System Sensor B300-6-BP Bruksanvisning

System Sensor Detektor B300-6-BP

Läs gratis den bruksanvisning för System Sensor B300-6-BP (2 sidor) i kategorin Detektor. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 13 recensioner. Har du en fråga om System Sensor B300-6-BP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

BEFORE INSTALLING

Please read the System Smoke Detectors Application Guide, which provides

detailed information on detector spacing, placement, zoning, wiring, and spe-

cial applications. Copies of this application guide are available from System

Sensor. NFPA 72 guidelines should be observed.

NOTICE: This manual should be left with the owner/user of this equipment.

IMPORTANT: The detector used with this base must be tested and maintained

regularly following NFPA 72 requirements. The detector should be cleaned at

least once a year.

GENERAL DESCRIPTION

The B300-6 and B300-6-IV are plug-in detector bases intended for use in an

intelligent system, with screw terminals provided for power (+ and –), and

remote annunciator connections. Communication takes place over the power

lines (+ and –).

BASE TERMINALS

NO. FUNCTION

1 Power (–), Remote Annunciator (–)

2 Power (+)

3 Remote Annunciator (+)

FIGURE 1. TERMINAL LAYOUT

TERMINAL 1

TERMINAL 2

TERMINAL 3

C0127-07

MOUNTING

This detector base mounts directly to 4-inch square (with and without plaster

rings), 4-inch octagon, 3

1/2-inch octagon, and single gang junction boxes. To

mount, remove the decorative ring by turning it in either direction to unhook

the snaps, then separate the ring from the base. Install the base on the box

using the screws supplied with the junction box and the appropriate mounting

slots in the base.

Place the decorative trim ring on the base and rotate it in either direction until

it snaps into place. (See Figure 2.)

SPECIFICATIONS

Base Diameter: 6.1 inches (155 mm)

Base Height: 0.76 inches (19 mm)

Operating Temperature: Refer to applicable sensor Operating Temperature Range using the Base/Sensor Cross Reference Chart at systemsensor.com.

Electrical Ratings:

Operating Voltage: 15 to 32 VDC

Standby Current: 170 µA

Listings: UL268

I56-6566-001

FIGURE 2. MOUNTING DETECTOR TO BOX

SNAP ON

DECORATIVE

RING

SCREWS

(NOT SUPPLIED)

DETECTOR

BASE

BOX

(NOT SUPPLIED)

C2036-01

INSTALLATION AND WIRING GUIDELINES (SEE FIGURE 3)

All wiring must be installed in compliance with all applicable local codes

and any special requirements of the authority having jurisdiction. Proper wire

gauges should be used. The conductors used to connect smoke detectors to

control panels and accessory devices should be color-coded to reduce the like-

lihood of wiring errors. Improper connections can prevent a system from re-

sponding properly in the event of a fire.

For signal wiring (the wiring between interconnected detectors), it is recom-

mended that the wire be no smaller than 18 AWG (0.823 mm²). Wire sizes up

to 12 AWG (3.31 mm²) may be used with the base.

Make electrical connections by stripping about

3/8 inch (10 mm) of insulation

from the end of the wire (use strip gauge molded in base). Then slide the wire

under the clamping plate and tighten the clamping plate screw. Do not loop

the wire under the clamping plate. (See Figure 4.)

Check the zone wiring of all bases in the system before installing the detec-

tors. This includes checking the wiring for continuity, correct polarity, ground

fault testing and performing a dielectric test.

The base includes an area for recording the zone, address, and type of detec-

tor being installed. This information is useful for setting the detector head

address and for verification of the detector type required for that location.

Once all detector bases have been wired and mounted, and the loop wiring

has been checked, the detector heads may be installed in the bases.

B300-6 and B300-6-IV

6" Plug-in Detector Bases

1 I56-6566-001

11/17/2017

Produktspecifikationer

Varumärke:	System Sensor
Kategori:	Detektor
Modell:	B300-6-BP
Vikt:	560 g
Typ av seriell anslutning:	RS-232/422/485
Antal Ethernet LAN (RJ-45)-portar:	2
Certifiering:	CE, FCC
Inspänning:	12 - 48 V
Ethernet LAN, dataöverföringshastigheter:	10, 100 Mbit/s
Förvaringstemperatur:	-40 - 85 °C
Nätverksprotokoll som stöds:	ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, Rtelnet, DNS, HTTP, SMTP, SNTP, IGMP
Säkerhet:	UL-508
Mått (B x D x H):	45.8 x 134 x 105 mm
Seriell port(ar):	4
Förvaltningsprotokoll:	SNMP v1
Drifttemperatur (TT):	-40 - 75 °C
Relativ luftfuktighet i drift (VV):	5 - 95 procent
Isolering:	1.5 kV
Anslutningslysdioder:	Ja