StarTech.com M2E1BRU31C Bruksanvisning
Sidor 2 Engels Extern hårddisk
Läs bruksanvisningen för StarTech.com M2E1BRU31C gratis online eller ladda ner PDF:en. 34 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: December 18, 2019 6:37 PM
Product Diagram (M2E1BRU31C)
Exterior
ComponentFunction
1Power LED
• Solid: Indicates that the Enclosure is receiving
power.
• Flashing: Indicates that the Drive activity.
2USB-C Port
• Used to connect the Enclosure to the Host
Computer.
Interior
ComponentFunction
3Drive-Bay Screws x 4
• Used to secure the Drive Bay Cover in the
Enclosure.
4Drive Connector• Used to connect the Drive to the Enclosure.
USB 3.2 Gen 2 Type C IP67 Rugged NVMe Enclosure
5
Adjustable Drive
Length Holes
• Used to accommodate dierent drive lengths.
6
Drive-Mount Screw/
Nut
• Used to secure the Drive to the Enclosure.
Requirements
For the latest requirements and full manual, please visit www.startech.com/
M2E1BRU31C
Installation
Warning! Drives should be handled carefully, especially when they’re transported. If
you’re not careful with your drives, you may lose data as a result.
Installing an 80 mm Drive
1. Using the Torx Screwdriver (included), remove the Drive-Cover Screws (x 4) from
the bottom of the Enclosure and remove the Cover Plate.
2. Place the Drive next to the Drive Tray and align the screw groove on the Drive with
the Adjustable Drive Length Holes on the Drive Tray.
3. Use the Torx Screwdriver and to remove the Drive-Mount Screw from the
Enclosure.
4. Gently slide the connector on the Drive (on a 30-degree angle) into the Drive
Connector on the Enclosure.
Note: The connector on your drive is keyed so that it only ts one way.
5. Lightly push the Drive down into position on the circuit board.
6. Insert the Drive-Mount Screw through the screw groove on the Drive and into the
Drive-Mount Screw Hole on the Enclosure.
7. Using the Torx Screwdriver tighten the Drive-Mount Screw, being careful not to
over-tighten.
8. Place the Cover Plate back onto the bottom on the Enclosure. Make sure that the
Cover Plate is properly aligned with the top of the Enculosure creating a tight seal
and that nothing is obstructing the Cover Plate, in order to provide a water and
dust resistance seal.
9. Insert the Drive-Cover Screws back into the four corner on the bottom of the
Enclosure.
6
4
5
3
1
2
Produktspecifikationer
| Varumärke: | StarTech.com |
| Kategori: | Extern hårddisk |
| Modell: | M2E1BRU31C |
Behöver du hjälp?
Om du behöver hjälp med StarTech.com M2E1BRU31C ställ en fråga nedan och andra användare kommer att svara dig
Extern hårddisk StarTech.com Manualer
StarTech.com IDE2SAT2 Bruksanvisning StarTech.com SMS2BU31C3R Bruksanvisning StarTech.com S251BU31315 Bruksanvisning StarTech.com S2510BPU337 Bruksanvisning StarTech.com S251BRU33 Bruksanvisning StarTech.com SM22BU31C3R Bruksanvisning StarTech.com S352BU313R Bruksanvisning StarTech.com S251BMU313 Bruksanvisning
Alla StarTech.com Extern hårddisk manualer
Populära i Extern hårddisk
StarTech.com S2510BPU33 Bruksanvisning StarTech.com 25SATSAS35 Bruksanvisning StarTech.com SATSASDUPE11 Bruksanvisning
Extern hårddisk Manualer
Nyaste Extern hårddisk Manualer
Icy Box IB-3640SU3 Bruksanvisning Icy Box IB-AC603b-U3 Bruksanvisning Icy Box IB-1121-C31 Bruksanvisning ADATA HV300 Bruksanvisning ADATA AHV620S Bruksanvisning Silicon Power Bolt B75 Bruksanvisning Sabrent EC-TFNE Bruksanvisning Icy Box IB-200T-C3 Bruksanvisning ADATA SC685 Bruksanvisning Seagate STEB2000100 Bruksanvisning