Tenderfoot Electronics SVF-1 Bruksanvisning
Läs gratis den bruksanvisning för Tenderfoot Electronics SVF-1 (6 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 4 recensioner. Har du en fråga om Tenderfoot Electronics SVF-1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
SVF-1 Manual
SVF-1
State Variable Filter
Manual revision 1/11/2020
1
SVF-1 Manual
Table of Contents
Page 3
● Overview
● Installation
◦Connecting power to the module
Page 4
● Panel Layout
Page 5
● V/Oct Calibration
Page 6
● Important things to note and remember
● Contact Us
2
SVF-1 Manual
Overview
SVF-1 is a state variable filter with voltage controlled cutoff and resonance. The SVF-1
self-oscillates when the resonance is turned up and has a 1V/octave input for use as a
sine wave VCO. The resonance circuit includes a Q control, a drive control, and a
more/less polite to crank up the resonance even more. The Q control is also controllable
via a CV input jack. All outputs are available simultaneously in Low Pass, Band Pass, High
Pass, and Notch mode.
Installation
Tenderfoot Electronics modules are designed to be used with a Eurorack-compatible case
and power supply. Before installing a new module into your case, please ensure that your
power supply and case have sufficient space and available capacity to power the module.
The SVF-1 draws current from the +12V and -12V rails, and can be used in cases without
a 5V rail.
Failure to adequately power your modules may result in damage to your modules or power
supply. If you are unsure, please contact us before proceeding.
Before installing or removing a module from your rack, ensure that you turn off the power
supply for the case. If a module is removed or installed while the rack power supply is
switched on, it could cause serious damage to either the module, or power supply, or both.
Connecting the power cable to the module:
The power header is labelled at one end with a bold stripe,
and the words “red stripe -12V”. Align the red stripe on the
ribbon cable with the “red stripe” label on the PCB.
Once the cable is attached to the module, connect the
16-pin end of the cable to your case's power supply, again
ensuring the red stripe lines up with that of the power
supply PCB.
Using the included screws, screw the module on to your
rails, power up, and enjoy! If at any time you notice
irregularities in the operation of the module, turn off the
case and inspect all connections and cables.
3
Produktspecifikationer
| Varumärke: | Tenderfoot Electronics |
| Kategori: | Inte kategoriserad |
| Modell: | SVF-1 |
Behöver du hjälp?
Om du behöver hjälp med Tenderfoot Electronics SVF-1 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Tenderfoot Electronics Manualer
12 September 2024
12 September 2024
12 September 2024
Inte kategoriserad Manualer
- Ergotools Pattfield
- ALC
- Helight
- AudioControl
- Jinbei
- Alga
- GRAUGEAR
- Pelgrim
- Highpoint
- President
- MADE
- Blue Sky
- Lehle
- Sauter
- Texas Instruments
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025