Tactical Fiber Systems CCRT241 Bruksanvisning
Läs gratis den bruksanvisning för Tactical Fiber Systems CCRT241 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 3.5 stjärnor baserat på 12.5 recensioner. Har du en fråga om Tactical Fiber Systems CCRT241 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
1525 NW 3
rd
Street, Deerfield Beach, FL 33442 877-777-7147 www.TacticalFiber.com
TFS ClearCom/RTS 2 wire to 4 wire InterCom Interface - Mod.CCRT242
Installation and Operating Instructions with ATEM Studio Converter 2
Product Description
TFS's CCRT24 interface connects a 2 wire Clear-Com or RTS base station to the Blackmagic ATEM Studio
Converter or Studio Converter 2 's four wire intercom system . The Clear-Com or RTS base station
becomes the master intercom and communicates to both wired or wireless party line/matrix belt-paks
and the ATEM camera converters linked to the Studio Converter over fiber.
Installation
Connect the Clear-Com or RTS base station to the CCRT24 interface using a 3PIN XLR cable from any
intercom output channel. NOTE: The CCRT24 is powered by the Clear-Com or RTS base station.
Connect the ATEM Studio Converter to the CCRT24 interface using the interface cable designed for
STUDIO CONVERTER 2. (Note: The original STUDIO CONVERTER comes with a different cable.) One end
has a 16 pin DIN connector which attaches to the CCRT24. The other end has two break-out cables for
connection to the Studio Converter's Mic and Headset sockets. Insert the BLACK .20" connector plug
into the MIC input and the grey 1/4" TRS plug into the HEADSET sockets on the Studio Converter.
DIP Switch Positions
The dip switch settings at the rear of the CCRT241 should be set as follows:
Switch 1 - ON (up)
Switch 2 - ClearCom - OFF (down) RTS -ON(up)
Calibrating the Interface
Your TFS CCRT24 Clear-Com/RTS interface was factory nulled with an MS-702 Clear-Com base station
attached to a Blackmagic ATEM Studio Converter. You may have to tweak the null adjustments to match
your particular Studio converter using an ear set and a small screwdriver. To null the interface, plug in
the ear set into the 1/8" jack to the right of the interface and adjust the RLC trim pots for minimum
noise...then unplug the ear set. IMPORTANT: You must unplug the ear set after nulling the interface
Produktspecifikationer
| Varumärke: | Tactical Fiber Systems |
| Kategori: | Inte kategoriserad |
| Modell: | CCRT241 |
Behöver du hjälp?
Om du behöver hjälp med Tactical Fiber Systems CCRT241 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Tactical Fiber Systems Manualer
24 September 2024
22 September 2024
Inte kategoriserad Manualer
- Rittal
- Danfoss
- Radio Flyer
- Bryton
- Four Hands
- ShelterLogic
- RC Allen
- Jabsco
- Milectric
- Amazon
- WesAudio
- Prixton
- Western Digital
- Stadler Form
- Meade
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025