TEF ZEOS-C Bruksanvisning

TEF Inte kategoriserad ZEOS-C

Läs nedan 📖 manual på svenska för TEF ZEOS-C (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

www.tefbrandbeveiliging.nl Tel: 0180 - 554555

FIRE ALARM DETECTOR

TECHNICAL SPECIFICATIONS

INSTALLATION

INSTALLING THE BASE

To ensure proper fit of the detector head to the base, all wires should be properly dressed at installation by positioning all wires flat

against terminals and fastening the wires away from connector terminals. The detector base can be mounted directly onto most standard

electrical junction boxes.

INSTALLING THE HEAD

Align detector components using provided alignment marks on both the head and base. Align detector mark and short alignment mark on

base. Fit the detector head onto the base and twist clockwise to secure it. After all detectors are installed, apply power to the control unit .

Test the detectors as described below.

TESTING

All remote signalling systems, releasing devices and extinguishing systems should be disconnected during the test period and

reconnected at the conclusion of testing. After powering the detector, check to see the indicator LED flashing every 5 seconds. If the LED

fails to flash, it indicates the non-functioning of the detector or fault wiring. Re-check the wiring or replace the detector if necessary.

SMOKE: Allow smoke from a cotton wick or test smoke aerosol to enter the detector’s smoke chamber for at least 10 seconds. When

sufficient smoke has entered, the detector will signal an alarm. This will be indicated by the illumination of the 2 Red LEDs provided. Make

sure to clear smoke out of the chamber before resetting in order to keep the detector at its current sensitivity setting.

HEAT: The detector to be tested should be subject to a flow of warm air at a temperature of between 65°C and 80°C. This requirement can

be met by some domestic hair dryers. Switch on the warm airflow and check that the temperature is correct and stable. From a distance of

several cms, direct the airflow at the guard protecting the thermistor. The detector should alarm within 60 seconds. Upon alarm

immediately remove the heat source and check that the Red LEDs of the detector are illuminated. If a detector fails to activate within 60

seconds, confirm connections and programming. If necessary replace unit. Note: After testing, check that the system is returned to

normal operation. Notify the appropriate authorities that the testing procedure has been completed and the system is active again.

MAINTENANCE

The recommended minimum requirement for detector maintenance consists of annual cleaning of dust from the detector head using a

low power vacuum cleaner. >> DO NOT ATTEMPT TO DISASSEMBLE THE DETECTOR

Detector Head

Detector Base

Alignment Marks

ZEOS-C

ma_zeosc_01_010001_en_180716

MADE IN PORTUGAL - EU

10 V to 30 V DC

Heat: 7 uA / Smoke: 33 uA / Smoke & Heat: 35 uA

24 mA - Alarm LEDs

According to EN54-5 or/and EN54-7

0.5-2.5 mm²

20 seconds max.

White / ABS

95% RH Non-Condensing

0°C to 50°C / -10°C to 85°C

100 mm (D) x 50 mm (H) inc. base / 144 g inc. base

ORION, ORION MINI, ORION EX, ORION-PLUS, QUAD ZMU and ZMU

SUPPLY VOLTAGE

CURRENT - QUIESCENT

CURRENT - DEVICE IN ALARM

SENSITIVITY

CABLE SIZE

RESET/START-UP TIMES

COLOUR / CASE MATERIAL

MAX. HUMIDITY

NORMAL / TRANSIENT OPER. TEMPERATURE

DIMENSIONS / WEIGHT

COMPATIBILITY

ORDER CODE DESCRIPTION

ZEOS-C-S

ZEOS-C-H

ZEOS-C-SH

| CERTIFICATE |

PHOTOELECTRIC SMOKE DETECTOR

RATE OF RISE/FIXED TEMP HEAT DETECTOR

MULTISENSOR SMOKE & HEAT DETECTOR

1328-CPR-0705

1328-CPR-0706

1328-CPR-0704

MECHANICAL SPECIFICATION

www.tefbrandbeveiliging.nl Tel: 0180 - 554555

DETECTOR BASE - CONNECTIONS

NOTE: Positive terminal of remote indicator should be connected to terminal 4.

-Zone IN

PANEL

ZONE

First Detector

Last Detector

-Zone OUT

Remote

Indicator

E.O.L.

+Zone

Remote

Indicator

(*)

Install optional Schottky diode

to comply with BS5839

head removal clause.

Produktspecifikationer

Varumärke:	TEF
Kategori:	Inte kategoriserad
Modell:	ZEOS-C
Färg på produkten:	Zwart
Vikt:	910 g
Bredd:	50 mm
Djup:	162 mm
Höjd:	120 mm
Husmaterial:	Aluminium
Internationell säkerhetskod (IP):	IP30
Strömförbrukning (max):	10.08 W
Certifiering:	CE\nEN 61000-6-4 \nEN 61000-6-2\nIEC 60068-2-27\nIEC 60068-2-6
Inspänning:	9 - 48 V
Nätverksstandard:	IEEE 802.1D, IEEE 802.1p, IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Säkerhetsalgoritmer som stöds:	SNMP
Förvaringstemperatur:	-20 - 80 °C
Webbaserad hantering:	Ja
VLAN=support:	Ja
Auto MDI/MDI-X:	Ja
Virtuella LAN-funktioner:	Tagged VLAN, Port-based VLAN
Stapelbar:	Nee
Växlingskapacitet:	- Gbit/s
MAC-ställbar:	2000 entries
10G-stöd:	Nee
Dataflödeshantering:	Ja
IGMP snokar:	Ja
Växlingstyp:	Managed
Antal grundläggande switchande RJ-45 Ethernet-portar:	7
Konsolport:	RS-232
Typ grundläggande switchande RJ-45 Ethernet-portar:	Fast Ethernet (10/100)
Antal modulplatser SPF:	2
Spanning tree protokoll:	Ja
Koppar Ethernet-kabelteknik:	10BASE-T, 100BASE-TX
Automatisk förhandling:	Ja
Strömförbrukning (typiskt):	8.4 W
Drifttemperatur (TT):	0 - 60 °C
Relativ luftfuktighet i drift (VV):	0 - 95 procent
DIN-skena montering:	Ja
Lagra och vidarebefordra:	Ja
Fiberoptisk kontakt:	FX
Kabelteknik för fiber-ethernet:	100BASE-FX
Terminalblockport:	Ja