Sunding JOY-583BT Bruksanvisning

Sunding Cykeldator JOY-583BT

Läs gratis den bruksanvisning för Sunding JOY-583BT (2 sidor) i kategorin Cykeldator. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 10.5 recensioner. Har du en fråga om Sunding JOY-583BT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

Set code table parameter by APP

See attached page for detailed settings.

Instructions

JOY-583BT

Thread ties through

the slots under the

base to attach to

handlebar

Match base

alignment with

computer and

insert to attach

Computer Installation

Attach the computer to the handlebar and secure using included ties. To check the

installation, spin the front wheel with the computer in speed mode and observe

whether there is output on the computer screen. Adjust sensor and magnet position

if signal is weak or nonexistent.

*Dry, cold weather may interfere with heartbeat monitor functionality. To resolve, wait

for a few minutes. You can also put a few drops of clean water on the heartbeat

monitor conductor.

Chest Belt

*Attach belt so SunDing logo can be seen

from outside, right side up. The belt must

be placed over the heart, with no clothing

or other material separating it from the body.

Installation

*Computer battery installation: Open the battery cover. Install two CR2032 batteries

with positive poles facing battery cover.

Battery Installation

*Speedometer and cadence sensor battery installation: Open the battery cover on the

bottom of the computer with a flathead screwdriver. Install CR2032 battery

with positive pole facing battery cover. Replace cover and tighten with screwdriver.

*Chest belt installation: Open the battery cover. Install CR2032 battery with positive

pole facing battery cover. Replace and tighten cover by turning right.

Computer

CR2032 Battery

Magnet

Sensor

Chest Belt

Multi-Magnet

Ties

Accessories

Installation of sensor

Computer Function Display Area

Maintenance Distance Setting(Figure 7)

Distance Countdown Setting mode (Figure 11)

Time Countdown Setting mode (Figure 12)

Menu Hidden Setting (Figure 10 45)、

In Menu Hidden Setting mode. Press SET button to enter Hide Total Odometer setting.

When “On” is flashing, the Total Odometer is shown. When “Off” is flashing, the Total

Odometer is hidden. Please see diagram on back for additional details.

Temperature Setting

Clock Setting (Figure 8)

Riders Weight Setting (Figures 6)

If you are unable to locate your tire

size on this chart, you can use the

method shown to the right to measure

the time diameter and calculate the tire

circumference. Circumference = diameter x 3.14

Initial Odometer Setting (Figure 4)

When the Initial Value of Odometer setting mode is selected, press the MODE button to

enter it. To adjust the selected figure, press the MODE button, and press the SET button to

confirm your value and move to the next field. Press the SET button once finished with

Initial Odometer Setting to move onto the Initial Time setting.

Initial Time Setting (Figure 5)

When the Initial Time setting mode is selected, press the MODE button to enter it. To adjust

the selected figure, press the MODE button, and press the SET button to confirm your value

and move to the next field. Value ranges from 0 to 99,999 hours. Press the SET button once

finished with Initial Time setting to move onto Riders Weight setting.

When the Riders Weight setting mode is selected, press the to set weight MODE

measurement unit (KG LB or ) and press button to move to set weight. Use the SET

MODE button to adjust flashing number for weight, and press to confirm and SET

advance to next digit. The default weight is 65 KG, any value from – entered. Press 0 299

MODE button to confirm value and enter into Clock setting mode.

In Temperature Setting mode, hold button for SET 3

seconds to toggle between Celsius and Fahrenheit.

When “24” flashes in Clock mode, press MODE button to toggle between 12 and 24 hour time

format. Press SET to confirm and move to Hour setting. Press MODE button to adjust flashing

Hour value, and press SET to confirm and move to Minute setting. Press MODE button to adjust

flashing Minute value, and press SET to confirm and enter into Date setting.

In the mileage countdown mode, long press the SET button for 3 seconds to enable the

mileage value jump. Press the MODE button to adjust the value of jump mileage. Press the

SET button to change the digit. The setting range is 0~9999.9KM/ML. After completion,

press the SET button and return the mileage countdown mode.

