, please call the customer remote helpline. The

number is mentioned in the warranty card.

Operating a TV

2To change the programme.

Also to turn on the power.

3To select double-digit numbers.

Works in the same way as your

TV’s commander.

4To change the input mode.

6To switch to Teletext.

8To move the cursor upward,

downward, to the right or left.

9To call up the MENU display.

qdTo select a number between 20

and 29.

qfPROGR+:

Programme up.

PROGR–:

Programme down.

qgTo turn on.

To return from Teletext to TV.

qhTo operate JUMP,

FLASHBACK, or CHANNEL

on the TV, depending on the

manufacturer’s setting.

qkTo enter the selection.

qlFastext buttons.

Operating a VCR

2To change the programme.

3To select double-digit numbers.

Works in the same way as your

VCR’s commander.

4To switch the signals supplied

to the TV.

6To expose the on-screen

display.

8To move the cursor upward,

downward, to the left, or to the

right.

9To call up the MENU display.

q; qlw;, and

N:To play.

x:To stop.

m:To rewind.

M:To fast-forward.

zREC:To record, press N

while pressing zREC.

X:To pause.

qdTo select a number between 20

and 29.

qfPROGR+:

Programme up.

PROGR–:

Programme down.

qgTo change the input mode.

qkTo enter the selection.

Operating a DAT deck

2To select the track number.

3To select numbers 10 and

above.

6To change the display mode or

turn the display on/off.

q;To record, press N while

pressing .zREC

First release , then releaseN

zREC.

qfPROGR+:

To select the next track.

PROGR–:

To select the previous

track.

ql N:To play.

m:To rewind.

M:To fast-forward.

x:To stop.

w; X:To pause.

Operating a CD

2To select the track number.

3To select numbers 10 and

above.

4To switch the input source.

6To turn the display of the CD

player on/off.

q;To record, press Nwhile

pressing .zREC

First release , then releaseN

zREC.

qdTo enter a setting.

qfPROGR+:

To select the next track.

PROGR–:

To select the previous

track.

qgTo clear a setting.

qhTo select the next disc.

qjTo select player or recorder.

ql N:To play.

m:To rewind.

M:To fast-forward.

x:To stop.

w; X:To pause.

Operating an MD deck

2To select the track number.

3To select numbers 10 and

above.

6To change the display mode or

turn the display on/off.

q;To record, press N while

pressing .zREC

First release , then releaseN

zREC.

qdTo enter the setting.

qfPROGR+:

To select the next track.

PROGR–:

To select the previous

track.

qgTo clear a setting.

qhTo select the next disc.

ql N:To play.

m:To rewind.

M:To fast-forward.

x:To stop.

w; X:To pause.

Operating a satellite tuner

2To change the programme.

3To select double-digit numbers.

Work in the same way as your

satellite tuner’s commander.

4To change the input mode

(H/V).

8To move the cursor upward,

downward, to the right or left.

9To call up the MENU display.

qdTo select a number between 20

and 29.

qfPROGR+:

Programme up.

PROGR–:

Programme down.

qhTo operate JUMP,

FLASHBACK or CHANNEL

RETURN function on the

satellite tuner, depending on

the manufacturer’s setting.

qjTo bring up the Master Guide.

qkTo enter the selection.

qlFastext buttons.

Operating an amplifier (or receiver)

2To select the input source:

1 selects VIDEO 1

2 selects VIDEO 2

3 selects AUX

4 selects TUNER

5 selects CD

6 selects TAPE

7 selects MD

8 selects TV

9 selects PHONO

- selects DVD

4To switch the input source by

each press.

qfPROGR+:

Presetting frequency up.

Tuning frequency up.

PROGR–:

Presetting frequency

down.

Tuning frequency down.

qhTo change bands (FM/AM).

TV

DVDAMP

VCRSAT

Operating a DVD

2Number buttons: To set items

selected from the screen.

3To select numbers 10 and

above.

4To change the sound.

6To show the current play status

on the screen.

8To move the cursor upward,

downward, to the left, or to the

right.

9To display the DVD menu.

q;To record, press Nwhile

pressing .zREC

First release , then releaseN

zREC.

qdTo enter the setting. To set

items selected from the screen.

qfPROGR+:

To proceed to the next

location or song.

Programme up.

PROGR–:

To proceed to the

previous location or

song.

Programme down.

qgTo switch the subtitle.

qhTo display the title menu.

qjTo clear the selected characters

from the screen.

To select the deck.

qkTo execute items selected from

the screen.

ql N:To play.

m:To rewind.

M:To fast-forward.

x:To stop.

w; X:To pause.

Your Code Number

086

Component that can be preset

TV

VCR/Satellite tuner/Amplifier (or

receiver)/CD/Tape deck/

MD deck/DAT deck/DVD/TV

Button

TV

VCR

SAT

DVD

AMP

Factory setting

Sony TV

Sony VHS VCR (VTR3)

Sony satellite tuner

Sony DVD player

Sony amplifier

Helpline available

zThe number 5 button and the

PROGR+ button each have a

tactile dot for ease of use.

Produktspecifikationer