Summit OTR24 Bruksanvisning

Summit Magnetron OTR24

Läs gratis den bruksanvisning för Summit OTR24 (3 sidor) i kategorin Magnetron. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.0 stjärnor baserat på 8.5 recensioner. Har du en fråga om Summit OTR24 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

IMPORTANT

Installation Kit

120 92-3008P

Before starting, compare items on your invoice with items

received. Carefully check through packaging material.

If an item is missing, please call:

Crutchfield

Parts Supplied:

Kit Frame

Support Tray

Chevrolet

Revision 09/17/03

Kit assembly instructions are on the following pages.

Page 1 of 3

*120923008P*

Mounting Brackets

Left

Right

(2) Studs (2) 3/8” Nuts

(4) 1/4” Hex Screws

Trimplate

at 1-888-955-6000

FIGURE 2

Shaft Supports

Installation Kit

120 92-3008P

Chevrolet

1. Press posts on trimplate kitinto holes on

frame to snap parts together and secure with hex

screws (Figure 1).

2. Use a utility knife to cut out shaft supports in

trimplate to create a DIN opening (Figure 2).

3. Push clips on into slots on rear of kit support tray

frame to secure (Figure 1).

4. Select the right and left side mounting brackets.

Break off the tabs that are shown as shaded (Figure 3).

5. Secure mounting brackets to sides of kit frame with studs

and nuts supplied (Figure 1).

6. Remove DIN sleeve from receiver and slide into

opening in trimplate. Secure sleeve to trimplate by

bending the securing tabs (Figure 4).

7. Slide receiver into sleeve/kit assembly.

DIN Receiver Assembly

Securing Tabs

DIN Sleeve

Bend tabs after sleeve

is inside assembly.

FIGURE 1

Trimplate

Kit Frame

Support Tray

Left Mounting Bracket

Stud

Nut

Right Mounting Bracket

FIGURE 3

FIGURE 4

Break off

shaded tabs

Hex Screws

Tools Required

Utility

Knife

▲

Small Flat Blade

Screwdriver

1/4” & 3/8”

Sockets

Pliers

Installation Kit

120 92-3008P

Chevrolet

Spacers

(supplied with

your order)

1. Press posts on trimplate into holes on kit frame to

snap parts together and secure with hex screws

(Figure 1).

2. Push clips on into slots on rear of kit frame support tray

to secure (Figure 1).

3. Select the right and left side mounting brackets.

Break off all tabs shown as shaded (Figure 2).

4. Secure mounting brackets to sides of kit assembly with

studs nutsand supplied (Figure 1).

5. Choose the proper spacers (supplied with your order) to

allow receiver nosepiece to extend 1/8” to 1/4” beyond

face of trimplate (Figure 3).

6. Insert receiver shafts (with spacers in place) through

openings in trimplate. Secure receiver and faceplate

with shaftnuts supplied with receiver.

7. Attach control knobs.

1/8” -1/4”

▲

Spacer

Shaft Receiver Assembly

FIGURE 3

Shaftnuts

FIGURE 1

Trimplate

Kit Frame

Support Tray

Left Mounting Bracket

Faceplate

Control Knobs

Tools Required

▲

Deep Socket

(size depends upon receiver)

Stud

Nut

Right Mounting Bracket

FIGURE 2

Break off

shaded tabs

1/4” & 3/8”

Sockets

Hex Screws

Pliers

Produktspecifikationer

Varumärke:	Summit
Kategori:	Magnetron
Modell:	OTR24
Enhetsplacering:	Ingebouwd
Färg på produkten:	Roestvrijstaal
Inbyggd display:	Ja
Snäll:	Koffie
Husmaterial:	Roestvrijstaal
Strömförsörjning:	13 A
Tillgångar:	1350 W
Vattentankens kapacitet:	1.80 l
Kapacitet för kaffebönor:	220 g
Kaffebryggare typ:	Volledig automatisch
Kaffeinmatningstyp:	Coffee beans, Ground coffee
Inbyggd kvarn:	Ja
Varmvattensystem:	Ja
Att göra espresso:	Ja
Gör cappuccino:	Ja
Maximal arbetsbelastning:	15 bar
Mjölkbehållare:	Nee
Mått (B x D x H):	595 x 361 x 455 mm
Typ produkt:	Espressomachine
Type beeldscherm:	LCD
Flera drinkar:	Ja