In the time countdown mode, long press the button for 3 seconds to enable SET

countdown “hour” jump. Press the button to adjust this value, and press the MODE SET

button to change the digit. Press the button to enable “minutes” value jump, and press SET

MODE button to adjust this value. Press the button to change the digit. The setting SET

range is 0 999:5 hours. After completion, press the button and return the time ～SET

countdown mode.

Date Setting (Figure 9)

In Year Setting mode, press MODE button to adjust year, then press SET button to confirm

and move to Month Setting mode. In Month Setting mode, press MODE button to adjust

month, then press SET button to confirm and move to Day Setting mode. In Day Setting

mode, press MODE button to adjust the date, and press SET to move to Week Setting mode.

In Week Setting mode, press MODE button to adjust week, and press SET to confirm and

move to Distance Countdown Setting mode.

Panoramic Display Setting mode (Figure 47)

In Panoramic Display Setting mode, hold SET button for 3 seconds to toggle Panoramic

Display. When the digit on the first row is flashing, press the MODE button to adjust it. Press

SET button to confirm and move on to the next row. Please see

diagram on back for additional details.

Menu Cycle Setting mode (Figure 44)

In Menu Cycle Setting mode, press the SET button for 3 seconds to enter Menu Cycle

Setting. Press SET button again to enter Total Odometer Cycle Setting. When “Out” is

flashing, it represents the Total Odometer withdrawn from the Cycle mode. Press the

MODE button toggle “Join” mode. When “Join” is flashing, it represents the Total

Odometer added to the Cycle mode. Press the SET button to confirm and enter into Trip

Cycle Setting. Please see diagram on back for additional details. Panoramic Display mode

may not be exited from this menu.

Chain wheel / Flywheel Setting mode (Figure 46)

In Cadence Gear Ratio mode, hold SET button for 3 seconds to enter into Flywheel

Parameter Setting. The small digits at the top of the display represent the flywheel

parameters. The number of the flywheel is displayed in descending order. If there is no

flywheel, the display will show 0. The small digits at the lower part of the display represent

the chain wheel parameters. The number of chain wheel is displayed in descending order;

the display will show 0 if there is no chain wheel. Please see diagram on back for additional

details.

In Clear Signal Data mode, hold button for SET 3

seconds to clear all signal data.

Clear Signal Data

IN MAINTENANCE DISTANCE mode, press the button to change the number of MODE

digital, and press the button confirm and advance. Default value ,and its ranges SET :200

from 200 to 800KM. Press the button to confirm and enter into CLOCK SETTING. MODE

Date cleared

1 2

Mounting Shoe & Wired Remote Control

Heart Rate Monitor

3.Adjust the magnets and the sensors, making sure the air gap between sensor markings

and magnets is less than 3mm, when setup is complete, tighten the cable tiles.

1.Pass the bandage through the

bottom hole of the tread device.

2.Use the supplied cable ties to hold the

sensor in place, Do not fully tighten,

Attach the magnet to a spoke, Do not

fully tighten.

Notice

Pass bicycle spokes through the

plastic hole on the bottom of the

magnet and tighten to secure

The magnet is designed for spokes

that are less than 2mm thick

Back

CONTACT

BATTERY

COVER

SLOT

Stopwatch Function Operation

Parameter Setting

Digital Adjust

TM DN Setting





Option Switching And Digital Adjustment

In TRIP DN

MODE ,press

the SET button

In TTM MODE ,

press the SET

button

Press the

SET button for 3

seconds in

ODO or TTM

MODE to enter

into Language

setting menu



















 



 



 









 





press

for 3s

reset









FUNCTIONS

-SPEED (0~99 9 KM H M H )    

- TOTAL ODOMETER ODO (0~99999KM H) (Fig 14)

-DAY DISTANCE DST (Fig 15)

- AVG SPEED AVS (Fig 16)

- MAX SPEED MAS (Fig 17)

- RIDE TIME TM (0~99:99hrs) (Fig 18)  

- TOT TIME TTM    (0~99999hrs ) (Fig 19)

