Ubiquiti Networks UniFi UAP-AC-HD Bruksanvisning
Ubiquiti Networks
Router
UniFi UAP-AC-HD
Läs gratis den bruksanvisning för Ubiquiti Networks UniFi UAP-AC-HD (32 sidor) i kategorin Router. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.0 stjärnor baserat på 6.5 recensioner. Har du en fråga om Ubiquiti Networks UniFi UAP-AC-HD eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/32
802.11ac Wave 2
Enterprise Wi-Fi Access Point
Model: UAP-AC-HD
Introduction
Thank you for purchasing the Ubiquiti Networks®
UniFi®802.11ac Wave 2 Enterprise Wi-Fi Access Point.
This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
IMPORTANT: The UAP-AC-HD requires the UniFi
Controller v5.4 or higher, available at:
www.ubnt.com/download/unifi
Package Contents
UniFi AP AC HD Mounting
Plate
Ceiling Backing
Plate
Ceiling Screws
(Qty. 4)
Keps Nuts
(Qty. 4)
T-Bar Mounts
(Qty. 2)
T-Bar Screws
(Qty. 2)
Allen Wrench
802.11ac Wave 2
Ente rpr ise W i-Fi Acc es s Point
Model: UA P- AC -H D
Wall Screw
(Qty. 4)
Screw Anchors
(Qty. 4)
Release Tool Cable Feed
Plug
Quick Start
Guide
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable ™ is
designed for outdoor installations. It is the professional installer’s responsibility to follow local
country regulations, including operation within legal frequency channels, output power, and
Dynamic Frequency Selection (DFS) requirements.
Installation Requirements
• Phillips screwdriver
• Drill and drill bit (8 mm for wall mounting or 3 mm for ceiling
tile mounting)
• Optional: Drywall or keyhole saw (to cut 18 mm hole for
Ethernet cable feed)
• Cat5/6 UTP cable for indoor installations
Outdoor Installation Requirements
IMPORTANT: The UAP-AC-HD may be installed outdoors
under an eave or other protected location. Do not
install the UniFi AP in an open environment.
• Mounting location should be at least 60 cm (2 ft) from the
edge of the eave or ceiling.
• Cable feed opening must be directed away from the open
environment.
• Cable feed must be pointed downwards when wall-mounted.
• Shielded Category 5 (or above) cabling should be used
for all outdoor wired Ethernet connections and should be
grounded through the AC ground of the PoE.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
System Requirements
• Linux, MacOSX, or Microsoft Windows 7/8/10
• Java Runtime Environment 1.6 (1.8 or newer recommended)
• Web Browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Controller software v5.4 or newer (available at:
www.ubnt.com/download/unifi)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address
as well as for the wireless clients after deployment)
• A UniFi Cloud Key or management station running the UniFi
Controller v5.4 (or newer) software, located either on-site
and connected to the same Layer 2 network, or off-site in the
cloud or NOC
US-16-150W
USG-PRO-4
(DHCP Server)
Internet
UAP-AC-HD
UAP-AC-M-PRO
UAP-AC-PRO
LAN
WAN
UniFi Hybrid
Cloud Install
Remote Access to
UniFi Controller
DOWNLOAD THROUGHPUT & LATENCY DEVICES ON 2.4 GHZ CHANNEL
DEVICES ON 5 GHZ CHANNEL
UPLOAD THROUGHPUT & LATENCY
LATENCY THROUGH PUT
SPEED TEST
msec Mbps
7 0.94 1
2.33
25 2 2
597
0.9 116
200+0 700+0
0.01 413
2290.22 118
547
ACTIVE DEVI CE
WAN
Inacve 0Pend i ng
0Inacve 0Pend i ng
0
7
ACTIVE DEVI CES
Inacve 0Pend i ng
0
118
ACTIVE DEVI CES
LAN WLAN
DEEP PACKET INSPECTIONCLIENTSDEVICES
250200
150
10050
0
108
6
42
0
24 HRS 12 HRS NOW
Avg/Max Throughput Latency
