Tripp Lite SREXTENDER Bruksanvisning

Tripp Lite Inte kategoriserad SREXTENDER

Läs gratis den bruksanvisning för Tripp Lite SREXTENDER (20 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 3.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om Tripp Lite SREXTENDER eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/20

Owner’s Manual

SREXTENDER

Rack Enclosure Extension Frame

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this

manual. Failure to comply may invalidate the warranty.

• Theinstructionsinthismanualareforcommonrackenclosuretypesandmaynotbeappropriateforallmountingapplications.Youmust

determine the ﬁtness of hardware and procedures before mounting. If hardware or procedures are not suitable for your application, contact the

manufacturer of your equipment for a solution.

• Rackmountequipmentmaybeextremelyheavy—becarefulwhenmovingorliftingequipment.Useoneormoreassistantsifnecessary.

Preparation

Note: Tripp Lite recommends using an assistant during installation. Descriptions of left and right are relative to the rear of your rack

enclosure. Illustrations may differ slightly from your enclosure, but procedures are similar for 48U, 42U and 25U enclosures unless

otherwise noted.

• Phillips-headScrewdriver(user-supplied;cordlessscrewdriverrecommended)

Tools Required

1111W.35thStreet,Chicago,IL60609USA

(773)869-1234•www.tripplite.com

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Español 8

Français 15

A B C D E H N

48/42U

1-1

Preparation (continued)

Note: The hinge swivels H and 12 hinge swivel screws L are pre-installed in the vertical sections A through D.

Parts List (If any parts are missing, contact Tripp Lite.)

ALowerLeftVerticalSection(1)

BLowerRightVerticalSection(1)

CUpperLeftVerticalSection(1)

DUpperRightVerticalSection(1)

ETopSection(1)

FBottomSection(1)

G1UBlankingPanels(3)

HHingeSwivels(6-allpre-installed)

IHinges(4)

JCableManagerBrackets(2)

KM6x12mmFlat-HeadScrews(8)

LM6x12mmPan-HeadScrews

andWashers(14total-12pre-installed)

MM5x10mmPan-HeadScrews

andWashers(40)

NGroundingCable(1)

OM5x20mmPan-HeadScrewsand

Washers(4)

PM4x8mmPan-HeadScrews

andWashers(8)

1 – Frame Assembly

Note: For 25U enclosures, you will use only the lower vertical sections A and B. You will not use the upper vertical sections C and D.

For 48U and 42U enclosures, you will use all four vertical sections.

(For25Uenclosures,skipthisstep.)Slidethelowerleftvertical

section A inside the upper left vertical section C as shown.

Repeatforthelowerrightverticalsection B and the upper right

vertical section D. The vertical sections are not interchangeable,

so refer to the diagram to conﬁrm that you’re assembling the

correct sections.

1-1

48U

42U

A AB B

C CD D

1-2

1-3

1-4

1-5

1 – Frame Assembly (continued)

(For25Uenclosures,skipthisstep.)Alignthesetoffourscrew

holes in the lower left vertical section A and the upper left

vertical section C.Usethelowersetofscrewholesfor48U

enclosures(thiswillmaketheverticalsectionlonger).Usethe

uppersetofscrewholesfor42Uenclosures(thiswillmakethe

verticalsectionshorter).InsertfourM5x10mmscrewsand

washers Mandtightensecurely.(Startallthescrewsbefore

tightening.)Repeatforthelowerrightverticalsection B and the

upper right vertical section D.

Insert the lower end of the left vertical section into the

bottom section Fasshown.Alignthescrewholes,insertfour

M5x10mmscrewsandwashers Mandtightensecurely.(Start

allthescrewsbeforetightening.)Repeatthisstepfortheright

vertical section.

Insert the upper end of the left and right vertical sections into the

top section E.Alignthescrewholes,inserteightM5x10mm

screws and washers Mandtightensecurely.(Startallthescrews

beforetightening.)

Insertthe1Ublankingpanels G into the top section E.

EachblankingpanelwillsnapintoplacewiththeTrippLitelogo

facingoutward.Theblankingpanelsmayberemovedtoinstall

standard19-inchrackaccessoriesupto3U–contactTrippLite

for more information.

1-2

1-3

1-4

1-5

Produktspecifikationer

Varumärke:	Tripp Lite
Kategori:	Inte kategoriserad
Modell:	SREXTENDER
Enhetsplacering:	Semi-ingebouwd
Typ av operation:	Touch
Inbyggd display:	Ja
Vikt:	52000 g
Bredd:	600 mm
Djup:	570 mm
Höjd:	850 mm
Antal platsinställningar:	12 couverts
Dörrfärg:	Niet van toepassing
Indikering av återstående tid:	Ja
Barnlås:	Ja
Torkningsklass:	A
Cykelns längd:	171 min
Ljudnivå:	44 dB
Årlig-energiförbrukning:	257 kWu
Förpackningens vikt:	55000 g
Förpackningens bredd:	644 mm
Djuppackning:	661 mm
Förpackningshöjd:	889 mm
Energieffektivitetsklass (gammal):	A++
Vattenförbrukning per cykel:	10 l
Integrerad timer:	Ja
Antal tvättprogram:	5
Färgkontrollpanel:	Black, White
Typ av bästa fack:	Mand
Saltindikator:	Ja
Sköljmedelsindikator:	Ja
Översvämningsskydd:	Ja
Halvlastad:	Ja
Energiförbrukning per cykel:	0.9 kWu
Årlig vattenförbrukning:	2800 l
Korgar justerbar placering:	Lower, Upper