- TEMP (-20°C~70°C / -4°F~158°F) (Fig 20)

- MIN TEMP MIT (Fig 21)

- MAX TEMP MAT (Fig 22)

- STOPWATCH STP (Fig 23)

-TRIP DDN (Fig 24)

- TIME TDN   Fig 25

-GEAR RATIO RAT  Fig 26

-MAX CAD (Fig 27)

-AVG CAD ACD (Fig 28)

-MAX H/R MHT (Fig 29)

-AVG H/R AHT (Fig 30)

-CALORIE CAL (Fig 31)

-FAT BURN FAT (Fig 32)

-SLOPE% SLP (Fig 33)

-MAXSLOPE MXL (Fig 34)

-ALTITUDE ALT (Fig 35)

-HI-ALTITUDE HIA  (Fig 36)

-CLIMB HT CHT (Fig 37)

-PRESSURE ATMOSPHERIC PRESSURE PRS (Fig 38)

-MIN PRES MIP (Fig 39)

-CLOCK (12/24H)

-DATE (YY/MM/DD/WW)

PARAMETER SETTINGS

-MULTI-LANGUAGE SETTING (CN / UK DE FR IT ES / / / / /

SE NL ) (Fig 1) /

-KM / M (Fig 2)

-CELSIUS / FAHRENHEIT

-WHEEL SIZE (Fig 3)

-INITIAL ODOMETER VALUE (KM / M) (Fig 4)

-INITIAL CHRONOMETER VALUE (Fig 5)

-METRIC / IMPERIAL SETTING (Fig 6)

-MAINTENANCE DISTANCE (Fig 7)

-CLOCK (Fig8)

-DATE (Fig 9)

-DISTANCE COUNTDOWN (Fig 11)

-TIME COUNTDOWN (Fig 12)

-MENU CYCLE (Fig 44)

-CHAINWHEEL / FLYWHEEL (Fig 46)

-HIDE MENU (Fig 10 45)、

-PANORAMIC DISPLAY (Fig 47)

AUXILIARY MODE

-PANORAMIC DISPLAY MODE (Page 2, Figs 40, 41, 42)

-MENU CYCLE MODE (Fig 43)

-SPEED COMPARISON

-HIDE MENU MODE

-MAINTENANCE ALERT

-LOW BATTERY INDICATOR

-WIRELESS WAKE UP

-SMART BACKLIGHT

-L

-SECOND

CR2032Battery

Battery Cover

Connection of code table and mobile phone

Long press the button for 3 seconds, the mobile phone symbol jumps, open the MODE

Lite APP, click My device, click the connection after finding smart code table, and

connect the mobile phone symbol successfully to stop beating.

● Heart rate monitor, tread device and code table connection, calculated Main mode:

motion data is saved and uploaded to the mobile phone. The motion data calculated is

saved and uploaded to the mobile phone.

●Slave mode (mirror data): The heart rate monitors and tread device are connected to

the mobile phone. The motion data calculated by APP is transmitted to the code table

through Bluetooth, and the code table only displays the motion data of APP. In the slave

mode, the code table displays that the animation of the wheel is a hollow.

●Code table parameter setting by mobile phone: Enter code table setting page of the

APP, you can set the parameter of code table, scan, bind and unbind external device of

code table. Click "complete setting" to change the parameters of code table when the

parameter setting is complete, and the time of code table will also be synchronized to

current time of mobile phone. Click data download to upload riding data of code table

to your mobile phone.

Note: It can only be uploaded to the APP after the code table is synchronized with the

mobile phone to start the data of riding.

Connection of code table with device and mobile phone

Front

CADENCE

SPEED

HEART RATE

CLOCK

FUNCTION

SET

MODE

LOW BATTERY

INDICATOR

CADENCE

CONTRAST

SPEED

COMPARISON

MAINTENANCE

REMINDERS

ROTATION

ANIMATION

Data uploading

Parameter setting

Slave mode

www.joycune.com

TRIP DN Setting

Wheel Size Setting

Parameter Settings

KM / M Setting

Language Setting

Tire Size Chart (in mm)

Press button to select or , and press Set button to confirm and enter into MODE KM M

Wheel Size Setting.