Latency [msec]
Throughp ut [Mbps]
100
8060
40
20
0
10
86
4
2
0
24 HRS 12 HRS NOW
Latency [msec]
Throughp ut [Mbps]
Netw ork Pr ot oc olsStream ing M e di a
Web / Web 2.0File Tr ans f er
Social N etw orkOther
Motoro laLenovo
Samsung ED ell
AcerO ther
WLANLAN
WAN
1187
1
582 GB23.3 GB
22.7 GB8.47 GB
3.6 GB5.46 GB
258241
220213
130110
126
DEVICES
645 GB
TRAFF IC
1172
CLIENT S
1 2 3 4 5 6 7 8 9 10 11
36 4 0 44 4 8 52 5 6 60 6 4
100 104 1 08 1 1 2 11 6 12 0 12 4 1 2 8
132 136 140 144 149 153 157 161 165
CURRE N T SITE
Def a ult US ERNA ME
admi n
DOWNLOAD THROUGHPUT & LATENC Y DEVICES ON 2.4 GHZ CHANNEL
DEVICES ON 5 GHZ CHANNEL
UPLOAD THROUGHPUT & LATE NC Y
LATENCY THROUGHPUT
SPEED TE S T
msec Mbps
7 0.9 4 1
2.33
25 22
597
0.9 116
200+0 700+0
0.01 413
2290 .2 2 118547
ACTIVE DEVICE
WAN
Inacve 0
Pending
0
Inacve 0
Pending
0
7
ACTIVE DEVICES Inacve 0
Pending
0
118
ACTIVE DEVICES
LAN WLAN
DEEP PACKE T INSPE CT IONCLIENTSDEVICES
250
200150
10050
0
10
86
42
0
24 HRS 12 HRS NOW
Avg/Max Throu g h p u t Latency
Latency [msec]
Throug h p u t [Mbps]
100
80
6040
200
10
8
64
20
24 HRS 12 HRS NOW
Latency [msec]
Throug h p u t [Mbps]
Network Protocols
Streaming MediaWeb / Web 2.0File Transfer
Social NetworkOther
Motorola
LenovoSamsungEDell
AcerOther
WLANLAN
WAN
1187
1
582 GB
23.3 GB22 .7 GB8.47 GB
3.6 GB5.46 GB
258
241220213
130110
126
DEVICE S 645 GB
TRAF F IC
1172
CLIEN T S
1 2 3 4 5 6 7 8 9 10 11
36 40 44 48 52 56 60 64
100 104 108 112 116 120 124 128
132 136 140 144 149 153 157 161 165
CURR E NT SIT E
Default
USER NAME
admin
Sample Network Diagram
All UniFi devices support off-site management controllers.
For setup details, see the User Guide on the website:
www.ubnt.com/download/unifi
Mounting Plate
The Mounting Plate offers a variety of mounting holes for
different applications. The legend printed on the Mounting
Plate identifies the holes used for each application.
Upgrade from UAP-AC-PRO
The UAP-AC-HD uses the same mounting hardware as the
UAP-AC-PRO, so you only need to remove the UAP-AC-PRO
and replace it with the UAP-AC-HD. To begin the upgrade:
1. into the UAP-AC-PRO Insert the Release Tool Security
Slot to disengage the lock. Then turn the UAP-AC-PRO
counterclockwise and lift it off of the mounting bracket.
Security Slot
UAP-AC-PRO (wall mount installation)
2. Unplug the Ethernet cable from the port.Main
3. section.Go to the Connecting Ethernet
6. Rotate the UniFi AP clockwise until the tabs lock into place
and the Lock Tab engages.
Ceiling Tile Mount
1. Remove the ceiling tile.
2. Place the Ceiling Backing Plate in the center of the ceiling
tile. Mark the four mounting screw holes and an 18 mm
hole for the Ethernet cable feed.
Optional 18 mm Hole for Ethernet Cable
Feed through the Ceiling Tile
3. Use a 3 mm drill bit to drill the screw holes, and cut or drill
the 18 mm hole for the Ethernet cable feed.
4. , ceiling Insert the through the Ceiling Screws Mounting Plate
tile, and . Fasten the screws using the Ceiling Backing Plate
Keps Nuts. Then feed the Ethernet cable through the tile
and bracket.
7. into the holes marked “B” Insert the included T-Bar Screws
on the and then secure the plate to the Mounting Plate,
T-Bar Mounts.
8. Drop the Ethernet cable between the plate and T-bar.
9. Perform the steps in the section, and Connecting Ethernet
then return to step 10.
10. Align the on the top edge of the UniFi AP with the Arrow
Arrow Mounting Plate on the .
