Tiptop Audio Fold Processor Bruksanvisning
Tiptop Audio
Inte kategoriserad
Fold Processor
Läs gratis den bruksanvisning för Tiptop Audio Fold Processor (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 2.5 recensioner. Har du en fråga om Tiptop Audio Fold Processor eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
www.tiptopaudio.com
Fold Processor
The Fold processor is a 100% analog module built from two sections: rst is a diode ‘folding’ circuit
inspired by the middle section of the Serge wave multiplier module and its output is available at
the OUT jack. The second section feeds from the OUT into a square & divide circuit which is origi-
nal to this module, is output at the SUBDIV OUT. The module is very easy to use, the resulting
sounds are heavily dependent on the type of the incoming signal.
To get started patch as the drawing above, set your Z2040 resonance to max, set the frequency
knob half way, this will cause the Z2040 to self oscillate a natural sine wave (if you don’t have a
Z2040 use the sine output from your Z3000). Plug the Z2040 out into the IN1 on the Fold Proces-
sor (we’ll call it just Fold from now on). Connect the Fold OUT jack to your speaker system and
sweep the FOLD knob, if you don’t hear a sound change the INJECT knob as it might be in the
‘dead’ zone.
You should now hear how the FOLD knob folds the signal and how the Inject input further osets
the signal adding more variations. Both of these knobs can be voltage controlled by CV with the
amount of modulation set by the ATTEN knobs.
Audio System
After getting familiar with the folding eect lets move to the subdivide section and explore it.
Disconnect from the OUT jack and plug it into the SUBDIV out. The subdivider has four divisions
spaces exactly one octave apart, each with a gain knob and mixed into the SUBDIV out jack. First
turn all divisions o, now turn on division 1, use the FOLD and INJECT knobs to hear the eect.
The INJECT might set a ‘dead’ zone at the edges, this is normal and is part of the circuit behavior.
Now increase the input signal frequency and start adding the other divisions, adding lower tones.
The subdivide circuit gets totally wild when sweeping the Fold and Inject knobs, octaves move in
and out and pulses get pulse width modulated. The sound ranges from sweet at times to total
destruction at others; experiment by adding some delay from the Z-DSP and things get really
interesting.
The fold processor works with pure waveforms in its classic use, meaning waveforms from a VCO
or a self oscillating lters, but when complex sounds like samples from ONE or drums are input,
the Fold processor can be used as an analog distortion inside the modular. This is distortion eect
for modular signals similar to how guitar pedals are used for string signals.
Now that you are familiar with the Fold processor start use it in creative ways, put it before or after
a lter, run it in the feedback path of the Z-DSP, or patch the OUT jack into the FM in of a VCO, this
is modular so be creative!
Audio System
LFO
Produktspecifikationer
| Varumärke: | Tiptop Audio |
| Kategori: | Inte kategoriserad |
| Modell: | Fold Processor |
Behöver du hjälp?
Om du behöver hjälp med Tiptop Audio Fold Processor ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Tiptop Audio Manualer
19 Mars 2025
30 Januari 2025
2 Oktober 2024
22 September 2024
11 September 2024
23 Augusti 2024
19 Augusti 2024
18 Augusti 2024
16 Augusti 2024
11 Augusti 2024
Inte kategoriserad Manualer
- Grundig
- Fujitsu
- Omnitronic
- Honda
- Asus
- I.safe Mobile
- Coolaroo
- BERTSCHAT
- EQ Acoustics
- Optex
- Lazer
- RTS
- Lampa
- AudioQuest
- Sevenoak
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025