In Wheel Size Setting mode, The default is mm. select wheel circumference based 2155

on below chart. Press the button to change each figure, and press to confirm MODE SET

and move on to next setting. Afterwards, press to enter into Odometer Setting mode.SET

To set language, remove and reinstall battery, or hold button for seconds in or SET 3 ODO

TTM MODE SET Mode. Select language using button, and press button to confirm and

enter into / Setting.KM M

Bluetooth device connection

Long press key in any mode to start Bluetooth device binding and enter the SET+MODE

mobile phone connection page.

Mobile phone connection: MODE Long press the button to start mobile phone

connection scan APP to enter the device connection and click the code table scan. It will

automatically return to the phone connection page after successful connection. If the

phone is not found, press key to manually return or automatically return to the SET

phone connection page after 30 seconds. Under the phone connection page, press the

MODE button to enter the exit mode of slave mode, and then press the MODE button to

confirm exit and return to the phone connection page. Press to enter the binding SET

speed page.

Tread device binding: MODE Under the binding speed page, long press the button to

start the tread device binding scan, and induce tread device with the magnet. After

successful binding, it will automatically return to the binding speed page. If the phone is

not found, press key to manually return or automatically return to the binding speed SET

page after 30 seconds. Under the binding speed page, press Mode key to enter the tread

device unbinding setting, and then press the button to confirm exit and return. MODE

Under the binding speed page, press the SET button to enter the binding heart rate page.

Heart rate monitor binding: Wear a heart rate monitor properly. Under the binding

heart rate page, long press the button to start the heart rate scan. If the heart MODE

rate monitor is not found, press the button to manually return or automatically SET

return to the binding heart rate page after 30 seconds. Under the binding heart rate

page, press the button to enter the heart rate unbinding setting, and then press MODE

the button to confirm and return to the binding heart rate page. Press the MODE SET

button to complete the device binding.

Long press button in any mode to enter the scanning status of Bluetooth device, MODE

and the Bluetooth symbol of mobile phone will jump. After successful connection, the

symbol stops jumping and displays for a long time, and the symbol will disappear when

the device is not found after 10 seconds.

Bluetooth device binding

CR2032

+CR

2032

Tire Size

Circumference

Tire Size

Circumference

Tire Size

Circumference

12×1.75 935

12×1.95 940

14×1.50 1020

14×1.75 1055

16×1.50 1185

16×1.75 1195

16×2.00 1245

16×1-1/8 1290

16×1-3/8 1300

17×1-1/4 1340

18×1.50 1340

18×1.75 1350

20×1.25 1450

20×1.35 1460

20×1.50 1490

20×1.75 1515

20×1.95 1565

22×1-3/8 1770

22×1-1/2 1785

24×1.75 1890

24×2.00 1925

24×2.125 1965

24×1(520) 1753

24×/34Tubular 1785

24×1-1/8 1795

24×1-1/4 1905

26×1(599) 1913

26×1.25 1950

26×1.40 2005

26×1.50 2010

26×1.75 2023

26×1.95 2050

26×2.10 2068

26×2.125 2070

26×2.35 2083

26×3.00 2170

26×1-1/8 1970

26×1-3/8 2068

26×1-1/2 2100

26×7/8 1920

650×20C 1938

650×23C 1944

650×25C 1952

650×38A 2125

650×38B 2105

27×1(630) 2145

27×1-1/8 2155

27×1-1/4 2161

27×1-3/8 2169

27.5×1.50 2079

27.5×1.95 2090

27.5×2.1 2148

27.5×2.25 2182

700×18C 2070

700×19C 2080

700×20C 2086

700×23C 2096

700×25C 2105

700×28C 2036

700×30C 2146

700×32C 2155

700Tubular 2130

700×35C 2168

700×38C 2180

700×40C 2200

700×42C 2224

700×44C 2235

700×45C 2242

700×47C 2268

29×2.1 2288

29×2.2 2298

29×2.3 2326

114

The function mode and operation (If the mode is not displayed, enter the Blanking Settings menu and open it)

