TRIUS Trap Master Bruksanvisning

TRIUS Inte kategoriserad Trap Master

Läs gratis den bruksanvisning för TRIUS Trap Master (12 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 5 recensioner. Har du en fråga om TRIUS Trap Master eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/12

Instruction Manual

Trius®a subsidiary of Lyman Products Corp 475 Smith Street, Middletown, CT 06457

800-22-LYMAN or 860-632-2020 www.triustraps.com

Trius 1 Step Page 2

Trius Birdshooter Page 5

92S Trius Trap Page 7

Trius Trap Master Page 9

Congratulations

You have just purchased a unique design and easy to use target trap.

Please read all directions before assembling and using your new trap.

Trius®Traps – 1 Step www.triustraps.com2

ASSEMBLY INSTRUCTIONS:

Tools Needed: 2 adjustable wrenches or 9/16

socket/open end or box end wrenches.

Your Trius 1 Step is preassembled as much as possible

before shipping. The trap has been tested with the main

spring that has been sent with it. By following the

instructions, the trap should go together quickly and

easily. Do not tighten nuts and bolts before all are in

place. When tightening the lock nuts, remember lock nuts

seem tight before really snug.

Put rear support with pedal, trap base and stabilizer together as shown in Illus. A. Please note that trap

base goes in between the rear support and stabilizer.

Put bolt #1 from bottom through rear support and trap base

as shown. Tighten nut finger tight.

Put bolt #2 from bottom through rear support, add 2 wash-

ers, then through the stabilizer. Tighten nut finger tight.

Put bolt #3 from bottom through trap base, add 1 washer,

then through stabilizer. Tighten nut finger tight.

Put bolt #4 from bottom through rear support, trap base and

stabilizer. Tighten nut finger tight.

You are now ready to tighten all bolts and nuts.

Now place arm assembly onto trap base and secure with

lock nut and elevation knob.

ATTACHING MAIN SPRING:

(Illus. B.) Raise pedal, extend arm forward, attach main spring to spring hook, then onto eyebolt assembly.

Put eyebolt through rear bracket, add washer and adjusting knob. Important: Put spring through spring hook

as shown. Do not push on pedal until chain is adjusted properly!

TENSION ADJUSTMENT:

Tighten tension knob just enough to have

eyebolt take up full thread of knob. This

should throw a fine target and be just right

for teaching new shooters. For faster more

difficult targets, increase tension by tighten-

ing knob. Doubles usually require higher

tension. A regulation trap target flight is

between 8 and 12 feet high at a point 10

yards from the trap, and the horizontal dis-

tance is between 48 and 52 yards.

TRIUS 1-STEP

Trius®Traps – 1 Step www.triustraps.com3

IMPORTANT

ADJUSTING HEIGHT AND RELEASE CHAIN:

Pedal should be at bottom of stroke when trigger releases arm.

TO ADJUST - Remove chain at pedal.

Secure frame at desired angle. (middle holes most popular). (Illus. C)

FLAT: bottom hole, difficult shot, short air time for targets

MEDIUM: middle holes, most popular, best for beginners

HIGH: top hole, most difficult shot

Arm should be extended in the release position.

With pedal at bottom of stroke – resting between rear stabilizer, pull chain snug until release trigger is at

rear of slot (Illus. D) with minimum tension on chain/spring. Place chain onto pedal bolt.

Tighten wing nut so threads of bolt are flush with wing nut hole. (Illus. E)

Chain should be loose on pedal bolt. When adjusted properly, pedal should release trigger at bottom of

stroke.

IF NOT RELEASING TARGETS, SHORTEN CHAIN ON PEDAL BOLT.

IF RELEASING TARGETS TOO SOON, LENGTHEN CHAIN ON PEDAL BOLT. Safe operation of your trap

is as important as safe gun handling. DO NOT STEP ON PEDAL UNTIL PATH OF ARM AND TARGET(S)

ARE CLEAR.

CDE

OPERATION OF TRAP: Become familiar with trap before throwing targets and shooting. The trap’s front legs

should be pushed into the ground to help secure the trap for more consistent throws.

DIRECTIONAL ADJUSTMENT:

To change the direction that a traget will fly, change its position on the arm. For a left target, move the tar-

get fully up the arm against the high angle clip. If a center target is desired, move it down the arm slightly.

For a right target, move it further down the arm.

Produktspecifikationer

Varumärke:	TRIUS
Kategori:	Inte kategoriserad
Modell:	Trap Master
Bredd:	305 mm
Djup:	330 mm
Ethernet LAN:	Ja
Antal USB 2.0-portar:	2
VGA (D-Sub) port(ar):	1
Antal Ethernet LAN (RJ-45)-portar:	2
Förvaringstemperatur:	-40 - 70 °C
Processoruttag:	Socket B (LGA 1366)
Processorfabrikant:	Intel
Maximalt internminne:	96 GB
Förvaringsfuktighet:	5 - 95 procent
PCI Express sleufhoeveelheid:	4
ETC:	Ja
Ethernet-gränssnittstyp:	Gigabit Ethernet
Chipset moderkort:	Intel® 5520
RAID-stöd:	Ja
Gränssnitt för lagringsenheter som stöds:	Serial Attached SCSI (SAS)
PS/2-port(ar):	2
Seriell port(ar):	2
PCI Express x4-platser:	1
Komponent för:	Server
Minnesspänning:	1.35, 1.5 V
Typer av RAID:	0, 1,5, 10
Icke-ECC:	Ja
Antal processorer som stöds:	2
Intel® Xeon-serien:	5500,5600
Antal DIMM-platser:	12
Minnestyper som stöds:	DDR3-SDRAM
Moderkort södra bro:	Intel ICH10R
Wifi:	Nee
Drifttemperatur (TT):	10 - 35 °C
Relativ luftfuktighet i drift (VV):	8 - 90 procent
PCI Express x8 (Gen 2.x)-platser:	3
Moderkorts formfaktor:	Verlengd ATX
Minnesklockhastigheter som stöds:	800,1066,1333 MHz
BIOS-typ:	AMI
BIOS-minnesstorlek:	32 Mbit
ACPI-version:	3.0
Antal SATA-anslutningar:	6
USB 2.0-anslutningar:	4
PCI Express x16 (Gen 2.x)-platser:	1
IPMI LAN (RJ-45) port:	Ja
Processor antal kärnor stöds:	6
QPI stöds:	6.4 GT/s