Spectron SP 112 Bruksanvisning
Läs gratis den bruksanvisning för Spectron SP 112 (2 sidor) i kategorin bilradio. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 12 recensioner. Har du en fråga om Spectron SP 112 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
SPECTRON BANDPASS SUBWOOFER
Congratulations on your purchase of this SPECTRON bandpass
subwoofer system.
Read and follow the operating and adjustment instructions for
this trunk box subwoofer model given below carefully, to
obtain best possible sound quality and performance from this
product.
KEY FEATURES
ILOADED WITH SPECTRON SP-S10/12 WOOFER
ILARGE CROSS SECTION SLOT PORT FOR HIGH SPL
ICHROMED WOOFER GRILLE WITH BICOLOR
LED ILLUMINATON
IMDF CABINET WITH INTERNAL BRACING
ISPACE SAVING SLOPED REAR WALL DESIGN
ICURVED ACRYLIC WINDOW FOR LOW FLEX
ISPRING-LOADED TERMINAL
For safety and legal reasons, it might be prohibited using the box illumination while operating a car. Restrictions may apply
in certain countries. For making sure to follow all national traffic and vehicle regulations and not to distract drivers attention,
we recommend connecting the box illumination to the interior light of the trunk.
TECHNICAL SPECIFICATIONS
Model: SP-110BP SP112BP
Enclosure type: 10” Bandpass Subwoofer 12” Bandpass Subwoofer
Frequency response: 30 Hz – 120 Hz 25 Hz – 120 Hz
Nominal impedance: 4 ohms 4 ohms
Sensitivity 1W/1m: 90 dB 92 dB
Maximum power handling: 400 W 500 W
Dimensions WxHxD: 425 x 310 x 225/390 mm 485 x 375 x 235/435 mm
PLACEMENT OF BOX
This SPECTRON bandpass model is designed and engineered to be placed in the trunk of the car, to achieve full bass
perfomance and low end extension.
POWER CONNECTION FOR LED ILLUMINATION
Connect the 3.5mm plug with the extension wire to the receptor inside the terminal. Connect the loose ends to an appropriate
switched 12V source like the trunk box illumination, if you intend to use the illumination feature of this product.
AUDIO CONNECTION AND SETTINGS
Before any adjustments are attempted, “treble“, “bass“ and “loudness“ controls of the head-unit must be set to their neutral/zero
position. Your bandpass subwoofer needs a low-pass filtered signal with at least 12dB/oct. slopes for best results.
§Activate the lowpass function of the amp channel(s) driving your bass box.
§Set the lowpass crossover frequency of the channel(s) driving the sub to approx. 80 Hz
§Connect the speaker wire of your sub amp to the speaker terminal on the backside of the sub.
§Increase the input gain of the subwoofer channel, until bass output is loud enough.
„In-phase“ connection of your subwoofer is critical – if your sub plays out of phase, the output at the crossover frequency region
will be depressed due to cancellation effects.
Thus one connection polarity of your sub will give you a „fatter“ and more dynamic bass reproduction in the 80Hz range.
That’s the one to go for.
manual SP-110BP_112BP:manual spectron 012W + WX 28.02.2008 15:06 Uhr Seite 1
Produktspecifikationer
| Varumärke: | Spectron |
| Kategori: | bilradio |
| Modell: | SP 112 |
Behöver du hjälp?
Om du behöver hjälp med Spectron SP 112 ställ en fråga nedan och andra användare kommer att svara dig
bilradio Spectron Manualer
10 September 2024
1 September 2024
26 Augusti 2024
bilradio Manualer
- Medion
- Voxx
- Auna
- Stinger
- Ground Zero
- Smart
- Multilaser
- Becker
- Pyle
- SPC
- ECG
- Varta
- McIntosh
- MB Quart
- Xomax
Nyaste bilradio Manualer
18 Oktober 2025
16 Oktober 2025
14 Oktober 2025
13 Oktober 2025
12 Oktober 2025
11 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025