Driving parameter settings

Choose menu

cycle mode

°C/°F switch

Stopwatch function

operation

Setting

TRIP D N

Setting

TM DN

Setting the parameter of the

flywheel andchainwheel

Numerical

reset

Cycle menu setting

Panoramic display

setting

Menu hidden setting

Digital adjustment

Menu hidden

switching of

the switch

115

116

66 1

117

77 1

118

88 1

119

220

221

222

223

33 2

224

225

226

229

99 3

330

00 3

331

11 32

3232 3

333

33 3

334

44 3

335

55 36

3636 3

337

77 3

338

88 3

339

440

443

445

press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s press SET for 3s

press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s press MODE for 3s

TEMP (Temperature)

MAX-TEMP (Maximum Temperature)

TEMP displays the current temperature, ranging from -20°C to 70°C, or - 4°F to

158°F.

MAX-TEMP displays the maximum temperature of a single trip.

MIN-TEMP (Minimum Temperature)

MIN-TEMP displays the minimum temperature of a single trip.

TOT TIME (Total Time)

AVGSPEED (Average Speed)

RIDETIME (Riding Time)

SPEED (Current Speed)

TOTALODO (Total Odometer)

DIST.DAY (Daily Distance)

FUNCTION DESCRIPTIONS

MAXSPEED (Maximum Speed)

MAXSPEED displays the maximum speed reached during a single trip.

AVGSPEED displays the average speed of a single trip.

The current speed is displayed on the screen at all times. It ranges from

0 99.9 KM/H MPH +/- 0.1 KM/H MPH– or , and is accurate to or .

TOT TIME displays the total duration of a single trip. Hold the SET button for 3

seconds in this mode to adjust the parameter.

The Total Odometer will display all distance accrued while computer is active,

ranging from 0.01 to 99,999 KM/M. Hold the SET button for 3 seconds in this

mode to adjust the parameter.

RIDETIME displays the amount of time riding of a single trip, ranging from 0:00:00

to 99:59:59, and will reset to zero once the maximum value has been reached.

The Daily Distance will display all distance accrued since last reset. It ranges

from 0.01 to 99,999 KM/M, and will reset to zero once the maximum value has

been reached.

MAX CAD (Maximum Cadence)

MAX CAD displays the maximum cadence of a single trip, in beats per minute.

The Maximum Cadence is cleared when the date is reset.

TRIP DDN (Trip Distance Countdown)

TIME TDN (Trip Time Countdown)

GEARRATIO (Gear Ratio)

CAD (Current Cadence)

AVG CAD (Average Cadence)

GEARRATIO will display 3:1 or 8:1. 3:1 indicates that the chain wheel has a 3 fluted

disc, while 8:1 indicates that the chain wheel has an 8 fluted disc, with ratio of the first

chain wheel being recommended based on speed. Recommended cadence for flat

terrain is 90, while recommended cadence for sloped terrain is 75. Reference

Chain wheel/Flywheel setting from previous section for more information.

STPWATCH (Stopwatch) (Figure 13)

AVG CAD displays the average cadence of a single trip, in beats per minute. The

Average Cadence is cleared when the date is reset.

Set a mileage to be completed when start riding, and begin to count down from

the set mileage after riding.

Set a time to be completed when start riding, and begin to count down from the

set time after riding.

In STPWATCH mode, press SET button to start the timer. Press SET again to

stop the timer, and press MODE to clear data.

CAD displays the current cadence in the upper right corner of the screen, in beats

per minute. When no cadence is detected, 000 will be displayed. If “Up” flashes,

it is an indication that the current cadence is below the recommended level. If

“Down” flashes, it is an indication that the current cadence is above the

recommended level.

Panoramic Display Mode

Date (Year, Month, Day, Week)

AUXILIARY MODE AND FUNCTIONS

In sleep mode, the current date is displayed.

Clock (24H / 12H)

The time is displayed at the bottom of the display, except in Panoramic Mode.

