Triton FetHead Broadcast Bruksanvisning
Triton
Inte kategoriserad
FetHead Broadcast
Läs gratis den bruksanvisning för Triton FetHead Broadcast (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 41 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 21 recensioner. Har du en fråga om Triton FetHead Broadcast eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
FetHead Broadcast
Philosophy
FetHead Broadcast is an in-line microphone preamplifier specially designed for operating in challenging
live environments. offers 23dB of low noise high quality amplification which can be FetHead Broadcast
applied to either dynamic or condenser microphones as phantom power is transferred to the microphone.
Recommended application
In broadcast or live performance situations, a microphone signal often travels through long cables before
reaching the mixing desk. When small microphone signals travel adjacent to power lines or dimmed light
cables, audible signal interference is likely to be induced into the microphone cable. Fethead Broadcast
amplifies the microphone signal before the cable and greatly improves the signal to noise ratio offering a
much higher quality signal to the mixing desk. A low impedance output buffer enables output drive to
long cables (up to 3000 meters). Another advantage is that the FetHead Broadcast does not need main
supplies or batteries.
Operation
Connect your microphone on the input XLR of your . At the opposite side an XLR cable Fethead Broadcast
runs from your Fethead Broadcast to the mixer/preamp .it’s ready for use with any type of phantom
powered setup. Fethead Broadcast uses phantom power to power its circuitry, but also provides enough
phantom power to power the connected microphone.
Circuit topology
FetHead Broadcast utilizes a low noise FET amplifier circuit, which reveals every detail, followed by a low
impedance output buffer which reveals every detail with pinpoint accuracy and offers high-end sound
quality.
Features
• Low noise Class A FET amplifier
• Low impedance output buffer
• 23 dB amplification
• Rugged enclosure with balanced XLR input/output
• internal rumble filter
• frequency response 40Hz-100 kHz (+/- 1dB)
• Z-in 680 Ω
• Circuit is powered with 48V phantom power
Dimensions
height: 1,22” / 31mm
width: 1” / 26mm
length: 3,11” / 79mm
weight: 80 g
Registration
Thank you for purchasing a Triton Audio Fethead Broadcast.
To register your product please go to: tritonaudio.com/support/product-registration/
Produktspecifikationer
| Varumärke: | Triton |
| Kategori: | Inte kategoriserad |
| Modell: | FetHead Broadcast |
Behöver du hjälp?
Om du behöver hjälp med Triton FetHead Broadcast ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Triton Manualer
22 Februari 2025
7 December 2024
7 December 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
Inte kategoriserad Manualer
- Scancool
- Magmatic
- Orava
- NAD
- Taga Harmony
- AXI
- Kisag
- Woox
- Listen
- IDENTsmart
- Little Tikes
- Kemo
- IQAir
- Deity
- Akuvox
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025