Arrow
Arrow
Lock Tab
11. Rotate the UniFi AP clockwise until the tabs lock into place
and the Lock Tab engages.
12. Set the ceiling tiles back into place.
Junction or Outlet Box Mount
1. Use the legend printed on the to select the Mounting Plate
appropriate mounting holes for your installation.
2. Pull the Ethernet cable through the , and Mounting Plate
attach the Mounting Plate to the junction or outlet box
using at least two screws (not included).
Note: For in-wall applications, position the Mounting
Plate Arrow with the pointing upwards.
3. Perform the steps in the section, and Connecting Ethernet
then return to step 4.
4. Align the on the top edge of the UniFi AP with the Arrow
Arrow Mounting Plate on the .
Lock Tab
Arrow
Arrow
5. Rotate the UniFi AP clockwise until the tabs lock into place
and the Lock Tab engages.
Connecting Ethernet
1. Remove the rubber port cover from the UniFi AP.
2. If the Ethernet cable runs along the mounting surface, skip
to step 3. If the Ethernet cable is fed through the wall or
ceiling, insert the Cable Feed Plug .
3. Feed the Ethernet cable through the port cover.
Note: The feed hole will stretch to accommodate the
RJ45 connector, and then seal around the cable.
4. Connect the Ethernet cable to the Main port and replace
the port cover. Return to the appropriate instructions.
Software Installation
Download and install the latest version of the UniFi Controller
software. Launch it and follow the on-screen instructions. The
software and step-by-step instructions in the User Guide are
available at: www.ubnt.com/download/unifi
After you have installed the software and run the UniFi
Installation Wizard, a login screen will appear for the UniFi
Controller management interface. Enter the Admin Name and
Password that you created and click . Log In
You can manage your wireless network and view network
statistics using the UniFi Controller management interface.
For information on configuring and using the UniFi Controller
software, refer to the User Guide.
Mobile App Installation
Ubiquiti Networks also offers the UniFi mobile app, which
is available from the App Store (iOS) or Google Play™ Store
(Android). You can use it to provision a UniFi AP for basic
functionality without configuring a UniFi Controller. It also
allows seamless provisioning of APs for remote controllers
(controllers not on the same Layer 2 network) and easy access
to local controllers and those monitored on unifi.ubnt.com
Specifications
UAP-AC-HD
Dimensions 220 x 220 x 48.1 mm
(8.66 x 8.66 x 1.89")
Weight
with Mounting Kit
700 g (1.54 lb)
830 g (1.83 lb)
Networking Interface (2) 10/100/1000 Ethernet Ports
Buttons Reset
Power Method PoE+ 802.3at
Power Supply UniFi Switch (PoE)
Max. Power Consumption 17W
Operating Frequency 2.4 GHz
5 GHz
Max. TX Power
2.4 GHz
5 GHz
25 dBm
25 dBm
Antennas
2.4 GHz
5 GHz
(2) Dual-Port, Dual-Polarity
(2) Dual-Port, Dual-Polarity
Antenna Gain
2.4 GHz
5 GHz
3 dBi
4 dBi
Wi-Fi Standards 802.11 a/b/g/n/ac/ac-wave2
Wireless Security WEP, WPA-PSK,
WPA-Enterprise (WPA/WPA2, TKIP/AES)
Mounting Wall/Ceiling/Junction Box (Kits Included)
Operating Temperature -10 to 70° C (14 to 158° F)
Operating Humidity 5 to 95% Noncondensing
Certications CE, FCC, IC
Produktspecifikationer
| Varumärke: | Ubiquiti Networks |
| Kategori: | Router |
| Modell: | UniFi UAP-AC-HD |
Behöver du hjälp?
Om du behöver hjälp med Ubiquiti Networks UniFi UAP-AC-HD ställ en fråga nedan och andra användare kommer att svara dig
Router Ubiquiti Networks Manualer
3 Oktober 2024
26 September 2024
13 September 2024
13 September 2024
9 September 2024
30 Augusti 2024
25 Augusti 2024
25 Augusti 2024
22 Augusti 2024
20 Augusti 2024
Router Manualer
- Lumantek
- Tenda
- Vivanco
- Porter-Cable
- Silverline
- Juniper
- Konig
- Draytek
- KPN
- Trust
- LTS
- Cotech
- Kramer
- BT
- Patton
Nyaste Router Manualer
13 Juni 2025
13 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
9 April 2025