Heart Rate

The current Heart Rate is displayed in the upper left corner of the screen, in beats

per minute. When there is no signal, the display will show . The Heart Rate 000

symbol will flash when a heart rate is detected.

Remote Control

Low Battery Indicator

Speed Comparison

Menu Hidden Mode

Menu Cycle Mode

If the voltage remaining is less than , the Low Battery Indicator will flash as a 2.7V

reminder to change the battery.

Panoramic Display Mode allows for the selection of up to three different functions to

be displayed concurrently on the screen. Press to customize which data will MODE

be displayed, and press to move on to the next display. First function is SET

displayed by default, while second and third are hidden by default.

Maintenance Alert

Wireless Auto Wake-up

Shake the handlebar to disable Sleep Mode.

Smart Backlight

The Smart Backlight will activate when there is insufficient light. Press any button to

turn on the Backlight for seconds.5

When the Odometer value exceeds the set maintenance mileage, the

Maintenance Alert indicator (wrench) will flash as a reminder that maintenance is

necessary. Hold the button to clear the Maintenance Alert indicator.SET

The wired remote control allows for access to the button without removing MODE

your hand from the handlebar.

Press and hold the Mode button to enter Menu Hidden Mode. The first page of the

Panoramic Display cannot be hidden.

The Speed Comparison displays your current speed in comparison to the average

speed. When above average speed, the arrow will point upwards, and when below

average speed, the arrow will point downwards.

In the panoramic mode, press the MODE button to enter the menu cycle mode.

Except Panorama 1 page, all functions can be set to join or exit the cycle mode.

The menu that is added to cycle mode can cycle and display in 4s, and blanked

menus must be blanked before they can be added to cycle mode.

TROUBLESHOOT ING

Error

Cause

Tread device and heart

rate monitor cannot be

connected

1.Check the battery capacity of tread device and heart

rate monitor.

2. Check if the tread device and heart rate monitor are

installed correctly, heart rate monitor is worn correctly.

If the heart rate monitor is too dry hen contacting with

the skin, and it can be wet with water.

3. Start Bluetooth scanning.

4. The tread device and heart rate monitor have been

connected to the mobile phone or another code table.

Stop sensing and wait 5 minutes before connecting.

5. The code table has been bound to another tread

device and heart rate monitor. When removing binding,

it needs to be reconnected.

6.The code table is set to slave mode.

APP cannot download

the riding data of code

table

Fail to synchronize with the current mobile phone:

Before riding, it needs to connect with the current

mobile phone to enter the parameter setting page to

save and exit. The clock time of code table is the same

as the clock time of current mobile phone.

Blank screen

The temperature is too high or the exposure time is too

long in the sunshine, and it will return to normal after

being placed in the shadow for a while.

The display screen is

faint, missing segment

If the battery is not in good contact or the battery runs

out, please check the battery installation or replace the

battery.

Second

The computer is connected to the mobile phone, and the movement value of the

mobile phone is uploaded to the code table and displayed.

Press SET+MODE

for 3 seconds

Flywheel and chainwheel parameter setting

446

Cycle menu settings

press the

SET button

for 3s

444

Setting method for connection mobile phone (as shown below)

Complete setting

press SET for 3s

press MODE for 3s

441

11 4

442

227

press SET for 3s

press MODE for 3s

228

HI-ALTIT (Highest Altitude)

ALTITUDE (Altitude)

CLIMB HEIGHT

HI-ALTIT displays the Highest Altitude of a single trip. The Highest Altitude is

cleared when the date is reset.

The amount of climb height in single trip, unit: meter. The is cleared climb height

when the single date is clear.

ALTITUDE displays the current altitude, calculated using barometric pressure. Please

note that weather may impact barometric pressure, resulting in reading discrepancies

depending on current conditions.

FAT BURN (Fat Burned)

For total fat from last reset of code table to the current driving process, the counting

range is 0~9999.9kg .

CALORIE (Calories Expended)

MAX H/R (Maximum Heart Rate)

AVG H/R (Average Heart Rate)

AVG H/R displays the Average Heart Rate of a single trip, in beats per minute.

Average Heart Rate is cleared when the date is reset.

MAX H/R displays the Maximum Heart Rate of a single trip, in beats per minute.

Maximum Heart Rate is cleared when the date is reset.

For total heat consumed from last reset of code table to the current driving process, the

counting range is 0 9999kcal.～

MAXSLOPE

The maximum slope of riding road in a single stroke.

SLOPE%

The slope of current riding road.

Panoramic display setting

Select menu

447

B C D E

Bluetooth

Scanning

Numerical

reset

Bluetooth

Scanning

Start Bluetooth scanning

Press and hold the

MODE button

PRS (Pressure Atmospheric Pressure)

The air pressure of current riding road.

MIP (Min Pres)

The barometric minimum in a single riding stroke.

Produktspecifikationer

Varumärke:	Sunding
Kategori:	Cykeldator
Modell:	JOY-583BT
Enhetsplacering:	Vrijstaand
Typ av operation:	Knoppen
Inbyggd display:	Ja
Vikt:	47300 g
Bredd:	598 mm
Djup:	600 mm
Höjd:	850 mm
Nettoskatt:	1800 W
Antal platsinställningar:	15 couverts
Torksystem:	Statisch
Fördröjd starttimer:	Ja
Startfördröjning:	24 uur
Barnlås:	Ja
Ljudnivå:	44 dB
Energie-efficiëntieklasse:	D
Förpackningens vikt:	50000 g
Förpackningens bredd:	644 mm
Djuppackning:	661 mm
Förpackningshöjd:	889 mm
Vattenförbrukning per cykel:	9.9 l
Var klass:	A
Nuvarande:	13 A
Bulleremissionsklass:	B
Antal tvättprogram:	6
Cykelns längd (snabbtvättprogram):	30 min
Energiförbrukning per 100 cykler:	86 kWu
Djup när dörren är öppen:	1150 mm
Typ av bästa fack:	Mand
Kåpa material:	Roestvrijstaal
Fötter justering:	15 mm
Varningssignal:	Nee
Saltindikator:	Ja
Sköljmedelsindikator:	Ja
Översvämningsskydd:	Ja
Antal temperaturinställningar:	5
Halvlastad:	Ja
Tvättprogram:	Auto, Eco, Express, Intensive, Mini, Prewash, ProCare, Steam
Energiförbrukning per cykel:	0.861 kWu
Avloppsslangens längd:	1.3 m
Nedräkning:	Ja
Övre korg justerbar höjd:	Ja
Nedre kupan:	Vouwbaar
Höjd under bänkskiva:	820 mm
Vattentillgång:	Koud
Övre korgställ:	Vouwbaar
Rinse Plus-funktion:	Ja
Maximal fatstorlek (lägsta korgen):	29.5 mm
Slangdiameter:	16 mm
Övre korg justerbar höjdnivåer:	3
Lägsta vattentryck:	300 kPa
Maximalt vattentryck:	1000 kPa
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 Hz
Type beeldscherm:	LCD
Typ motor:	Geborsteld
Nödvändiga verktyg:	Standard tool box
Värmekraft:	1800 W
Justerbar vattenavhärdare:	Nee
Maximal fatstorlek (övre korg):	18.5 mm
Antal övre korgställ:	3
Expanderad polystyren (EPS) förpackningsvikt:	530 g
Extra besteklade:	Ja
Uttagbar bestickkorg:	Ja
Justerbar sköljdosering:	Ja
Diskmedelstablettfunktion:	Ja
Vikt av pappersförpackning:	700 g
Vikt av plastförpackning:	205 g
Vikt av metallförpackning:	12 g
Vikt av träförpackning:	450 g
Lämplig för slangförlängning:	Ja
Professionell installation krävs:	Ja
Retention av reservdelar:	7 jaar
Eco-programmets varaktighet:	245 min
Justerbara koppställ översta korg:	Ja
Fällbara tänder nedre korg:	4
Anslutningsvärde (max):	2100 W
Möbeldörr krävs:	Nee
Super glans funktion:	Ja
Hygien+ funktion:	Ja